Date: Wed, 7 Nov 2007 19:14:07 +0900 From: Pyun YongHyeon <pyunyh@gmail.com> To: Alexander Shikoff <minotaur@crete.org.ua> Cc: freebsd-net@freebsd.org Subject: Re: re0: RealTek 8168/8111B: no carrier Message-ID: <20071107101407.GF70832@cdnetworks.co.kr> In-Reply-To: <20071107083204.GA33900@crete.org.ua> References: <20071106141913.GA93023@crete.org.ua> <20071106143819.GA22249@crete.org.ua> <20071107002430.GA70832@cdnetworks.co.kr> <20071107073708.GA32211@crete.org.ua> <20071107075134.GD70832@cdnetworks.co.kr> <20071107083204.GA33900@crete.org.ua>
next in thread | previous in thread | raw e-mail | index | archive | help
On Wed, Nov 07, 2007 at 10:32:04AM +0200, Alexander Shikoff wrote: > On Wed, Nov 07, 2007 at 04:51:34PM +0900, Pyun YongHyeon wrote: > > On Wed, Nov 07, 2007 at 09:37:08AM +0200, Alexander Shikoff wrote: > > > On Wed, Nov 07, 2007 at 09:24:30AM +0900, Pyun YongHyeon wrote: > > > > > > # pciconf -lv > > > > > > [...] > > > > > > re0@pci0:3:0:0: class=0x020000 card=0xe0001458 chip=0x816810ec rev=0x01 hdr=0x00 > > > > > > vendor = 'Realtek Semiconductor' > > > > > > device = 'RTL8168/8111 PCI-E Gigabit Ethernet NIC' > > > > > > class = network > > > > > > subclass = ethernet > > > > > > [...] > > > > > > > > > > Further investigation... It seems that re(4) driver does not > > > > > support auto-negotiation correctly. If I manually set media to 100baseTX and > > > > > bring up interface with 'ifconfig re0 up' then it works. > > > > > > > > > > > > > Would you show me more information for link partner(i.e. FreeBSD 6.2 box)? > > > > > > Yes, of course: > > > > > > FreeBSD 6.2-STABLE 7.0-BETA2 > > > rl0 <===================> re0 > > > > > > rl0: <RealTek 8139 10/100BaseTX> port 0x9000-0x90ff mem 0xfa000000-0xfa0000ff irq 21 at device 1.0 on pci2 > > > miibus0: <MII bus> on rl0 > > > rl0: Ethernet address: 00:e0:7d:db:ca:98 > > > rl0: link state changed to UP > > > > > > # pciconf -lv > > > rl0@pci2:1:0: class=0x020000 card=0x813910ec chip=0x813910ec rev=0x10 hdr=0x00 > > > vendor = 'Realtek Semiconductor' > > > device = 'RT8139 (A/B/C/810x/813x/C+) Fast Ethernet Adapter' > > > class = network > > > subclass = ethernet > > > > > > > Hmm, the link partner uses rl(4) so show me the PHY driver(rlphy(4)?) > > information. (You can extract it from dmesg(8) output.) > rlphy0: <RealTek internal media interface> on miibus0 > rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > > > Does the link partner has a forced speed/duplex option for rl(4)? > No. > # ifconfig rl0 > rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > options=8<VLAN_MTU> > inet 10.0.34.1 netmask 0xffffff00 broadcast 10.0.34.255 > ether 00:e0:7d:db:ca:98 > media: Ethernet autoselect (100baseTX <full-duplex>) > status: active > I couldn't see guilty code. In fact I couldn't reproduce it here. Since RTL8168/8111 has built-in crossover detection feature how about using straight cable? -- Regards, Pyun YongHyeon
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20071107101407.GF70832>