Date: Sun, 24 Sep 2006 15:59:03 -0500 From: Bruce Burden <brucegb@realtime.net> To: freebsd-current@freebsd.org Subject: Re: LSI 1030 mpt doesn't work if I build a new kernel Message-ID: <20060924205903.GY1045@tigerfish2.my.domain> In-Reply-To: <20060924071601.GA1080@les.ath.cx> References: <1157154024.835.6.camel@atomizer.opensourcebeef.net> <20060924071601.GA1080@les.ath.cx>
next in thread | previous in thread | raw e-mail | index | archive | help
On Sun, Sep 24, 2006 at 04:16:01PM +0900, YONETANI Tomokazu wrote:
>
> Recently I tried installing FreeBSD 5.4-RELEASE on an IBM X335 in my
> office and tried to upgrade to 6.2-PRERELEASE, and found that although
> it doesn't hang or panic during boot, running I/O intensive applications
> (including buildworld) ends up in an I/O error, and eventually panicked and
> rebooted.
>
This would be best on -STABLE, which the 6x thread is. Anyway,
I have:
[root@tigerfish2 ~]# camcontrol devlist -v
scbus0 on sbp0 bus 0:
< > at scbus0 target -1 lun -1 ()
scbus1 on mpt0 bus 0:
<SEAGATE DAT 06240-XXX 8040> at scbus1 target 0 lun 0 (sa0,pass0)
<PLEXTOR CD-ROM PX-40TW 1.04> at scbus1 target 4 lun 0 (pass1,cd0)
<IBM DDYS-T18350N S96H> at scbus1 target 5 lun 0 (da0,pass2)
< > at scbus1 target -1 lun -1 ()
scbus2 on mpt1 bus 0:
<SEAGATE ST336607LW 0007> at scbus2 target 6 lun 0 (da1,pass3)
< > at scbus2 target -1 lun -1 ()
scbus3 on asr0 bus 0:
<ADAPTEC RAID-5 370F> at scbus3 target 1 lun 0 (da2,pass4)
<ADAPTEC REDIRECT DRIVE 370F> at scbus3 target 5 lun 0 (da3,pass5)
<SUPER GEM318 0> at scbus3 target 6 lun 0 (ses0,pass6)
< > at scbus3 target -1 lun -1 ()
scbus4 on asr0 bus 1:
< > at scbus4 target -1 lun -1 ()
scbus5 on ata0 bus 0:
<SONY DVD RW DRU-800A KY01> at scbus5 target 0 lun 0 (pass7,cd1)
< > at scbus5 target -1 lun -1 ()
scbus6 on ata1 bus 0:
< > at scbus6 target -1 lun -1 ()
scbus-1 on xpt0 bus 0:
< >
mpt0@pci10:6:0: class=0x010000 card=0x289510f1 chip=0x00301000 rev=0x07 hdr=0x00
vendor = 'LSI Logic (Was: Symbios Logic, NCR)'
device = 'LSI53C1020/1030 PCI-X to Ultra320 SCSI Controller'
class = mass storage
subclass = SCSI
mpt1@pci10:6:1: class=0x010000 card=0x289510f1 chip=0x00301000 rev=0x07 hdr=0x00
vendor = 'LSI Logic (Was: Symbios Logic, NCR)'
device = 'LSI53C1020/1030 PCI-X to Ultra320 SCSI Controller'
class = mass storage
subclass = SCSI
FreeBSD tigerfish2.my.domain 6.1-STABLE FreeBSD 6.1-STABLE #6: Sun Aug 27 11:03:43 CDT 2006
and have not had any problems with the mpt device. The controller is
built into the Tyan S2895/Thunder K8WE board.
I am not using the Seagate drive - it will be used to hold the
AMD64 installation when I get around to doing that, while the IBM
drive will continue to hold the i386 install if I need to switch
back. The RAID holds user data, and is not an issue when performing
kernel builds.
Have you tried to install the 6.1 release from CD/DVD?
Bruce
--
------------------------------------------------------------------------
"I like bad!" Bruce Burden Austin, TX.
- Thuganlitha
The Power and the Prophet
Robert Don Hughes
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20060924205903.GY1045>