Date: Fri, 24 Jan 2003 11:54:41 +0000 From: Steven Haywood <freebsd@keybaud.org> To: Thomas Moestl <tmoestl@gmx.net> Cc: current@freebsd.org Subject: Re: kernel panic with today's CURRENT on sparc64 at boot Message-ID: <20030124115441.GB11545@keybaud.org> In-Reply-To: <20030122195951.GA16868@crow.dom2ip.de> References: <20030121173342.GA15661@keybaud.org> <20030122195951.GA16868@crow.dom2ip.de>
next in thread | previous in thread | raw e-mail | index | archive | help
On Wed, Jan 22, 2003 at 08:59:51PM +0100, Thomas Moestl wrote:
> On Tue, 2003/01/21 at 17:33:42 +0000, freebsd@keybaud.org wrote:
> > Hi
> >
> > cvsup'd to . today on an E220R, single CPU with two Symbios scsi cards.
> > Box had been running fine with RC3, but would not boot with -CURRENT
> > kernel:
> >
> > Current:
> >
> > hme4: Ethernet address: 08:00:20:b7:ef:44
> > miibus4: <MII bus> on hme4
> > ukphy3: <Generic IEEE 802.3u media interface> on miibus4
> > ukphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> > sym0: <875> port 0x1000-0x10ff mem 0x1090a000-0x1090afff,0x10908000-0x109080ff i
> > rq 32 at device 3.0 on pci0
> > panic: trap: fast data access mmu miss
> > cpuid = 0;
> > Debugger("panic")
> > Stopped at Debugger+0x1c: ta %xcc, 1
>
> Can you please cvsup again to pick up some changes that were made
> yesterday and try again?
>
Hi there
Well, after a panic last night in IPFW on -RELEASE, I decided to try
-CURRENT again.
I just CVSUP'd, built kernel and rebooted.
Here's what happened:
FreeBSD/sparc64 bootstrap loader, Revision 1.0
(root@ns1.hurricaneseye.com, Wed Jan 22 11:31:27 GMT 2003)
bootpath="/pci@1f,4000/scsi@3/disk@0,0:a"
Loading /boot/defaults/loader.conf
/boot/kernel/kernel data=0x2cc308+0xe4178 syms=[0x8+0x44310+0x8+0x34e6f]
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
nothing to autoload yet.
jumping to kernel entry at 0xc0038000.
stray vector interrupt 2029
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights
reserved.
FreeBSD 5.0-CURRENT #7: Fri Jan 24 10:36:24 GMT 2003
root@ns1.hurricaneseye.com:/usr/obj/usr/src/sys/NS
Preloaded elf kernel "/boot/kernel/kernel" at 0xc042c000.
Timecounter "tick" frequency 450026203 Hz
cpu0: Sun Microsystems UltraSparc-II Processor (450.03 MHz
CPU)
Model: SUNW,Ultra-60
Initializing GEOMetry subsystem
nexus0: <OpenFirmware Nexus device>
pcib0: <U2P UPA-PCI bridge> on nexus0
pcib0: Psycho, impl 0, version 4, ign 0x7c0
initialializing counter-timer
Timecounter "counter-timer" frequency 1000000 Hz
DVMA map: 0xfe000000 to 0xffffffff
device 0/1/0: latency timer 0 -> 82
pcib0: ofw_pci_init: no interrupt mapping found for 0/1/0
(preset 128)
device 0/1/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 0/1/1 to 33 (preset
was 0)
device 0/3/0: latency timer 0 -> 140
pcib0: ofw_pci_init: mapping intr for 0/3/0 to 32 (preset
was 0)
device 0/3/1: latency timer 0 -> 140
pcib0: ofw_pci_init: mapping intr for 0/3/1 to 38 (preset
was 0)
PCI-PCI bridge at 0/2/0: setting bus #s to 0/1/1
pcib0: ofw_pci_init: descending to subordinate PCI bus
device 1/0/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/0/0 to 16 (preset
was 0)
device 1/0/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/0/1 to 17 (preset
was 0)
device 1/1/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/1/0 to 17 (preset
was 0)
device 1/1/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/1/1 to 18 (preset
was 0)
device 1/2/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/2/0 to 18 (preset
was 0)
device 1/2/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/2/1 to 19 (preset
was 0)
device 1/3/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/3/0 to 19 (preset
was 0)
device 1/3/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/3/1 to 16 (preset
was 0)
PCI-PCI bridge at 0/4/0: setting bus #s to 0/2/2
pcib0: ofw_pci_init: descending to subordinate PCI bus
device 2/0/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/0/0 to 24 (preset
was 0)
device 2/0/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/0/1 to 25 (preset
was 0)
device 2/1/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/1/0 to 25 (preset
was 0)
device 2/1/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/1/1 to 26 (preset
was 0)
device 2/2/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/2/0 to 26 (preset
was 0)
device 2/2/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/2/1 to 27 (preset
was 0)
device 2/3/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/3/0 to 27 (preset
was 0)
device 2/3/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/3/1 to 24 (preset
was 0)
device 0/5/0: latency timer 0 -> 1584
pcib0: ofw_pci_init: mapping intr for 0/5/0 to 28 (preset
was 0)
pci0: <PCI bus> on pcib0
ebus0: revision 0x01
ebus0: <PCI-EBus2 bridge> mem
0x71000000-0x717fffff,0x70000000-0x70ffffff at dev
ice 1.0 on pci0
ebus0: <auxio> addr
0x140072f000-0x140072f003,0x140072c000-0x140072c003,0x140072
a000-0x140072a003,0x1400728000-0x1400728003,0x1400726000-0x1400726003
(no driver
attached)
ebus0: <power> addr 0x1400724000-0x1400724003 (no driver
attached)
ebus0: <SUNW,pll> addr 0x1400504000-0x1400504002 (no driver
attached)
ebus0: <sc> addr 0x1400500000-0x1400500007 (no driver
attached)
ebus0: <se> addr 0x1400400000-0x140040007f irq 43 (no
driver attached)
ebus0: <su> addr 0x14003083f8-0x14003083ff irq 41 (no
driver attached)
ebus0: <su> addr 0x14003062f8-0x14003062ff irq 42 (no
driver attached)
ebus0: <ecpp> addr
0x1400700000-0x140070000f,0x1400300398-0x1400300399,0x1400304
3bc-0x14003043cb irq 34 (no driver attached)
ebus0: <fdthree> addr
0x1400720000-0x1400720003,0x1400706000-0x140070600f,0x1400
3023f0-0x14003023f7 irq 39 (no driver attached)
eeprom0: <EBus EEPROM/clock> addr 0x1400000000-0x1400001fff
on ebus0
eeprom0: model mk48t59
eeprom0: hostid 80b7ef44
ebus0: <flashprom> addr 0x1000000000-0x10000fffff (no
driver attached)
hme0: <Sun HME 10/100 Ethernet> mem 0x10900000-0x10907fff
irq 33 at device 1.1 o
n pci0
hme0: Ethernet address: 08:00:20:b7:ef:44
miibus0: <MII bus> on hme0
qsphy0: <QS6612 10/100 media interface> on miibus0
qsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
pcib1: <PCI-PCI bridge> at device 2.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <bridge, PCI-unknown> at device 0.0 (no driver
attached)
hme1: <Sun HME 10/100 Ethernet> mem 0x2800000-0x2807fff irq
17 at device 0.1 on
pci1
hme1: Ethernet address: 08:00:20:b7:ef:44
miibus1: <MII bus> on hme1
ukphy0: <Generic IEEE 802.3u media interface> on miibus1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
pci1: <bridge, PCI-unknown> at device 1.0 (no driver
attached)
hme2: <Sun HME 10/100 Ethernet> mem 0x4800000-0x4807fff irq
18 at device 1.1 on
pci1
hme2: Ethernet address: 08:00:20:b7:ef:44
miibus2: <MII bus> on hme2
ukphy1: <Generic IEEE 802.3u media interface> on miibus2
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
pci1: <bridge, PCI-unknown> at device 2.0 (no driver
attached)
hme3: <Sun HME 10/100 Ethernet> mem 0x6800000-0x6807fff irq
19 at device 2.1 on
pci1
hme3: Ethernet address: 08:00:20:b7:ef:44
miibus3: <MII bus> on hme3
ukphy2: <Generic IEEE 802.3u media interface> on miibus3
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
pci1: <bridge, PCI-unknown> at device 3.0 (no driver
attached)
hme4: <Sun HME 10/100 Ethernet> mem 0x8800000-0x8807fff irq
16 at device 3.1 on
pci1
hme4: Ethernet address: 08:00:20:b7:ef:44
miibus4: <MII bus> on hme4
ukphy3: <Generic IEEE 802.3u media interface> on miibus4
ukphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
sym0: <875> port 0x1000-0x10ff mem
0x1090a000-0x1090afff,0x10908000-0x109080ff i
rq 32 at device 3.0 on pci0
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym1: <875> port 0x1400-0x14ff mem
0x1090e000-0x1090efff,0x1090c000-0x1090c0ff i
rq 38 at device 3.1 on pci0
sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
pcib2: <PCI-PCI bridge> at device 4.0 on pci0
pci2: <PCI bus> on pcib2
pci2: <bridge, PCI-unknown> at device 0.0 (no driver
attached)
hme5: <Sun HME 10/100 Ethernet> mem 0xa800000-0xa807fff irq
25 at device 0.1 on
pci2
hme5: Ethernet address: 08:00:20:b7:ef:44
miibus5: <MII bus> on hme5
ukphy4: <Generic IEEE 802.3u media interface> on miibus5
ukphy4: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
pci2: <bridge, PCI-unknown> at device 1.0 (no driver
attached)
hme6: <Sun HME 10/100 Ethernet> mem 0xc800000-0xc807fff irq
26 at device 1.1 on
pci2
hme6: DMA buffer map load error 12
hme6: could not be configured
device_probe_and_attach: hme6 attach returned 6
pci2: <bridge, PCI-unknown> at device 2.0 (no driver
attached)
hme6: <Sun HME 10/100 Ethernet> mem 0xe800000-0xe807fff irq
27 at device 2.1 on
pci2
hme6: DMA buffer map load error 12
hme6: could not be configured
device_probe_and_attach: hme6 attach returned 6
pci2: <bridge, PCI-unknown> at device 3.0 (no driver
attached)
pci2: <bridge, PCI-unknown> at device 3.0 (no driver
attached)
n pci2
hme6: DMA buffer map load error 12
hme6: could not be configured
device_probe_and_attach: hme6 attach returned 6
pci0: <display> at device 5.0 (no driver attached)
pcib3: <U2P UPA-PCI bridge> on nexus0
pcib3: Psycho, impl 0, version 4, ign 0x7c0
pci3: <PCI bus> on pcib3
Timecounters tick every 10.000 msec
ipfw2 initialized, divert disabled, rule-based forwarding
enabled, default to de
ny, logging limited to 100 packets/entry by default
Waiting 5 seconds for SCSI devices to settle
da0 at sym0 bus 0 target 1 lun 0
da0: <FUJITSU MAG3091L SUN9.0G 1111> Fixed Direct Access
SCSI-2 device
da0: 40.000MB/s transfers (20.000MHz, offset 16, 16bit),
Tagged Queueing Enabled
da0: 8637MB (17689267 512 byte sectors: 255H 63S/T 1101C)
Mounting root from ufs:/dev/da0a
exec /sbin/init: error 8
init: not found in path
/sbin/init:/sbin/oinit:/sbin/init.bak:/stand/sysinstall
panic: no init
cpuid = 0;
Debugger("panic")
Stopped at Debugger+0x1c: ta %xcc, 1
RELEASE looks like this:
OK boot kernel.old
/boot/kernel.old/kernel data=0x2cb808+0xe4778
syms=[0x8+0x44118+0x8+0x349e9]
nothing to autoload yet.
jumping to kernel entry at 0xc0038000.
stray vector interrupt 2029
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights
reserved.
FreeBSD 5.0-RELEASE #6: Wed Jan 22 15:55:57 GMT 2003
root@ns1.hurricaneseye.com:/usr/obj/usr/src/sys/NS
Preloaded elf kernel "/boot/kernel.old/kernel" at
0xc042c000.
Timecounter "tick" frequency 450024890 Hz
cpu0: Sun Microsystems UltraSparc-II Processor (450.02 MHz
CPU)
Model: SUNW,Ultra-60
Initializing GEOMetry subsystem
nexus0: <OpenFirmware Nexus device>
pcib0: <U2P UPA-PCI bridge> on nexus0
pcib0: Psycho, impl 0, version 4, ign 7c0 initialializing
counter-timer
Timecounter "counter-timer" frequency 1000000 Hz
DVMA map: 0xfe000000 to 0xffffffff
device 0/1/0: latency timer 0 -> 82
pcib0: ofw_pci_init: no interrupt mapping found for 0/1/0
(preset 128)
device 0/1/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 0/1/1 to 33 (preset
was 0)
device 0/3/0: latency timer 0 -> 140
pcib0: ofw_pci_init: mapping intr for 0/3/0 to 32 (preset
was 0)
device 0/3/1: latency timer 0 -> 140
pcib0: ofw_pci_init: mapping intr for 0/3/1 to 38 (preset
was 0)
PCI-PCI bridge at 0/2/0: setting bus #s to 0/1/1
pcib0: ofw_pci_init: descending to subordinate PCI bus
device 1/0/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/0/0 to 16 (preset
was 0)
device 1/0/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/0/1 to 17 (preset
was 0)
device 1/1/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/1/0 to 17 (preset
was 0)
device 1/1/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/1/1 to 18 (preset
was 0)
device 1/2/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/2/0 to 18 (preset
was 0)
device 1/2/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/2/1 to 19 (preset
was 0)
device 1/3/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/3/0 to 19 (preset
was 0)
device 1/3/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 1/3/1 to 16 (preset
was 0)
PCI-PCI bridge at 0/4/0: setting bus #s to 0/2/2
pcib0: ofw_pci_init: descending to subordinate PCI bus
device 2/0/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/0/0 to 24 (preset
was 0)
device 2/0/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/0/1 to 25 (preset
was 0)
device 2/1/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/1/0 to 25 (preset
was 0)
device 2/1/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/1/1 to 26 (preset
was 0)
device 2/2/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/2/0 to 26 (preset
was 0)
device 2/2/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/2/1 to 27 (preset
was 0)
device 2/3/0: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/3/0 to 27 (preset
was 0)
device 2/3/1: latency timer 0 -> 82
pcib0: ofw_pci_init: mapping intr for 2/3/1 to 24 (preset
was 0)
device 0/5/0: latency timer 0 -> 1584
pcib0: ofw_pci_init: mapping intr for 0/5/0 to 28 (preset
was 0)
pci0: <PCI bus> on pcib0
ebus0: revision 0x01
ebus0: <PCI-EBus2 bridge> mem
0x71000000-0x717fffff,0x70000000-0x70ffffff at dev
ice 1.0 on pci0
ebus0: <auxio> addr
0x140072f000-0x140072f003,0x140072c000-0x140072c003,0x140072
a000-0x140072a003,0x1400728000-0x1400728003,0x1400726000-0x1400726003
(no driver
attached)
ebus0: <power> addr 0x1400724000-0x1400724003 (no driver
attached)
ebus0: <SUNW,pll> addr 0x1400504000-0x1400504002 (no driver
attached)
ebus0: <sc> addr 0x1400500000-0x1400500007 (no driver
attached)
ebus0: <se> addr 0x1400400000-0x140040007f irq 43 (no
driver attached)
ebus0: <su> addr 0x14003083f8-0x14003083ff irq 41 (no
driver attached)
ebus0: <su> addr 0x14003062f8-0x14003062ff irq 42 (no
driver attached)
ebus0: <ecpp> addr
0x1400700000-0x140070000f,0x1400300398-0x1400300399,0x1400304
3bc-0x14003043cb irq 34 (no driver attached)
ebus0: <fdthree> addr
0x1400720000-0x1400720003,0x1400706000-0x140070600f,0x1400
3023f0-0x14003023f7 irq 39 (no driver attached)
eeprom0: <EBus EEPROM/clock> addr 0x1400000000-0x1400001fff
on ebus0
eeprom0: model mk48t59
eeprom0: hostid 80b7ef44
ebus0: <flashprom> addr 0x1000000000-0x10000fffff (no
driver attached)
hme0: <Sun HME 10/100 Ethernet> mem 0x10900000-0x10907fff
irq 33 at device 1.1 o
n pci0
hme0: Ethernet address: 08:00:20:b7:ef:44
miibus0: <MII bus> on hme0
qsphy0: <QS6612 10/100 media interface> on miibus0
qsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
pcib1: <PCI-PCI bridge> at device 2.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <bridge, PCI-unknown> at device 0.0 (no driver
attached)
hme1: <Sun HME 10/100 Ethernet> mem 0x2800000-0x2807fff irq
17 at device 0.1 on
pci1
hme1: Ethernet address: 08:00:20:b7:ef:44
miibus1: <MII bus> on hme1
ukphy0: <Generic IEEE 802.3u media interface> on miibus1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
pci1: <bridge, PCI-unknown> at device 1.0 (no driver
attached)
hme2: <Sun HME 10/100 Ethernet> mem 0x4800000-0x4807fff irq
18 at device 1.1 on
pci1
hme2: Ethernet address: 08:00:20:b7:ef:44
miibus2: <MII bus> on hme2
ukphy1: <Generic IEEE 802.3u media interface> on miibus2
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
pci1: <bridge, PCI-unknown> at device 2.0 (no driver
attached)
hme3: <Sun HME 10/100 Ethernet> mem 0x6800000-0x6807fff irq
19 at device 2.1 on
pci1
hme3: Ethernet address: 08:00:20:b7:ef:44
miibus3: <MII bus> on hme3
ukphy2: <Generic IEEE 802.3u media interface> on miibus3
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
pci1: <bridge, PCI-unknown> at device 3.0 (no driver
attached)
hme4: <Sun HME 10/100 Ethernet> mem 0x8800000-0x8807fff irq
16 at device 3.1 on
pci1
hme4: Ethernet address: 08:00:20:b7:ef:44
miibus4: <MII bus> on hme4
ukphy3: <Generic IEEE 802.3u media interface> on miibus4
ukphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
sym0: <875> port 0x1000-0x10ff mem
0x1090a000-0x1090afff,0x10908000-0x109080ff i
rq 32 at device 3.0 on pci0
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym1: <875> port 0x1400-0x14ff mem
0x1090e000-0x1090efff,0x1090c000-0x1090c0ff i
rq 38 at device 3.1 on pci0
sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
pcib2: <PCI-PCI bridge> at device 4.0 on pci0
pci2: <PCI bus> on pcib2
pci2: <bridge, PCI-unknown> at device 0.0 (no driver
attached)
hme5: <Sun HME 10/100 Ethernet> mem 0xa800000-0xa807fff irq
25 at device 0.1 on
pci2
hme5: Ethernet address: 08:00:20:b7:ef:44
miibus5: <MII bus> on hme5
ukphy4: <Generic IEEE 802.3u media interface> on miibus5
ukphy4: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
pci2: <bridge, PCI-unknown> at device 1.0 (no driver
attached)
hme6: <Sun HME 10/100 Ethernet> mem 0xc800000-0xc807fff irq
26 at device 1.1 on
pci2
hme6: Ethernet address: 08:00:20:b7:ef:44
miibus6: <MII bus> on hme6
ukphy5: <Generic IEEE 802.3u media interface> on miibus6
ukphy5: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
pci2: <bridge, PCI-unknown> at device 2.0 (no driver
attached)
hme7: <Sun HME 10/100 Ethernet> mem 0xe800000-0xe807fff irq
27 at device 2.1 on
pci2
hme7: Ethernet address: 08:00:20:b7:ef:44
miibus7: <MII bus> on hme7
ukphy6: <Generic IEEE 802.3u media interface> on miibus7
ukphy6: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
pci2: <bridge, PCI-unknown> at device 3.0 (no driver
attached)
hme8: <Sun HME 10/100 Ethernet> mem 0x10800000-0x10807fff
irq 24 at device 3.1 o
n pci2
hme8: Ethernet address: 08:00:20:b7:ef:44
miibus8: <MII bus> on hme8
ukphy7: <Generic IEEE 802.3u media interface> on miibus8
ukphy7: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
auto
pci0: <display> at device 5.0 (no driver attached)
pcib3: <U2P UPA-PCI bridge> on nexus0
pcib3: Psycho, impl 0, version 4, ign 7c0 pci3: <PCI bus>
on pcib3
Timecounters tick every 10.000 msec
ipfw2 initialized, divert disabled, rule-based forwarding
enabled, default to de
ny, logging limited to 100 packets/entry by default
Waiting 5 seconds for SCSI devices to settle
cd0 at sym0 bus 0 target 6 lun 0
cd0: <TOSHIBA XM6201TASUN32XCD 1103> Removable CD-ROM
SCSI-2 device
cd0: 10.000MB/s transfers (10.000MHz, offset 16)
cd0: cd present [420504 x 512 byte records]
da1 at sym0 bus 0 target 1 lun 0
da1: <FUJITSU MAG3091L SUN9.0G 1111> Fixed Direct Access
SCSI-2 device
da1: 40.000MB/s transfers (20.000MHz, offset 16, 16bit),
Tagged Queueing Enabled
da1: 8637MB (17689267 512 byte sectors: 255H 63S/T 1101C)
da0 at sym0 bus 0 target 0 lun 0
da0: <SEAGATE ST318404LSUN18G 8507> Fixed Direct Access
SCSI-3 device
da0: 40.000MB/s transfers (20.000MHz, offset 16, 16bit),
Tagged Queueing Enabled
da0: 17274MB (35378533 512 byte sectors: 255H 63S/T 2202C)
Mounting root from ufs:/dev/da0a
hw.bus.devctl_disable: 0 -> 1
Loading configuration files.
Entropy harvesting: interrupts ethernet point_to_point.
swapon: adding /dev/da0b as swap device
Starting file system checks:
/dev/da0a: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da0a: clean, 158093 free (373 frags, 19715 blocks,
0.2% fragmentation)
/dev/da0e: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da0e: clean, 199275 free (107 frags, 24896 blocks,
0.1% fragmentation)
/dev/da0f: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da0f: clean, 6784448 free (24928 frags, 844940 blocks,
0.3% fragmentation)
/dev/da0d: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da0d: clean, 513279 free (95 frags, 64148 blocks, 0.0%
fragmentation)
security.bsd.see_other_uids: 1 -> 0
net.inet.tcp.blackhole: 0 -> 2
net.inet.udp.blackhole: 0 -> 1
net.inet.ip.rtexpire: 3600 -> 600
Doing initial network setup: hostname.
So it looks like it doesn't initialize SCSI stuff properly. as well as
some DMA problems with the 2nd QFE card. For the record, I recompiled
with the SCSI delay set to 15000, it made no difference
Cheers
Steven
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20030124115441.GB11545>