Skip site navigation (1)Skip section navigation (2)
Date:      Sat, 28 Sep 2002 19:35:13 +0200
From:      "Niels Chr. Bank-Pedersen" <ncbp@bank-pedersen.dk>
To:        Mark Murray <mark@grondar.za>
Cc:        sos@freebsd.org, current@freebsd.org
Subject:   Re: ATA driver broken?
Message-ID:  <20020928173512.GF11679@bank-pedersen.dk>
In-Reply-To: <200209281655.g8SGt2cD000650@grimreaper.grondar.org>
References:  <200209281655.g8SGt2cD000650@grimreaper.grondar.org>

next in thread | previous in thread | raw e-mail | index | archive | help

--sdtB3X0nJg68CQEu
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline

On Sat, Sep 28, 2002 at 05:55:02PM +0100, Mark Murray wrote:
> Hi
> 
> I can't boot a kernel after my 22nd Sept one. The ATA disk controller
> does not probe at all, and no bootable disk is found by the kernel.
> 
> The machine is a Toshiba Libretto 110CT.

I'm seeing the same (sortof) on my Dual PIII machine - ATA as well as
ISA (PCI-ISA bridge), SCSI (sym) and NIC (fxp) has dissapeared recently.
I was suspecting the legacy(4) commits on the 23rd to be causing this.
Boot messages (before/after) attached.

[...]


/Niels Chr.

-- 
 Niels Christian Bank-Pedersen, NCB1-RIPE.

 "Hey, are any of you guys out there actually *using* RFC 2549?"

--sdtB3X0nJg68CQEu
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename=dmsg2

Console: serial port
BIOS drive A: is disk0
BIOS drive C: is disk1
BIOS drive D: is disk2
BIOS drive E: is disk3
BIOS drive F: is disk4
BIOS drive G: is disk5
BIOS 635kB/1047488kB available memory

FreeBSD/i386 bootstrap loader, Revision 1.1
(root@monster.bank-pedersen.dk, Fri Sep 27 19:22:18 CEST 2002)
Loading /boot/defaults/loader.conf 
/boot/kernel/kernel text=0x23a018 data=0x310d4+0x3f9cc syms=[0x4+0x2f600+0x4+0x390ba]

Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel] in 9 seconds... 

Type '?' for a list of commands, 'help' for more detailed help.
OK unload
OK boot kernel.old
/boot/kernel.old/kernel text=0x236c40 data=0x30df4+0x3f76c syms=[0x4+0x2eb40+0x4+0x38a17]
/boot/kernel.old/acpi.ko text=0x37254 data=0x1a84+0x6e0 syms=[0x4+0x5540+0x4+0x702d]
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #0: Mon Sep 16 22:10:00 CEST 2002
    root@monster.bank-pedersen.dk:/data/usr/obj/raid01/usr/src/sys/MONSTER
Preloaded elf kernel "/boot/kernel.old/kernel" at 0xc0458000.
Preloaded elf module "/boot/kernel.old/acpi.ko" at 0xc04580ac.
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (448.88-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x673  Stepping = 3
  Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 1073676288 (1048512K bytes)
avail memory = 1037463552 (1013148K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): apic id:  1, version: 0x00040011, at 0xfee00000
 cpu1 (AP):  apic id:  0, version: 0x00040011, at 0xfee00000
 io0 (APIC): apic id:  2, version: 0x00170011, at 0xfec00000
Pentium Pro MTRR support enabled
Using $PIR table, 8 entries at 0xc00fdf40
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <PTLTD    RSDT  > on motherboard
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-safe"  frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xc08-0xc0b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_cpu1: <CPU> on acpi0
acpi_button0: <Sleep Button> on acpi0
pcib1: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib1
IOAPIC #0 intpin 21 -> irq 2
IOAPIC #0 intpin 22 -> irq 9
IOAPIC #0 intpin 20 -> irq 10
sym0: <875> port 0x1400-0x14ff mem 0xfa100000-0xfa100fff,0xfa103000-0xfa1030ff irq 2 at device 13.0 on pci0
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym1: <875> port 0x1800-0x18ff mem 0xfa101000-0xfa101fff,0xfa103400-0xfa1034ff irq 9 at device 13.1 on pci0
sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x1060-0x107f mem 0xfa000000-0xfa0fffff,0xfa104000-0xfa104fff irq 10 at device 15.0 on pci0
fxp0: Ethernet address 00:90:27:73:c2:02
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI-ISA bridge> at device 18.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0x1050-0x105f at device 18.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <serial bus, USB> at device 18.2 (no driver attached)
Timecounter "PIIX"  frequency 3579545 Hz
pci0: <bridge, PCI-unknown> at device 18.3 (no driver attached)
pci0: <display, VGA> at device 20.0 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0 port 0x378-0x37f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A, console
orm0: <Option ROMs> at iomem 0xe4000-0xe7fff,0xcc000-0xcc7ff,0xc8000-0xcbfff,0xc0000-0xc7fff on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
Timecounters tick every 10.000 msec
ad0: DMA limited to UDMA33, non-ATA66 cable or device
ad0: 76345MB <MAXTOR 6L080L4> [155114/16/63] at ata0-master UDMA33
Waiting 5 seconds for SCSI devices to settle
da0 at sym0 bus 0 target 0 lun 0
da0: <QUANTUM ATLAS IV 18 WLS 0808> Fixed Direct Access SCSI-3 device 
da0: 40.000MB/s transfers (20.000MHz, offset 16, 16bit), Tagged Queueing Enabled
da0: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C)
da1 at sym0 bus 0 target 1 lun 0
da1: <QUANTUM ATLAS IV 18 WLS 0808> Fixed Direct Access SCSI-3 device 
da1: 40.000MB/s transfers (20.000MHz, offset 16, 16bit), Tagged Queueing Enabled
da1: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C)
da2 at sym0 bus 0 target 2 lun 0
da2: <QUANTUM ATLAS IV 18 WLS 0808> Fixed Direct Access SCSI-3 device 
da2: 40.000MB/s transfers (20.000MHz, offset 16, 16bit), Tagged Queueing Enabled
da2: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C)
da3 at sym0 bus 0 target 3 lun 0
da3: <QUANTUM ATLAS IV 18 WLS 0808> Fixed Direct Access SCSI-3 device 
da3: 40.000MB/s transfers (20.000MHz, offset 16, 16bit), Tagged Queueing Enabled
da3: 17522MB (35885168 512 byte sectors: 255H 63S/T 2233C)
SMP: AP CPU #1 Launched!
Mounting root from ufs:/dev/da0s1a
Entropy harvesting: interrupts ethernet point_to_point.


--sdtB3X0nJg68CQEu
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename=dmsg1

Console: serial port
BIOS drive A: is disk0
BIOS drive C: is disk1
BIOS drive D: is disk2
BIOS drive E: is disk3
BIOS drive F: is disk4
BIOS drive G: is disk5
BIOS 635kB/1047488kB available memory

FreeBSD/i386 bootstrap loader, Revision 1.1
(root@monster.bank-pedersen.dk, Fri Sep 27 19:22:18 CEST 2002)
Loading /boot/defaults/loader.conf 
/boot/kernel/kernel text=0x23a018 data=0x310d4+0x3f9cc syms=[0x4+0x2f600+0x4+0x390ba]

Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...               
/boot/kernel/acpi.ko text=0x37174 data=0x1a84+0x6e0 syms=[0x4+0x5540+0x4+0x702]/
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #0: Fri Sep 27 17:56:09 CEST 2002
    root@monster.bank-pedersen.dk:/data/usr/obj/raid01/usr/src/sys/MONSTER
Preloaded elf kernel "/boot/kernel/kernel" at 0xc045d000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc045d0a8.
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (448.88-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x673  Stepping = 3
  Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 1073676288 (1048512K bytes)
avail memory = 1037709312 (1013388K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): apic id:  1, version: 0x00040011, at 0xfee00000
 cpu1 (AP):  apic id:  0, version: 0x00040011, at 0xfee00000
 io0 (APIC): apic id:  2, version: 0x00170011, at 0xfec00000
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <PTLTD    RSDT  > on motherboard
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-safe"  frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xc08-0xc0b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_cpu1: <CPU> on acpi0
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0 port 0x378-0x37f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A, console
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
Timecounters tick every 10.000 msec
SMP: AP CPU #1 Launched!
Mounting root from ufs:/dev/da0s1a
setrootbyname failed
ffs_mountroot: can't find rootvp
Root mount failed: 6

Manual root filesystem specification:
  <fstype>:<device>  Mount <device> using filesystem <fstype>
                       eg. ufs:da0s1a
  ?                  List valid disk boot devices
  <empty line>       Abort manual input

mountroot> ufs:da0s1a
Mounting root from ufs:da0s1a
setrootbyname failed
ffs_mountroot: can't find rootvp
Root mount failed: 6


--sdtB3X0nJg68CQEu--

To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020928173512.GF11679>