Date: Wed, 25 Apr 2007 20:55:39 -0400 From: Chris Slothouber <chris@hier7.com> To: KAYVEN RIESE <kayve@sfsu.edu> Cc: FreeBSD-questions@FreeBSD.org Subject: Re: mesg = dmesg Message-ID: <462FF88B.1030007@hier7.com> In-Reply-To: <Pine.SOC.4.64.0704251640010.21999@libra.sfsu.edu> References: <462F15B4.4010201@webmail.sub.ru> <200704251208.34248.jhb@freebsd.org> <004e01c7876c$2ce8a3d0$0c00a8c0@Artem> <Pine.SOC.4.64.0704251640010.21999@libra.sfsu.edu>
next in thread | previous in thread | raw e-mail | index | archive | help
KAYVEN RIESE wrote: > > i sent a post from a puter with a bad "d" key. that's why > my subject didn't say "dmesg" like it should have. > > sorry. > > > here is a dmesg output: > > Copyright (c) 1992-2006 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 6.1-RELEASE #0: Sun May 7 04:32:43 UTC 2006 > root@opus.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Intel(R) Pentium(R) M processor 1.73GHz (600.02-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0x6d8 Stepping = 8 > > Features=0xafe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE> > > Features2=0x180<EST,TM2> > AMD Features=0x100000<NX> > real memory = 536084480 (511 MB) > avail memory = 515223552 (491 MB) > kbd1 at kbdmux0 > acpi0: <A M I OEMRSDT> on motherboard > ACPI-0356: *** Error: Region EmbeddedControl(3) has no handler > ACPI-1304: *** Error: Method execution failed > [\\_SB_.PCI0.SBRG.EC0_.ACS_] (Node 0xc33998c0), AE_NOT_EXIST > ACPI-1304: *** Error: Method execution failed [\\_SB_.AC__._INI] > (Node 0xc33993e0), AE_NOT_EXIST > ACPI-0356: *** Error: Region EmbeddedControl(3) has no handler > ACPI-1304: *** Error: Method execution failed > [\\_SB_.PCI0.SBRG.EC0_.BATS] (Node 0xc33998a0), AE_NOT_EXIST > ACPI-1304: *** Error: Method execution failed [\\_SB_.BAT0._STA] > (Node 0xc339d720), AE_NOT_EXIST > ACPI-0239: *** Error: Method execution failed [\\_SB_.BAT0._STA] > (Node 0xc339d720), AE_NOT_EXIST > acpi0: Power Button (fixed) > acpi_ec0: <Embedded Controller: GPE 0x1c> port 0x62,0x66 on acpi0 > Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 > cpu0: <ACPI CPU> on acpi0 > acpi_throttle0: <ACPI CPU Throttling> on cpu0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > agp0: <Intel 82855 host to AGP bridge> mem 0xe0000000-0xefffffff at > device 0.0 on pci0 > pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > pci1: <display, VGA> at device 0.0 (no driver attached) > uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xe800-0xe81f > irq 11 at device 29.0 on pci0 > uhci0: [GIANT-LOCKED] > usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0 > usb0: USB revision 1.0 > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xe880-0xe89f > irq 5 at device 29.1 on pci0 > uhci1: [GIANT-LOCKED] > usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1 > usb1: USB revision 1.0 > uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 2 ports with 2 removable, self powered > uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xec00-0xec1f > irq 10 at device 29.2 on pci0 > uhci2: [GIANT-LOCKED] > usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2 > usb2: USB revision 1.0 > uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub2: 2 ports with 2 removable, self powered > ehci0: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> mem > 0xffaffc00-0xffafffff irq 10 at device 29.7 on pci0 > ehci0: [GIANT-LOCKED] > usb3: EHCI version 1.0 > usb3: companion controllers, 2 ports each: usb0 usb1 usb2 > usb3: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> on ehci0 > usb3: USB revision 2.0 > uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 > uhub3: 6 ports with 6 removable, self powered > pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 > pci2: <ACPI PCI bus> on pcib2 > bge0: <Broadcom BCM5788 Gigabit Ethernet, ASIC rev. 0x3003> mem > 0xff9f0000-0xff9fffff irq 4 at device 0.0 on pci2 > miibus0: <MII bus> on bge0 > brgphy0: <BCM5705 10/100/1000baseTX PHY> on miibus0 > brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, > 1000baseTX-FDX, auto > bge0: Ethernet address: 00:11:d8:22:c9:91 > cbb0: <RF5C476 PCI-CardBus Bridge> at device 1.0 on pci2 > cardbus0: <CardBus bus> on cbb0 > pccard0: <16-bit PCCard bus> on cbb0 > cbb1: <RF5C476 PCI-CardBus Bridge> at device 1.1 on pci2 > cardbus1: <CardBus bus> on cbb1 > pccard1: <16-bit PCCard bus> on cbb1 > fwohci0: <Ricoh R5C552> mem 0xff9ef800-0xff9effff irq 10 at device 1.2 > on pci2 > fwohci0: OHCI version 1.0 (ROM=1) > fwohci0: No. of Isochronous channels is 4. > fwohci0: EUI64 00:e0:18:00:03:26:4c:e9 > fwohci0: Phy 1394a available S400, 2 ports. > fwohci0: Link S400, max_rec 2048 bytes. > firewire0: <IEEE1394(FireWire) bus> on fwohci0 > fwe0: <Ethernet over FireWire> on firewire0 > if_fwe0: Fake Ethernet address: 02:e0:18:26:4c:e9 > fwe0: Ethernet address: 02:e0:18:26:4c:e9 > fwe0: if_start running deferred for Giant > sbp0: <SBP-2/SCSI over FireWire> on firewire0 > fwohci0: Initiate bus reset > fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode > firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) > firewire0: bus manager 0 (me) > pci2: <network> at device 2.0 (no driver attached) > isab0: <PCI-ISA bridge> at device 31.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel ICH4 UDMA100 controller> port > 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0 > ata0: <ATA channel 0> on atapci0 > ata1: <ATA channel 1> on atapci0 > pci0: <multimedia, audio> at device 31.5 (no driver attached) > pci0: <simple comms, generic modem> at device 31.6 (no driver attached) > acpi_lid0: <Control Method Lid Switch> on acpi0 > acpi_button0: <Sleep Button> on acpi0 > acpi_acad0: <AC Adapter> on acpi0 > battery0: <ACPI Control Method Battery> on acpi0 > battery1: <ACPI Control Method Battery> on acpi0 > acpi_button1: <Power Button> on acpi0 > acpi_tz0: <Thermal Zone> on acpi0 > atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: [GIANT-LOCKED] > psm0: model Generic PS/2 mouse, device ID 0 > sio0: configured irq 3 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0 port 0x2f8-0x2ff irq 3 drq 1 flags 0x10 on acpi0 > sio0: type 16550A > ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77f irq 7 drq > 3 on acpi0 > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > ppc0: FIFO with 16/16/8 bytes threshold > ppbus0: <Parallel port bus> on ppc0 > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > pmtimer0 on isa0 > orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > ums0: vendor 0x2222 Macally Optigo USB Mouse, rev 1.10/6.30, addr 2, > iclass 3/1 > ums0: 3 buttons and Z dir. > Timecounter "TSC" frequency 600023816 Hz quality 800 > Timecounters tick every 1.000 msec > ad0: 57231MB <HTS548060M9AT00 MGBOA53A> at ata0-master UDMA100 > ACPI-1304: *** Error: Method execution failed [\\_SB_.BAT0._BST] > (Node 0xc339d740), AE_AML_NO_RETURN_VALUE > acd0: DVDR <TSSTcorpCD/DVDW TS-L532A/TC51> at ata1-master UDMA33 > Trying to mount root from ufs:/dev/ad0s1a > ACPI-1304: *** Error: Method execution failed [\\_SB_.BAT0._BST] > (Node 0xc339d740), AE_AML_NO_RETURN_VALUE > ACPI-1304: *** Error: Method execution failed [\\_SB_.BAT0._BST] > (Node 0xc339d740), AE_AML_NO_RETURN_VALUE > ACPI-1304: *** Error: Method execution failed [\\_SB_.BAT0._BST] > (Node 0xc339d740), AE_AML_NO_RETURN_VALUE > ACPI-1304: *** Error: Method execution failed [\\_SB_.BAT0._BST] > (Node 0xc339d740), AE_AML_NO_RETURN_VALUE > ACPI-1304: *** Error: Method execution failed [\\_SB_.BAT0._BST] > (Node 0xc339d740), AE_AML_NO_RETURN_VALUE > ACPI-1304: *** Error: Method execution failed [\\_SB_.BAT0._BST] > (Node 0xc339d740), AE_AML_NO_RETURN_VALUE > ACPI-1304: *** Error: Method execution failed [\\_SB_.BAT0._BST] > (Node 0xc339d740), AE_AML_NO_RETURN_VALUE > ACPI-1304: *** Error: Method execution failed [\\_SB_.BAT0._BST] > (Node 0xc339d740), AE_AML_NO_RETURN_VALUE > ACPI-1304: *** Error: Method execution failed [\\_SB_.BAT0._BST] > (Node 0xc339d740), AE_AML_NO_RETURN_VALUE > ACPI-1304: *** Error: Method execution failed [\\_SB_.BAT0._BST] > (Node 0xc339d740), AE_AML_NO_RETURN_VALUE > ACPI-1304: *** Error: Method execution failed [\\_SB_.BAT0._BST] > (Node 0xc339d740), AE_AML_NO_RETURN_VALUE > ACPI-1304: *** Error: Method execution failed [\\_SB_.BAT0._BST] > (Node 0xc339d740), AE_AML_NO_RETURN_VALUE > bge0: link state changed to UP Hi Kayven, It appears as though your BIOS may not be reporting ACPI information to FreeBSD correctly. I might suggest toggling the 'PNP OS Installed' option in your BIOS setup or, failing that, upgrading your BIOS firmware following your motherboard manufacturer's instructions. I hope this information helps. - Chris Slothouber
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?462FF88B.1030007>