Date: Thu, 27 Dec 2001 17:29:44 -0500 (EST) From: Kenneth Wayne Culver <culverk@wam.umd.edu> To: twig les <twigles@yahoo.com> Cc: freebsd-questions@FreeBSD.ORG Subject: Re: multiple panics in 4.4 stable Message-ID: <Pine.GSO.4.21.0112271729180.16111-100000@rac4.wam.umd.edu> In-Reply-To: <20011227190659.38389.qmail@web10104.mail.yahoo.com>
next in thread | previous in thread | raw e-mail | index | archive | help
This is probably bad memory. I've had similar problems and when I replaced the memory, the problems magically went away. Ken On Thu, 27 Dec 2001, twig les wrote: > Hey all, I'm having a devil of a time here with 4.4 > stable. I ssh into my box and sometimes get this > message: > > Segmentation fault - core dumped > > Then I can't su, instead I get a message saying the > > /kernel: pid 207(sh), uid 1001: exited on signal 11 > (core dumped) > > > > I've also gotten panics trying to rebuild the kernel; > after doing a config it gives me a panic message and > reboots. I will paste my dmesg at the end of this > mail-it has three panics in it. > > I'm no programmer but I think the version of Free4.4 > that comes with the new book "FreeBSD Unleashed" may > not be that stable. The machine is a development one > (to be a Snort box) and the hardware is a Supermicro > mobo, 1G RAM (I forget what kind but it's brand-name, > registed, ecc), 18gb Seagate scsi HD, dual p3 1ghz. > As I'm writing this the box panicked and rebooted > itself again. > > > > bash-2.05# dmesg > rq 12 on atkbdc0 > psm0: model IntelliMouse, device ID 3 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem > 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1 at port 0x2f8-0x2ff irq 3 on isa0 > sio1: type 16550A > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on > isa0 > ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE > mode > ppc0: FIFO with 16/16/8 bytes threshold > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > acd0: CDROM <CD-ROM CDU611-H> at ata0-master using > PIO4 > Mounting root from ufs:/dev/da0s1a > da0 at ahc0 bus 0 target 0 lun 0 > da0: <SEAGATE ST318404LW 0006> Fixed Direct Access > SCSI-3 device > da0: 160.000MB/s transfers (80.000MHz, offset 63, > 16bit), Tagged Queueing Enabled > da0: 17501MB (35843670 512 byte sectors: 255H 63S/T > 2231C) > panic: pmap_enter: pte vanished, va: 0x28053000 > > syncing disks... 20 20 2 2 > done > Uptime: 21s > Automatic reboot in 15 seconds - press a key on the > console to abort > Rebooting... > Copyright (c) 1992-2001 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, > 1991, 1992, 1993, 1994 > The Regents of the University of California. > All rights reserved. > FreeBSD 4.4-RELEASE #0: Tue Sep 18 11:57:08 PDT 2001 > > murray@builder.FreeBSD.org:/usr/src/sys/compile/GENERIC > Timecounter "i8254" frequency 1193182 Hz > CPU: Pentium III/Pentium III Xeon/Celeron (999.53-MHz > 686-class CPU) > Origin = "GenuineIntel" Id = 0x68a Stepping = 10 > > Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> > real memory = 536870912 (524288K bytes) > avail memory = 518168576 (506024K bytes) > Preloaded elf kernel "kernel" at 0xc0480000. > Pentium Pro MTRR support enabled > md0: Malloc disk > Using $PIR table, 10 entries at 0xc00f5340 > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcib0: <ServerWorks host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > pcib4: <PCI to PCI bridge (vendor=1166 device=0009)> > at device 0.1 on pci0 > pci1: <PCI bus> on pcib4 > pci0: <ATI Mach64-GP graphics accelerator> at 4.0 irq > 11 > ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port > 0xde00-0xdeff mem 0xfeafb000-0xfeafbfff irq 5 at > device 5.0 on pci0 > aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/255 > SCBs > ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port > 0xd400-0xd4ff mem 0xfeafe000-0xfeafefff irq 10 at > device 5.1 on pci0 > aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/255 > SCBs > fxp0: <Intel Pro 10/100B/100+ Ethernet> port > 0xd000-0xd03f mem > 0xfe900000-0xfe9fffff,0xfeafc000-0xfeafcfff irq 9 at > device 6.0 on pci0 > fxp0: Ethernet address 00:30:48:21:d8:44 > inphy0: <i82555 10/100 media interface> on miibus0 > inphy0: 10baseT, 10baseT-FDX, 100baseTX, > 100baseTX-FDX, auto > isab0: <ServerWorks IB6566 PCI to ISA bridge> at > device 15.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <ServerWorks ROSB4 ATA33 controller> port > 0xffa0-0xffaf at device 15.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > ohci0: <OHCI (generic) USB controller> irq 0 at device > 15.2 on pci0 > ohci0: Could not map memory > device_probe_and_attach: ohci0 attach returned 6 > pcib1: <ServerWorks NB6635 3.0LE host to PCI bridge> > on motherboard > pci2: <PCI bus> on pcib1 > pcib2: <ServerWorks host to PCI bridge> on motherboard > pci3: <PCI bus> on pcib2 > pcib3: <ServerWorks host to PCI bridge> on motherboard > pci4: <PCI bus> on pcib3 > orm0: <Option ROMs> at iomem > 0xc0000-0xc7fff,0xc8000-0xc8fff,0xc9000-0xcefff on > isa0 > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 > irq 6 drq 2 on isa0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > atkbdc0: <Keyboard controller (i8042)> at port > 0x60,0x64 on isa0 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model IntelliMouse, device ID 3 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem > 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1 at port 0x2f8-0x2ff irq 3 on isa0 > sio1: type 16550A > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on > isa0 > ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE > mode > ppc0: FIFO with 16/16/8 bytes threshold > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > acd0: CDROM <CD-ROM CDU611-H> at ata0-master using > PIO4 > Mounting root from ufs:/dev/da0s1a > da0 at ahc0 bus 0 target 0 lun 0 > da0: <SEAGATE ST318404LW 0006> Fixed Direct Access > SCSI-3 device > da0: 160.000MB/s transfers (80.000MHz, offset 63, > 16bit), Tagged Queueing Enabled > da0: 17501MB (35843670 512 byte sectors: 255H 63S/T > 2231C) > WARNING: / was not properly dismounted > pid 141 (cron), uid 0: exited on signal 11 (core > dumped) > panic: pmap_enter: pte vanished, va: 0xbfbff000 > > syncing disks... 35 35 9 9 3 3 > done > Uptime: 1m53s > Automatic reboot in 15 seconds - press a key on the > console to abort > Rebooting... > Copyright (c) 1992-2001 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, > 1991, 1992, 1993, 1994 > The Regents of the University of California. > All rights reserved. > FreeBSD 4.4-RELEASE #0: Tue Sep 18 11:57:08 PDT 2001 > > murray@builder.FreeBSD.org:/usr/src/sys/compile/GENERIC > Timecounter "i8254" frequency 1193182 Hz > CPU: Pentium III/Pentium III Xeon/Celeron (999.53-MHz > 686-class CPU) > Origin = "GenuineIntel" Id = 0x68a Stepping = 10 > > Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> > real memory = 536870912 (524288K bytes) > avail memory = 518168576 (506024K bytes) > Preloaded elf kernel "kernel" at 0xc0480000. > Pentium Pro MTRR support enabled > md0: Malloc disk > Using $PIR table, 10 entries at 0xc00f5340 > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcib0: <ServerWorks host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > pcib4: <PCI to PCI bridge (vendor=1166 device=0009)> > at device 0.1 on pci0 > pci1: <PCI bus> on pcib4 > pci0: <ATI Mach64-GP graphics accelerator> at 4.0 irq > 11 > ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port > 0xde00-0xdeff mem 0xfeafb000-0xfeafbfff irq 5 at > device 5.0 on pci0 > aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/255 > SCBs > ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port > 0xd400-0xd4ff mem 0xfeafe000-0xfeafefff irq 10 at > device 5.1 on pci0 > aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/255 > SCBs > fxp0: <Intel Pro 10/100B/100+ Ethernet> port > 0xd000-0xd03f mem > 0xfe900000-0xfe9fffff,0xfeafc000-0xfeafcfff irq 9 at > device 6.0 on pci0 > fxp0: Ethernet address 00:30:48:21:d8:44 > inphy0: <i82555 10/100 media interface> on miibus0 > inphy0: 10baseT, 10baseT-FDX, 100baseTX, > 100baseTX-FDX, auto > isab0: <ServerWorks IB6566 PCI to ISA bridge> at > device 15.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <ServerWorks ROSB4 ATA33 controller> port > 0xffa0-0xffaf at device 15.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > ohci0: <OHCI (generic) USB controller> irq 0 at device > 15.2 on pci0 > ohci0: Could not map memory > device_probe_and_attach: ohci0 attach returned 6 > pcib1: <ServerWorks NB6635 3.0LE host to PCI bridge> > on motherboard > pci2: <PCI bus> on pcib1 > pcib2: <ServerWorks host to PCI bridge> on motherboard > pci3: <PCI bus> on pcib2 > pcib3: <ServerWorks host to PCI bridge> on motherboard > pci4: <PCI bus> on pcib3 > orm0: <Option ROMs> at iomem > 0xc0000-0xc7fff,0xc8000-0xc8fff,0xc9000-0xcefff on > isa0 > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 > irq 6 drq 2 on isa0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > atkbdc0: <Keyboard controller (i8042)> at port > 0x60,0x64 on isa0 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model IntelliMouse, device ID 3 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem > 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1 at port 0x2f8-0x2ff irq 3 on isa0 > sio1: type 16550A > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on > isa0 > ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE > mode > ppc0: FIFO with 16/16/8 bytes threshold > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > acd0: CDROM <CD-ROM CDU611-H> at ata0-master using > PIO4 > Mounting root from ufs:/dev/da0s1a > da0 at ahc0 bus 0 target 0 lun 0 > da0: <SEAGATE ST318404LW 0006> Fixed Direct Access > SCSI-3 device > da0: 160.000MB/s transfers (80.000MHz, offset 63, > 16bit), Tagged Queueing Enabled > da0: 17501MB (35843670 512 byte sectors: 255H 63S/T > 2231C) > WARNING: / was not properly dismounted > > > Fatal trap 12: page fault while in kernel mode > fault virtual address = 0xbfca04a8 > fault code = supervisor read, page not > present > instruction pointer = 0x8:0xc032999b > stack pointer = 0x10:0xd464e94c > frame pointer = 0x10:0xd464e95c > code segment = base 0x0, limit 0xfffff, > type 0x1b > = DPL 0, pres 1, def32 1, gran > 1 > processor eflags = interrupt enabled, resume, > IOPL = 0 > current process = 171 (su) > interrupt mask = net tty bio cam > trap number = 12 > panic: page fault > > syncing disks... 11 11 11 11 11 11 11 11 11 11 11 11 > 11 11 11 11 11 11 11 11 > giving up on 11 buffers > Uptime: 1m36s > Automatic reboot in 15 seconds - press a key on the > console to abort > Rebooting... > Copyright (c) 1992-2001 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, > 1991, 1992, 1993, 1994 > The Regents of the University of California. > All rights reserved. > FreeBSD 4.4-RELEASE #0: Tue Sep 18 11:57:08 PDT 2001 > > murray@builder.FreeBSD.org:/usr/src/sys/compile/GENERIC > Timecounter "i8254" frequency 1193182 Hz > CPU: Pentium III/Pentium III Xeon/Celeron (999.53-MHz > 686-class CPU) > Origin = "GenuineIntel" Id = 0x68a Stepping = 10 > > Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> > real memory = 536870912 (524288K bytes) > avail memory = 518168576 (506024K bytes) > Preloaded elf kernel "kernel" at 0xc0480000. > Pentium Pro MTRR support enabled > md0: Malloc disk > Using $PIR table, 10 entries at 0xc00f5340 > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcib0: <ServerWorks host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > pcib4: <PCI to PCI bridge (vendor=1166 device=0009)> > at device 0.1 on pci0 > pci1: <PCI bus> on pcib4 > pci0: <ATI Mach64-GP graphics accelerator> at 4.0 irq > 11 > ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port > 0xde00-0xdeff mem 0xfeafb000-0xfeafbfff irq 5 at > device 5.0 on pci0 > aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/255 > SCBs > ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port > 0xd400-0xd4ff mem 0xfeafe000-0xfeafefff irq 10 at > device 5.1 on pci0 > aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/255 > SCBs > fxp0: <Intel Pro 10/100B/100+ Ethernet> port > 0xd000-0xd03f mem > 0xfe900000-0xfe9fffff,0xfeafc000-0xfeafcfff irq 9 at > device 6.0 on pci0 > fxp0: Ethernet address 00:30:48:21:d8:44 > inphy0: <i82555 10/100 media interface> on miibus0 > inphy0: 10baseT, 10baseT-FDX, 100baseTX, > 100baseTX-FDX, auto > isab0: <ServerWorks IB6566 PCI to ISA bridge> at > device 15.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <ServerWorks ROSB4 ATA33 controller> port > 0xffa0-0xffaf at device 15.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > ohci0: <OHCI (generic) USB controller> irq 0 at device > 15.2 on pci0 > ohci0: Could not map memory > device_probe_and_attach: ohci0 attach returned 6 > pcib1: <ServerWorks NB6635 3.0LE host to PCI bridge> > on motherboard > pci2: <PCI bus> on pcib1 > pcib2: <ServerWorks host to PCI bridge> on motherboard > pci3: <PCI bus> on pcib2 > pcib3: <ServerWorks host to PCI bridge> on motherboard > pci4: <PCI bus> on pcib3 > orm0: <Option ROMs> at iomem > 0xc0000-0xc7fff,0xc8000-0xc8fff,0xc9000-0xcefff on > isa0 > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 > irq 6 drq 2 on isa0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > atkbdc0: <Keyboard controller (i8042)> at port > 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model Generic PS/2 mouse, device ID 0 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem > 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1 at port 0x2f8-0x2ff irq 3 on isa0 > sio1: type 16550A > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on > isa0 > ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE > mode > ppc0: FIFO with 16/16/8 bytes threshold > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > acd0: CDROM <CD-ROM CDU611-H> at ata0-master using > PIO4 > Mounting root from ufs:/dev/da0s1a > da0 at ahc0 bus 0 target 0 lun 0 > da0: <SEAGATE ST318404LW 0006> Fixed Direct Access > SCSI-3 device > da0: 160.000MB/s transfers (80.000MHz, offset 63, > 16bit), Tagged Queueing Enabled > da0: 17501MB (35843670 512 byte sectors: 255H 63S/T > 2231C) > WARNING: / was not properly dismounted > pid 209 (sh), uid 0: exited on signal 11 (core dumped) > panic: pmap_enter: pte vanished, va: 0x280af000 > > syncing disks... 12 12 > done > Uptime: 15m46s > Automatic reboot in 15 seconds - press a key on the > console to abort > Rebooting... > Copyright (c) 1992-2001 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, > 1991, 1992, 1993, 1994 > The Regents of the University of California. > All rights reserved. > FreeBSD 4.4-RELEASE #0: Tue Sep 18 11:57:08 PDT 2001 > > murray@builder.FreeBSD.org:/usr/src/sys/compile/GENERIC > Timecounter "i8254" frequency 1193182 Hz > CPU: Pentium III/Pentium III Xeon/Celeron (999.53-MHz > 686-class CPU) > Origin = "GenuineIntel" Id = 0x68a Stepping = 10 > > Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> > real memory = 536870912 (524288K bytes) > avail memory = 518168576 (506024K bytes) > Preloaded elf kernel "kernel" at 0xc0480000. > Pentium Pro MTRR support enabled > md0: Malloc disk > Using $PIR table, 10 entries at 0xc00f5340 > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcib0: <ServerWorks host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > pcib4: <PCI to PCI bridge (vendor=1166 device=0009)> > at device 0.1 on pci0 > pci1: <PCI bus> on pcib4 > pci0: <ATI Mach64-GP graphics accelerator> at 4.0 irq > 11 > ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port > 0xde00-0xdeff mem 0xfeafb000-0xfeafbfff irq 5 at > device 5.0 on pci0 > aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/255 > SCBs > ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port > 0xd400-0xd4ff mem 0xfeafe000-0xfeafefff irq 10 at > device 5.1 on pci0 > aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/255 > SCBs > fxp0: <Intel Pro 10/100B/100+ Ethernet> port > 0xd000-0xd03f mem > 0xfe900000-0xfe9fffff,0xfeafc000-0xfeafcfff irq 9 at > device 6.0 on pci0 > fxp0: Ethernet address 00:30:48:21:d8:44 > inphy0: <i82555 10/100 media interface> on miibus0 > inphy0: 10baseT, 10baseT-FDX, 100baseTX, > 100baseTX-FDX, auto > isab0: <ServerWorks IB6566 PCI to ISA bridge> at > device 15.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <ServerWorks ROSB4 ATA33 controller> port > 0xffa0-0xffaf at device 15.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > ohci0: <OHCI (generic) USB controller> irq 0 at device > 15.2 on pci0 > ohci0: Could not map memory > device_probe_and_attach: ohci0 attach returned 6 > pcib1: <ServerWorks NB6635 3.0LE host to PCI bridge> > on motherboard > pci2: <PCI bus> on pcib1 > pcib2: <ServerWorks host to PCI bridge> on motherboard > pci3: <PCI bus> on pcib2 > pcib3: <ServerWorks host to PCI bridge> on motherboard > pci4: <PCI bus> on pcib3 > orm0: <Option ROMs> at iomem > 0xc0000-0xc7fff,0xc8000-0xc8fff,0xc9000-0xcefff on > isa0 > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 > irq 6 drq 2 on isa0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > atkbdc0: <Keyboard controller (i8042)> at port > 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model Generic PS/2 mouse, device ID 0 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem > 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1 at port 0x2f8-0x2ff irq 3 on isa0 > sio1: type 16550A > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on > isa0 > ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE > mode > ppc0: FIFO with 16/16/8 bytes threshold > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > acd0: CDROM <CD-ROM CDU611-H> at ata0-master using > PIO4 > Mounting root from ufs:/dev/da0s1a > da0 at ahc0 bus 0 target 0 lun 0 > da0: <SEAGATE ST318404LW 0006> Fixed Direct Access > SCSI-3 device > da0: 160.000MB/s transfers (80.000MHz, offset 63, > 16bit), Tagged Queueing Enabled > da0: 17501MB (35843670 512 byte sectors: 255H 63S/T > 2231C) > WARNING: / was not properly dismounted > panic: pmap_enter: pte vanished, va: 0x280af000 > > syncing disks... 10 10 > done > Uptime: 6m5s > Automatic reboot in 15 seconds - press a key on the > console to abort > Rebooting... > Copyright (c) 1992-2001 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, > 1991, 1992, 1993, 1994 > The Regents of the University of California. > All rights reserved. > FreeBSD 4.4-RELEASE #0: Tue Sep 18 11:57:08 PDT 2001 > > murray@builder.FreeBSD.org:/usr/src/sys/compile/GENERIC > Timecounter "i8254" frequency 1193182 Hz > CPU: Pentium III/Pentium III Xeon/Celeron (999.53-MHz > 686-class CPU) > Origin = "GenuineIntel" Id = 0x68a Stepping = 10 > > Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> > real memory = 536870912 (524288K bytes) > avail memory = 518168576 (506024K bytes) > Preloaded elf kernel "kernel" at 0xc0480000. > Pentium Pro MTRR support enabled > md0: Malloc disk > Using $PIR table, 10 entries at 0xc00f5340 > npx0: <math processor> on motherboard > npx0: INT 16 interface > pcib0: <ServerWorks host to PCI bridge> on motherboard > pci0: <PCI bus> on pcib0 > pcib4: <PCI to PCI bridge (vendor=1166 device=0009)> > at device 0.1 on pci0 > pci1: <PCI bus> on pcib4 > pci0: <ATI Mach64-GP graphics accelerator> at 4.0 irq > 11 > ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port > 0xde00-0xdeff mem 0xfeafb000-0xfeafbfff irq 5 at > device 5.0 on pci0 > aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/255 > SCBs > ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port > 0xd400-0xd4ff mem 0xfeafe000-0xfeafefff irq 10 at > device 5.1 on pci0 > aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/255 > SCBs > fxp0: <Intel Pro 10/100B/100+ Ethernet> port > 0xd000-0xd03f mem > 0xfe900000-0xfe9fffff,0xfeafc000-0xfeafcfff irq 9 at > device 6.0 on pci0 > fxp0: Ethernet address 00:30:48:21:d8:44 > inphy0: <i82555 10/100 media interface> on miibus0 > inphy0: 10baseT, 10baseT-FDX, 100baseTX, > 100baseTX-FDX, auto > isab0: <ServerWorks IB6566 PCI to ISA bridge> at > device 15.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <ServerWorks ROSB4 ATA33 controller> port > 0xffa0-0xffaf at device 15.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > ohci0: <OHCI (generic) USB controller> irq 0 at device > 15.2 on pci0 > ohci0: Could not map memory > device_probe_and_attach: ohci0 attach returned 6 > pcib1: <ServerWorks NB6635 3.0LE host to PCI bridge> > on motherboard > pci2: <PCI bus> on pcib1 > pcib2: <ServerWorks host to PCI bridge> on motherboard > pci3: <PCI bus> on pcib2 > pcib3: <ServerWorks host to PCI bridge> on motherboard > pci4: <PCI bus> on pcib3 > orm0: <Option ROMs> at iomem > 0xc0000-0xc7fff,0xc8000-0xc8fff,0xc9000-0xcefff on > isa0 > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 > irq 6 drq 2 on isa0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > atkbdc0: <Keyboard controller (i8042)> at port > 0x60,0x64 on isa0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model Generic PS/2 mouse, device ID 0 > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem > 0xa0000-0xbffff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A > sio1 at port 0x2f8-0x2ff irq 3 on isa0 > sio1: type 16550A > ppc0: <Parallel port> at port 0x378-0x37f irq 7 on > isa0 > ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE > mode > ppc0: FIFO with 16/16/8 bytes threshold > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > acd0: CDROM <CD-ROM CDU611-H> at ata0-master using > PIO4 > Mounting root from ufs:/dev/da0s1a > da0 at ahc0 bus 0 target 0 lun 0 > da0: <SEAGATE ST318404LW 0006> Fixed Direct Access > SCSI-3 device > da0: 160.000MB/s transfers (80.000MHz, offset 63, > 16bit), Tagged Queueing Enabled > da0: 17501MB (35843670 512 byte sectors: 255H 63S/T > 2231C) > WARNING: / was not properly dismounted > > > __________________________________________________ > Do You Yahoo!? > Send your FREE holiday greetings online! > http://greetings.yahoo.com > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-questions" in the body of the message > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.GSO.4.21.0112271729180.16111-100000>