Date: Thu, 26 Sep 2002 00:09:16 -1000 (HST) From: Vincent Poy <vince@oahu.WURLDLINK.NET> To: "M. Warner Losh" <imp@bsdimp.com> Cc: FreeBSD-mobile@FreeBSD.ORG Subject: Re: Intel Mobile fxp Cardbus cards supported? Message-ID: <20020926000019.A45901-100000@oahu.WURLDLINK.NET> In-Reply-To: <20020920.175856.112625798.imp@bsdimp.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Fri, 20 Sep 2002, M. Warner Losh wrote:
> In message: <20020920132717.O3782-100000@oahu.WURLDLINK.NET>
> Vincent Poy <vince@oahu.WURLDLINK.NET> writes:
> : Which model of the cardbus card are you using? I'm going to try
> : the MBLA3300C3 next which is the one without the modem.
>
> MBLA3300 is the one that I've used.
>
> fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x1000-0x103f mem 0xf4020000-0xf403ffff,0xf4040000-0xf4040fff irq 10 at device 0.0 on cardbus0
> fxp0: Disabling dynamic standby mode in EEPROM
> fxp0: New EEPROM ID: 0x4880
> fxp0: EEPROM checksum @ 0xff: 0x7a17 -> 0x7a19
> fxp0: Ethernet address 00:d0:b7:02:0e:f6
> inphy0: <i82555 10/100 media interface> on miibus0
> inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
>
> is what dmesg says when I insert the card. I've not used it in a
> little while, but the new EEPROM ID is something I should look into.
After trying the MBLA3300, MBLA3300C3, MBLA3356C3 on both the IBM
ThinkPad 770Z and the Dell Inspiron 8200, all three cards had the
following results:
cardbus0: Expecting link target, got 0xff
cardbus0: Resource not specified in CIS: id=10, size=1000
cardbus0: Resource not specified in CIS: id=14, size=40
cardbus0: Resource not specified in CIS: id=18, size=20000
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x1000-0x103f mem 0x88000000-0x8801ffff,0x88020000-0x88020fff irq 11 at device 0.0 on cardbus0
fxp0: Disabling dynamic standby mode in EEPROM
fxp0: New EEPROM ID: 0xfffd
fxp0: EEPROM checksum @ 0xff: 0xffff -> 0xbbb9
fxp0: Ethernet address ff:ff:ff:ff:ff:ff, 10Mbps
It seems like the autonegotition for 10/100 HDX/FDX is failing as
the dc0 and xl0 with the same cable sees 100FDX correctly.
ifconfig fxp0 output:
fxp0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether ff:ff:ff:ff:ff:ff
media: Ethernet manual
As soon as I issue the following to configure the interface:
ifconfig fxp0 inet 209.204.138.100 netmask 255.255.255.0
I get the following repeatedly non-stop:
fxp0: SCB timeout: 0xff 0xff 0xff 0xffff
fxp0: DMA timeout
fxp0: SCB timeout: 0xff 0xff 0xff 0xffff
fxp0: DMA timeout
fxp0: SCB timeout: 0xff 0xff 0xff 0xffff
fxp0: DMA timeout
fxp0: SCB timeout: 0xff 0xff 0xff 0xffff
fxp0: DMA timeout
fxp0: SCB timeout: 0xff 0xff 0xff 0xffff
Cheers,
Vince - vince@WURLDLINK.NET - Vice President ________ __ ____
Unix Networking Operations - FreeBSD-Real Unix for Free / / / / | / |[__ ]
WurldLink Corporation / / / / | / | __] ]
San Francisco - Honolulu - Hong Kong / / / / / |/ / | __] ]
HongKong Stars/Gravis UltraSound Mailing Lists Admin /_/_/_/_/|___/|_|[____]
Almighty1@IRC - oahu.DAL.NET Hawaii's DALnet IRC Network Server Admin
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020926000019.A45901-100000>