Date: Fri, 27 Dec 2002 06:33:57 -0800 From: Pat Lathem <plathem@ivestnw.net> To: Kirill Bezzubets <kirill@solaris.ru> Cc: freebsd-mobile@freebsd.org Subject: Re: 4.7 -> 5.0 Pccard problems (more info) Message-ID: <3E0C64D5.60209@ivestnw.net> In-Reply-To: <20021227092429.GA5786@solaris.ru> References: <BAY1-F1633JCYaHXPDl0001ce01@hotmail.com> <20021226094524.GA10382@solaris.ru> <3E0B1056.6050300@ivestnw.net> <20021227092429.GA5786@solaris.ru>
next in thread | previous in thread | raw e-mail | index | archive | help
I am running 5.0 current from a few days ago. I upgrade fairly often hoping that it will be fixed. When I booted with the -v flag, everything proceeded normally until I attempted to power up the slot the card was in (pccardc power 0 1) . The first two lines are shown to the console, and then the third line is printed repeatedly: pcic0: reset 1 int is 0 stat is 0 pcic0: reset 2 int is 0 stat is 0 pcic0: reset 3 int is 0 stat is 0 (<-- this one is then repeated in a loop until the slot is powered down) Does anyone know what this means? After I power it down (pccardc power 0 0): pcic0: reset 0 Here is the output from dmesg (I am still using OLDCARD) [trashcan]~: dmesg | grep pcic0 pcic0: <TI PCI-1410 PCI-CardBus Bridge> irq 11 at device 6.0 on pci2 pcic0: PCI Memory allocated: 0xd0200000 pcic0: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][CSC serial isa irq] pccard0: <PC Card 16-bit bus (classic)> on pcic0 [trashcan]~: dmesg | grep pci2 pci2: <ACPI PCI bus> on pcib2 pci2: <simple comms> at device 4.0 (no driver attached) pci2: <serial bus, FireWire> at device 5.0 (no driver attached) pcic0: <TI PCI-1410 PCI-CardBus Bridge> irq 11 at device 6.0 on pci2 fxp0: <Intel Pro/100 Ethernet> port 0x3040-0x307f mem 0xd0215000-0xd0215fff irq 10 at device 8.0 on pci2 Pat Lathem Kirill Bezzubets wrote: >On Thu, Dec 26, 2002 at 06:21:10AM -0800, Pat Lathem wrote: > > > >>>>cbb0: <TI1410 PCI-CardBus Bridge> irq 11 at device 6.0 on pci2 >>>>cardbus0: <CardBus bus> on cbb0 >>>>pccard0: <16-bit PCCard bus> on cbb0 >>>> >>>> >>>> >>The card is a supported IBM 56k modem (I also have been expirementing >>with a Linksys wireless card). The kernel does not say anything when I >>insert or remove it (with GENERIC), which is why I assumed it was not >>being detected properly. Since I posted the, I have reverted to the >>kernel OLDCARD. After the computer boots, I can run 'pccardc power 0 1' >>and it starts to initialize the card, but fails to read the correct >>vendor string from the pccard. I'm currently changing the hints file (at >>the advice of Greg Smith) to see if it can work. My question is this: Is >>this is a regression? In 4.7-stable I only had to add to /etc/rc.conf >>"pccard_enable="YES"' and reboot (or start pccardd) to get my cards >>working. Was I just lucky that it just worked the first time, or is >>there a problem? >> >> > >One more thing from your dmesg output (sorry, just noticed..): > >cbb0: Unsupported card type detected > >I guess it's a kind of bug with TI1410 (???), not sure though. >Because mine is TI1131 PCI-CardBus Bridge and everything works well >with both 16bit(PCCard) and 32bit(CardBus) cards using NEWCARD. >Also it did work in 4-STABLE since 4.3 with PCCards. > >My FreeBSD is 5.0-RC1. > >Are you using 5-CURRENT or 5.0-RC1? Btw, dmesg from "boot -v" could help >much more to determine what the problem is. > > > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3E0C64D5.60209>