Date: Mon, 12 Apr 2010 07:29:33 -0700 From: Garrett Cooper <yanefbsd@gmail.com> To: multimedia@freebsd.org Subject: Re: Buzzing snd_emu10kx enabled card with r206173 Message-ID: <q2l7d6fde3d1004120729h2d32e696g4182af399580ca01@mail.gmail.com> In-Reply-To: <p2v7d6fde3d1004060339nfdbc4cb9p9ac6e232e38b4d6@mail.gmail.com> References: <u2q7d6fde3d1004051122madc6ebb4jc3248d8c68a81333@mail.gmail.com> <x2m7d6fde3d1004051226k7a0e350bz579b899e4fedd977@mail.gmail.com> <p2v7d6fde3d1004060339nfdbc4cb9p9ac6e232e38b4d6@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Tue, Apr 6, 2010 at 3:39 AM, Garrett Cooper <yanefbsd@gmail.com> wrote:
> On Mon, Apr 5, 2010 at 12:26 PM, Garrett Cooper <yanefbsd@gmail.com> wrot=
e:
>> On Mon, Apr 5, 2010 at 11:22 AM, Garrett Cooper <yanefbsd@gmail.com> wro=
te:
>>> Hi,
>>> =A0 =A0When I first installed FreeBSD on this machine, I had a heck of =
a
>>> time getting the soundcard's PCM channel to function properly. It
>>> would buzz incessantly when I played any audio on it; I disabled the
>>> onboard snd_hda enabled audio and things magically worked, until
>>> today. After a kernel upgrade and a few warm boots, I'm back to where
>>> I started from -- the PCM channel buzzes whenever I play audio;
>>> line-in works perfectly fine however. I'm not seeing anything out of
>>> the ordinary in commits over the past couple of weeks for the pcm
>>> pieces (the last successful kernel I used was 2~3 weeks old).
>>> =A0 =A0Are there any device_printf's I should add or a debug procedure
>>> that you recommend I do to triage the situation?
>>> Thanks,
>>> -Garrett
>>>
>>> # uname -a
>>> FreeBSD bayonetta.local 9.0-CURRENT FreeBSD 9.0-CURRENT #1 r206173M:
>>> Sun Apr =A04 19:54:22 PDT 2010
>>> root@bayonetta.local:/usr/obj/usr/src/sys/BAYONETTA =A0amd64
>>> # pciconf -lv | grep -A 4 emu
>>> emu10kx0@pci0:8:0:0: =A0 =A0class=3D0x040100 card=3D0x10211102 chip=3D0=
x00081102
>>> rev=3D0x00 hdr=3D0x00
>>> =A0 =A0vendor =A0 =A0 =3D 'Creative Technology LTD.'
>>> =A0 =A0device =A0 =A0 =3D 'sound blaster Audigy 2 (ca0108)'
>>> =A0 =A0class =A0 =A0 =A0=3D multimedia
>>> =A0 =A0subclass =A0 =3D audio
>>> # dmesg | grep 'irq 16'
>>> uhci0: <Intel 82801JI (ICH10) USB controller USB-D> port 0xa800-0xa81f
>>> irq 16 at device 26.0 on pci0
>>> pcib7: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0
>>> emu10kx0: <Creative Audigy 4 [SB0610]> port 0xec00-0xec3f irq 16 at
>>> device 0.0 on pci8
>>> # dmesg | grep 'pcm'
>>> pcm0: <EMU10Kx DSP front PCM interface> on emu10kx0
>>> pcm0: <SigmaTel STAC9750/51 AC97 Codec>
>>> pcm1: <EMU10Kx DSP rear PCM interface> on emu10kx0
>>> pcm2: <EMU10Kx DSP center PCM interface> on emu10kx0
>>> pcm3: <EMU10Kx DSP subwoofer PCM interface> on emu10kx0
>>> pcm4: <EMU10Kx DSP side PCM interface> on emu10kx0
>>
>> Some more information:
>>
>> 1. snd_emu10kx and sound are both modules loaded on boot, along with
>> if_re, linux, and nvidia.
>> 2. Disabling nvidia -> no change.
>> 3. Disabling acpi -> unbootable system because many drivers can't map
>> interrupts without it (can't test unless I isolate the drivers and
>> enable them one by one -- something I'll try later on).
>>
>> I'm at a loss right now... my hunch is that it's potentially a bad
>> interaction between the snd_emu10kx driver and another driver on the
>> same PCI bus (which is just the ACPI and uhci drivers), but I can't
>> test these claims. There are other funky things about my system that
>> have changed over the past couple of kernel versions, like front USB
>> ports could charge my iPhone, and now they don't... and the fact that
>> ACPI blanking via nvidia now works again... so something may have
>> changed on the backend, but I'm not 100% sure on what I should isolate
>> as the root cause, yet.
>
> Grr... it's `healed' itself again. I'll watch out for potential
> catalysts to the issue in the future.
Ok. Damn issue came back and here's what happened. Rebooted
several times with the same kernel and slight modifications, loading
and unloading snd_emu10kx and sound, testing out snd_emu10k1, and no
dice. The buzz was bad and it was driving me insane. Again, line-in
functioned just fine, so I didn't know what the heck was going. I was
getting desperate, so I finally broke down and booted the Gentoo Linux
livecd. PCM worked just fine. Then I got irritated enough and finally
just built the module and the sound support directly into the kernel
and everything is hunky dorey again. Does anyone have a stab in the
dark as to what's going on? Is it a potential bus or interrupt
conflict / race condition that gets alleviated when support is nailed
into the kernel? Or are other folks as stumped as I am, s.t. I should
just try emailing current@ instead to see if someone maybe knows
what's going on there :(...?
Thanks,
-Garrett
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?q2l7d6fde3d1004120729h2d32e696g4182af399580ca01>