Date: Thu, 30 Oct 1997 21:11:33 +0000 (GMT) From: sporkl <spork@dti.net> To: freebsd questions <freebsd-questions@freebsd.org> Subject: X (fwd) Message-ID: <Pine.BSF.3.96.971030211033.754A-100000@iconoclast.com>
next in thread | raw e-mail | index | archive | help
Hello. I am sorry I didn't do this earlier, but I didn't reboot after the first two or so minutes of leaving my monitor off and X on. after about 6-7 minutes, it didn't beep at my Ctrl-Alt-Backspace, so i turned my monitor on and I was back in text mode. startx.log was full! Here is my startx log: XFree86 Version 3.2 / X Window System (protocol Version 11, revision 0, vendor release 6100) Release Date: Oct 26 1996 If the server is older than 6-12 months, or if your card is newer than the above date, look for a newer version before reporting problems. (see http://www.XFree86.Org/FAQ) Operating System: FreeBSD 2.2.0 Configured drivers: SVGA: server for SVGA graphics adaptors (Patchlevel 0): NV1, STG2000, et4000, et4000w32, et4000w32i, et4000w32p, et4000w32p, et6000, et3000, pvga1, wd90c00, wd90c10, wd90c30, wd90c24, wd90c31, wd90c33, gvga, ati, sis86c201, sis86c202, sis86c205, tvga8200lx, tvga8800cs, tvga8900b, tvga8900c, tvga8900cl, tvga8900d, tvga9000, tvga9000i, tvga9100b, tvga9200cxr, tgui9320lcd, tgui9400cxi, tgui9420, tgui9420dgi, tgui9430dgi, tgui9440agi, tgui9660xgi, tgui9680, cyber938x, clgd5420, clgd5422, clgd5424, clgd5426, clgd5428, clgd5429, clgd5430, clgd5434, clgd5436, clgd5446, clgd5462, clgd5464, clgd6205, clgd6215, clgd6225, clgd6235, clgd7541, clgd7542, clgd7543, clgd7548, ncr77c22, ncr77c22e, mga2064w, oti067, oti077, oti087, oti037c, al2101, ali2228, ali2301, ali2302, ali2308, ali2401, cl6410, cl6412, cl6420, cl6440, video7, ct65520, ct65530, ct65540, ct65545, ct65546, ct65548, ct65550, ct65554, ark1000vl, ark1000pv, ark2000pv, ark2000mt, mx, realtek, AP6422, generic Using syscons driver with X support (version 2.0) (using VT number 12) XF86Config: /usr/X11R6/lib/X11/XF86Config (**) stands for supplied, (--) stands for probed/default values (**) XKB: disabled (**) XKB: keymap: "xfree86(us)" (overrides other XKB settings) (**) Mouse: type: MouseSystems, device: /dev/ttyd0, baudrate: 1200 (**) SVGA: Graphics device ID: "ET4000/W32, W32i, W32p (generic)" (**) SVGA: Monitor ID: "My Monitor" (--) SVGA: Mode "640x480" needs hsync freq of 36.46 kHz. Deleted. (--) SVGA: Mode "800x600" needs hsync freq of 37.88 kHz. Deleted. (--) SVGA: Mode "800x600" needs hsync freq of 48.08 kHz. Deleted. (--) SVGA: Mode "1024x768" needs hsync freq of 48.36 kHz. Deleted. (--) SVGA: Mode "1024x768" needs hsync freq of 56.48 kHz. Deleted. (--) SVGA: Mode "1280x1024" needs hsync freq of 51.02 kHz. Deleted. (--) SVGA: Mode "1024x768" needs hsync freq of 62.50 kHz. Deleted. (--) SVGA: Mode "1280x1024" needs hsync freq of 64.25 kHz. Deleted. (--) SVGA: Mode "1280x1024" needs hsync freq of 78.86 kHz. Deleted. (--) SVGA: Mode "1280x1024" needs hsync freq of 81.13 kHz. Deleted. (--) SVGA: Mode "320x240" needs hsync freq of 39.38 kHz. Deleted. (--) SVGA: Mode "400x300" needs hsync freq of 37.88 kHz. Deleted. (--) SVGA: Mode "400x300" needs hsync freq of 48.08 kHz. Deleted. (--) SVGA: Mode "480x300" needs hsync freq of 37.80 kHz. Deleted. (--) SVGA: Mode "480x300" needs hsync freq of 39.56 kHz. Deleted. (--) SVGA: Mode "480x300" needs hsync freq of 48.00 kHz. Deleted. (**) FontPath set to "/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/75dpi/:unscaled,/usr/X11R6/lib/X11/fonts/75dpi/" (--) SVGA: ET4000: Initial hibit state: high (--) SVGA: chipset: et4000w32 (--) SVGA: videoram: 1024k (--) SVGA: clocks: 25.04 28.32 32.47 35.99 40.01 44.84 31.48 37.49 (--) SVGA: clocks: 50.09 56.65 64.95 72.00 80.02 89.70 62.97 75.00 (--) SVGA: clocks: 41.50 46.68 50.09 52.00 54.03 59.97 64.88 67.27 (--) SVGA: clocks: 83.01 93.38 100.20 104.01 108.07 119.97 129.79 134.56 (--) SVGA: Maximum allowed dot-clock: 90.000 MHz (**) SVGA: Mode "640x480": mode clock = 25.175, clock used = 25.040 (**) SVGA: Mode "800x600": mode clock = 36.000, clock used = 35.990 (**) SVGA: Mode "1024x768": mode clock = 44.900, clock used = 44.840 (--) SVGA: There is no mode definition named "1280x1024" (--) SVGA: Removing mode "1280x1024" from list of valid modes. (--) SVGA: Virtual resolution set to 1024x768 (--) SVGA: Generic SpeedUps selected (Flags=0x30) (--) SVGA: ET4000: SpeedUps selected (Flags=0xf) PEX extension module not loaded XIE extension module not loaded X connection to :0.0 broken (explicit kill or server shutdown). X connection to :0.0 broken (explicit kill or server shutdown). login: fatal IO error 32 (Broken pipe) or KillClient on X server ":0.0" xterm: fatal IO error 32 (Broken pipe) or KillClient on X server ":0.0" xinit: connection to X server lost. waiting for X server to shut down xterm: fatal IO error 32 (Broken pipe) or KillClient on X server ":0.0" Ok, so this tells me that my Hsync is too low (I think) Should I up my Hsync to accomodate those graphical modes, up to my monitors resolution limit (1024x768)? Thank you for your patience, I should have waited longer previously. :( Sorry if you get this twice, my mind was in Emacs mode so I hit the wrong key stroke and I botched the mailing of this message. -Spike Gronim sporkl@dti.net "Tradition is the chastity belt of the mind"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.3.96.971030211033.754A-100000>