Date: Fri, 24 Nov 2000 10:05:10 -0600 From: Drew Sanford <drew@planetwe.com> To: stable@freebsd.org Subject: Update - 4.2 install hangs while booting Message-ID: <3A1E91B6.3040807@planetwe.com>
next in thread | raw e-mail | index | archive | help
I have had a chance to play with 4.2 now, having gotten it installed,
and narrowed down some of the hardware problems that it could be. Here's
a system rundown:
Asus A7V rev 1.02; Duron 800
SBLive
NetGear FA 310Tx
45 GB ATA100 IBM Deskstar as Master on Primary ATA100
32x ATAPI cd rom drive as Slave on Primary UDM33/66
When I boot the system with the Parallel port enabled in the bios,
regardless of the specified IRQ or IO port in bios, I get this:
ppc0: <Parallel Port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: IEEE1284 device found /NIBBLE/ECP
Probing for PnP devices on ppbus0:
ppbus0: <HEWLETT-PACKARD DESKJET 810C> MLC, PCL, PML
lpt0: <Printer> on ppbus0
lpt0: Interupt-driven port
ppi0: <Parallel I/O> on ppbus0
and here the system will hang, for at least 25 minutes. Beyond that I
figured it was usless to wait and see if anything would happen, and I
lost pateince besides. Here's the dmesg output for the same system, same
kernel, but with the parallel port disabled in the bios:
lauasanf@colossus(~)$ dmesg
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.2-RELEASE #3: Thu Nov 23 20:51:12 CST 2000
lauasanf@colossus.cotharyus.net:/usr/src/sys/compile/Colossus
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 807193223 Hz
CPU: AMD Athlon(tm) Processor (807.19-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x630 Stepping = 0
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
AMD Features=0xc0440000<<b18>,AMIE,DSP,3DNow!>
real memory = 268353536 (262064K bytes)
avail memory = 257773568 (251732K bytes)
Preloaded elf kernel "kernel" at 0xc037c000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib2: <PCI to PCI bridge (vendor=1106 device=8305)> at device 1.0 on pci0
pci1: <PCI bus> on pcib2
pci1: <Matrox MGA G400 AGP graphics accelerator> at 0.0 irq 11
isab0: <VIA 82C686 PCI-ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA66 controller> port 0xd800-0xd80f at device 4.1
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 5 at device
4.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xd000-0xd01f irq 5 at device
4.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2: ALCOR Generic USB Hub, class 9/0, rev 1.10/1.00, addr 2
uhub2: 4 ports with 4 removable, self powered
dc0: <82c169 PNIC 10/100BaseTX> port 0xa400-0xa4ff mem
0xe0000000-0xe00000ff irq 7 at device 10.0 on pci0
dc0: Ethernet address: 00:a0:cc:40:93:80
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcm0: <Creative EMU10K1> port 0xa000-0xa01f irq 10 at device 11.0 on pci0
atapci1: <Promise ATA100 controller> port
0x8000-0x803f,0x8400-0x8403,0x8800-0x8807,0x9000-0x9003,0x9400-0x9407
mem 0xdf800000-0xdf81ffff irq 10 at device 17.0 on pci0
ata2: at 0x9400 on atapci1
pcib1: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib1
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: parallel port not found.
ata1-slave: ata_command: timeout waiting for intr
ata1-slave: identify failed
ata1-master: ata_command: timeout waiting for intr
ata1-master: identify failed
ad4: 43979MB <IBM-DTLA-307045> [89355/16/63] at ata2-master UDMA100
acd0: CDROM <CRD-8322B> at ata0-slave using PIO4
Mounting root from ufs:/dev/ad4s1a
Despite the ata errors, everything appears to work fine (including the
SBLive!). The system is blazing fast (of course the system this is
replacing was a dual 233MMX) and appears to be rock solid thus far. A
make -j10 buildworld from X while running a make install on the nedit
and xmms ports didn't phase it. The config for the kernel is included
below. If anyone can come up with any reasons for the problem with the
parallel port, and a solution that doesn't call for disabling the ATA100
controler I'll give it a shot.
machine i386
#cpu I586_CPU
cpu I686_CPU
ident Colossus
maxusers 32
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug
symbols
options INET #InterNETworking
options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep
this!]
options SOFTUPDATES #Enable FFS soft updates support
options NFS #Network Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root, CD9660
required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP
THIS!]
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor Kernel
#options APIC_IO # Symmetric (APIC) I/O
device isa
device eisa
device pci
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
options ATA_STATIC_ID #Static device numbering
#options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI devices
# SCSI devices needed for USB storage support
device scbus # SCSI bus (required)
device da # Direct Access (disks)
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt
console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT
lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device sio2 at isa? disable port IO_COM3 irq 5
device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# PCI Ethernet NICs.
device de # DEC/Intel DC21x4x (``Tulip'')
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
device dc # DEC/Intel 21143 and various workalikes
# Pseudo devices - the number indicates how many units to allocated.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif 4 # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# SB Live support
device pcm
# USB support
device uhci # UHCI PCI->USB interface
device ohci # OHCI PCI->USB interface
device usb # USB Bus (required)
device ugen # Generic
device uhid # "Human Interface Devices"
device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus and da
device ums # Mouse
device uscanner # Scanners
# USB Ethernet, requires mii
device aue # ADMtek USB ethernet
device cue # CATC USB ethernet
device kue # Kawasaki LSI USB ethernet
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3A1E91B6.3040807>