Date: Wed, 27 Nov 2002 21:40:26 -0800 From: Juli Mallett <jmallett@FreeBSD.org> To: Mitsuru IWASAKI <iwasaki@jp.FreeBSD.org> Cc: acpi-jp@jp.FreeBSD.org, current@freebsd.org Subject: Re: Call for testers: acpica-unix-20021122 (was Re: ACPI errors and then panic - fixed!) Message-ID: <20021127214026.A82346@FreeBSD.org> In-Reply-To: <20021128.133813.08399326.iwasaki@jp.FreeBSD.org>; from iwasaki@jp.FreeBSD.org on Thu, Nov 28, 2002 at 01:38:13PM %2B0900 References: <20021128.133813.08399326.iwasaki@jp.FreeBSD.org>
next in thread | previous in thread | raw e-mail | index | archive | help
* De: Mitsuru IWASAKI <iwasaki@jp.FreeBSD.org> [ Data: 2002-11-27 ] [ Subjecte: Call for testers: acpica-unix-20021122 (was Re: ACPI errors and then panic - fixed!) ] > The patches against today's CURRENT at: > http://people.freebsd.org/~iwasaki/acpi/acpica-20021118-20021122-test20021128.diff > > Please try this if you have problems about ACPI interpreter or GPE > initialization. Iwasaki-san! This works for me, thanks very much for helping keep us all up to date, and making it possible to get the issues resolved. Here's a dmesg from my laptop, now that ACPI works. %%% dmesg-YAY Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.0-CURRENT #48: Wed Nov 27 23:30:47 CST 2002 jmallett@luna.flata.nu:/usr/src/sys/i386/compile/LUNA Preloaded elf kernel "/boot/kernel/kernel" at 0xc0547000. Timecounter "i8254" frequency 1193182 Hz Timecounter "TSC" frequency 474889174 Hz CPU: AMD-K6(tm) 3D processor (474.89-MHz 586-class CPU) Origin = "AuthenticAMD" Id = 0x58c Stepping = 12 Features=0x8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX> AMD Features=0xffffffff80000800<SYSCALL,3DNow!> real memory = 67043328 (63 MB) avail memory = 59457536 (56 MB) Security policy loaded: TrustedBSD MAC/None (trustedbsd_mac_none) Initializing GEOMetry subsystem K6-family MTRR support enabled (2 registers) acpi0: <PTLTD RSDT > on motherboard ACPI-0628: *** Info: GPE Block0 defined as GPE0 to GPE15 Using $PIR table, 6 entries at 0xc00fdf60 acpi0: power button is handled as a fixed feature programming model. Timecounter "ACPI-fast" frequency 3579545 Hz acpi_timer0: <32-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_tz0: <thermal zone> on acpi0 acpi_lid0: <Control Method Lid Switch> on acpi0 acpi_cmbat0: <Control method Battery> on acpi0 acpi_acad0: <AC adapter> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 ---- initial configuration ------------------------ \\_SB_.PCI0.ISA_.LNK1 irq 11: [ 3 4 5 6 7 9 10 11 14 15] low,level,sharable 0.4.0 \\_SB_.PCI0.ISA_.LNK2 irq 11: [ 3 4 5 6 7 9 10 11 14 15] low,level,sharable 0.4.1 \\_SB_.PCI0.ISA_.LNK5 irq 9: [ 3 4 5 6 7 9 10 11 14 15] low,level,sharable 0.19.0 \\_SB_.PCI0.ISA_.LNK3 irq 5: [ 3 4 5 6 7 9 10 11 14 15] low,level,sharable 0.8.0 \\_SB_.PCI0.ISA_.LNK4 irq 10: [ 3 4 5 6 7 10 11 14 15] low,level,sharable 0.16.0 ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- \\_SB_.PCI0.ISA_.LNK1 irq 11: [ 3 4 5 6 7 9 10 11 14 15] low,level,sharable 0.4.0 \\_SB_.PCI0.ISA_.LNK2 irq 11: [ 3 4 5 6 7 9 10 11 14 15] low,level,sharable 0.4.1 \\_SB_.PCI0.ISA_.LNK5 irq 9: [ 3 4 5 6 7 9 10 11 14 15] low,level,sharable 0.19.0 \\_SB_.PCI0.ISA_.LNK3 irq 5: [ 3 4 5 6 7 9 10 11 14 15] low,level,sharable 0.8.0 \\_SB_.PCI0.ISA_.LNK4 irq 10: [ 3 4 5 6 7 10 11 14 15] low,level,sharable 0.16.0 pci0: <ACPI PCI bus> on pcib0 agp0: <Ali M1541 host to AGP bridge> mem 0xe0000000-0xe3ffffff at device 0.0 on pci0 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 ---- initial configuration ------------------------ \\_SB_.PCI0.ISA_.LNK1 irq 11: [ 3 4 5 6 7 9 10 11 14 15] low,level,sharable 1.0.0 ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- \\_SB_.PCI0.ISA_.LNK1 irq 11: [ 3 4 5 6 7 9 10 11 14 15] low,level,sharable 1.0.0 pci1: <ACPI PCI bus> on pcib1 pci1: <display, VGA> at device 0.0 (no driver attached) cbb0: <TI1225 PCI-CardBus Bridge> mem 0x88000000-0x88000fff irq 11 at device 4.0 on pci0 cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 cbb1: <TI1225 PCI-CardBus Bridge> mem 0x88001000-0x88001fff irq 11 at device 4.1 on pci0 cardbus1: <CardBus bus> on cbb1 pccard1: <16-bit PCCard bus> on cbb1 isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 pcm0: <Crystal Semiconductor CS4281> mem 0xfedf0000-0xfedfffff,0xfeddf000-0xfeddffff irq 5 at device 8.0 on pci0 atapci0: <AcerLabs Aladdin ATA33 controller> port 0xfcf0-0xfcff at device 15.0 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pci0: <simple comms> at device 16.0 (no driver attached) pci0: <bridge, PCI-unknown> at device 17.0 (no driver attached) ohci0: <AcerLabs M5237 (Aladdin-V) USB controller> mem 0xfedde000-0xfeddefff irq 9 at device 19.0 on pci0 usb0: OHCI version 1.0, legacy support usb0: <AcerLabs M5237 (Aladdin-V) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: AcerLabs OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered speaker0 port 0x61 on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 npx0: <math processor> on motherboard npx0: INT 16 interface orm0: <Option ROM> at iomem 0xc0000-0xcb7ff on isa0 ppc0: parallel port not found. sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0 at vga0 Timecounters tick every 10.000 msec acpi_cpu: CPU throttling enabled, 8 steps from 100% to 12.5% wi0: <WaveLAN/IEEE> at port 0x100-0x13f irq 11 function 0 config 1 on pccard1 wi0: 802.11 address: 00:30:ab:14:0a:60 wi0: using RF:PRISM2 MAC:HFA3841 CARD:HWB3163-SST-flash wi0: Intersil Firmware: Primary 0.03.00, Station 1.03.04 ad0: 4126MB <TOSHIBA MK4313MAT> [8944/15/63] at ata0-master UDMA33 stray irq 7 Mounting root from ufs:/dev/ad0s1a %%% Thanks, juli! -- Juli Mallett <jmallett@FreeBSD.org> OpenDarwin, Mono, FreeBSD Developer. ircd-hybrid Developer, EFnet addict. FreeBSD on MIPS-Anything on FreeBSD. To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20021127214026.A82346>