Date: Sat, 03 Jun 2000 21:46:54 +0200 From: sthaug@nethelp.no To: mlistbsd@icorp.net Cc: freebsd-isp@freebsd.org, freebsd-questions@freebsd.org Subject: Re: Compaq Proliant 3000 & RAID Message-ID: <68919.960061614@verdi.nethelp.no> In-Reply-To: Your message of "Sat, 03 Jun 2000 14:37:05 -0500" References: <39395E61.909E59DC@icorp.net>
next in thread | previous in thread | raw e-mail | index | archive | help
> I just purchased a Compaq Proliant 3000 and want to set up a RAID system
> for it. Has anyone run FreeBSD on this hardware - any comments?
Running 3.4-STABLE with the sym driver here, on a dual processor Proliant
3000 system. It's working very well. I have no experience with RAID on this
hardware, though.
If you use the builtin SCSI controllers: Please use the sym driver, not
the ncr driver. The difference in stability is significant (currently 104
days uptime with the sym driver - we used to have a crash about once per
week or so with the ncr driver).
Steinar Haug, Nethelp consulting, sthaug@nethelp.no
----------------------------------------------------------------------
Copyright (c) 1992-1999 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 3.4-20000124-STABLE #0: Sat Feb 19 23:14:12 CET 2000
sthaug@newsfeed1.telia.no:/local/freebsd/src/sys/compile/NEWSFEED1_SYM
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Xeon/Celeron (686-class CPU)
Origin = "GenuineIntel" Id = 0x651 Stepping = 1
Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 603979776 (589824K bytes)
avail memory = 584105984 (570416K bytes)
Programming 28 pins in IOAPIC #0
EISA INTCONTROL = 00000620
IOAPIC #0 intpint 24 -> irq 5
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 8, version: 0x001b0011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc02d6000.
Pentium Pro MTRR support enabled
eisa0: <CPQ561 (System Board)>
Probing for devices on the EISA bus
Probing for devices on PCI bus 0:
chip0: <Ross (?) host to PCI bridge> rev 0x03 on pci0.0.0
vga0: <Cirrus Logic GD5430 SVGA controller> rev 0x22 int a irq 255 on pci0.6.0
chip1: <PCI to EISA bridge (vendor=0e11 device=0001)> rev 0x07 on pci0.15.0
chip2: <Ross (?) host to PCI bridge> rev 0x03 on pci0.17.0
Probing for devices on PCI bus 1:
sym0: <875> rev 0x14 int a irq 19 on pci1.4.0
sym0: No NVRAM, ID 7, Fast-20, parity checking
sym1: <875> rev 0x14 int b irq 18 on pci1.4.1
sym1: No NVRAM, ID 7, Fast-20, parity checking
fxp0: <Intel EtherExpress Pro 10/100B Ethernet> rev 0x05 int a irq 18 on pci1.7.0
fxp0: Ethernet address 00:90:27:13:f6:21
tl0: <Compaq Netelligent 10/100> rev 0x10 int a irq 17 on pci1.8.0
tl0: Ethernet address: 00:08:c7:1e:a7:35
tl0: autoneg complete, link status good (full-duplex, 100Mbps)
Probing for devices on PCI bus 2:
Probing for devices on the ISA bus:
sc0 on isa
sc0: VGA color <16 virtual consoles, flags=0x0>
atkbdc0 at 0x60-0x6f on motherboard
atkbd0 irq 1 on isa
psm0: failed to get data.
psm0 irq 12 on isa
psm0: model IntelliMouse, device ID 3
sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: FIFO enabled, 8 bytes threshold
fd0: 1.44MB 3.5in
wdc0 at 0x1f0-0x1f7 irq 14 on isa
wdc0: unit 0 (atapi): <CD-ROM CDU571-Q/1.1a>, removable, accel, dma, iordis
acd0: drive speed 1378KB/sec, 128KB cache
acd0: supported read types: CD-DA
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
npx0 on motherboard
npx0: INT 16 interface
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: Broken MP table detected: 8254 is not connected to IO APIC int pin 2
APIC_IO: routing 8254 via 8259 on pin 0
ccd0-3: Concatenated disk drivers
Waiting 5 seconds for SCSI devices to settle
SMP: AP CPU #1 Launched!
changida0 at sym0 bus 0 target 0 lun 0
da0: <COMPAQ HD0093172C 3207> Fixed Direct Access SCSI-2 device
da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da0: 8678MB (17773500 512 byte sectors: 255H 63S/T 1106C)
da2 at sym0 bus 0 target 4 lun 0
da2: <COMPAQ HD0093172C 3207> Fixed Direct Access SCSI-2 device
da2: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da2: 8678MB (17773500 512 byte sectors: 255H 63S/T 1106C)
da3 at sym0 bus 0 target 5 lun 0
da3: <COMPAQ HD0093172C 3207> Fixed Direct Access SCSI-2 device
da3: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da3: 8678MB (17773500 512 byte sectors: 255H 63S/T 1106C)
da1 at sym0 bus 0 target 1 lun 0
da1: <COMPAQ HD0093172C 3207> Fixed Direct Access SCSI-2 device
da1: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da1: 8678MB (17773500 512 byte sectors: 255H 63S/T 1106C)
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-isp" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?68919.960061614>