Date: Thu, 2 Oct 2003 12:34:39 +0800 (CST) From: Tai-hwa Liang <avatar@mmlab.cse.yzu.edu.tw> To: freebsd-questions@freebsd.org Subject: USB mouse doesn't work Message-ID: <03100212325316.38163@www.mmlab.cse.yzu.edu.tw>
next in thread | raw e-mail | index | archive | help
Hi,
I'm wondering about whether there's any trick to get an USB mouse
to work on FreeBSD. I've tried one(forgot its model) a couple months
before but out of luck. Recently I got the similar symptom on another
optical USB mouse modelled "ELECOM M-MAPP1KHBK" which can be probed by
kernel/usbd, but not respond to any mouse event such like moving, button
clicking or wheel scrolling.
This test has been conducted on FreeBSD 4.6-RELEASE, 4.8-RELEASE,
4.9-RC and 5.1-RELEASE(installation disc 2); all of them probed the mouse;
however, there's no correspondence mouse event output to /dev/ums0 if I
killed the moused and did a "cat /dev/ums0" to get the event output.
I've also tried the same mouse on OpenBSD 3.3 and just gotten the
same result(probed but no output to /dev/ums0 while moving/clicking the
mouse). Apparently it's true that people said [Free|Net|Open]BSD shared
the same USB stack....
However, this mouse works flawlessly on Linux(2.4.x kernel),
MacOS X 10.2.6 and M$ Windoze 2000/XP. I've tried the mouse on 4 different
laptops: Apple PowerBoot G4(MacOS X of course...), IBM Thinkpad T40,
Sony Vaio R505 and Twinhead Slimnote VX266. If I swap the ELECOM with a
Logitech one(modelled M-BD58, an optical USB wheel mouse) then everything
works again....
A blindly try to add new entry/flag such like UQ_SPUR_BUT_UP in
sys/dev/usb/usb_quirks.c doesn't work, neither. Following is the dmesg
with hw.usb.ums.debug=9999 and hw.usb.debug=1 set.
You may aware that there's a couple of status=6 within ums_intr
such like "ums_intr: sc=0xc0a89800 status=6." That's because I killed
the moused manually and then did a "cat /dev/ums0" to see what happened
during the mouse movement. In this test, the ELECOM one were attached
first, then replaced with a Logitech one.
I would be very appreciate it if someone can enlighten me about
what's really going on some USB mouse such like this ELECOM one.
----------- dmesg ripped from Thinkpad T40 --------------
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.9-RC #5: Thu Oct 2 10:14:37 CST 2003
root@odin:/usr/src/sys/compile/rtfm_dbg
Calibrating clock(s) ... TSC clock: 1395466472 Hz, i8254 clock: 1193178 Hz
Timecounter "i8254" frequency 1193178 Hz
Timecounter "TSC" frequency 1395466472 Hz
CPU: Intel(R) Pentium(R) M processor 1400MHz (1395.47-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x695 Stepping = 5
Features=0xa7e9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,TM,PBE>
real memory = 267714560 (261440K bytes)
Physical memory chunk(s):
0x000001000 - 0x00009efff, 647168 bytes (158 pages)
0x0003f4000 - 0x00ff45fff, 263528448 bytes (64338 pages)
avail memory = 256520192 (250508K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f6b70
bios32: Entry = 0xfd780 (c00fd780) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x1f6
pnpbios: Found PnP BIOS data at 0xc00f6bf0
pnpbios: Entry = f0000:9c73 Rev = 1.0
pnpbios: Event flag at 4b4
Other BIOS signatures found:
ACPI: 000f6ba0
Preloaded elf kernel "kernel" at 0xc03cd000.
Preloaded elf module "splash_bmp.ko" at 0xc03cd09c.
Preloaded splash_image_data "/boot/chuck1.bmp" at 0xc03cd140.
Preloaded elf module "if_wi.ko" at 0xc03cd190.
VESA: information block
56 45 53 41 00 02 00 01 00 01 01 00 00 00 22 00
00 01 ff 01 00 01 19 01 00 01 2f 01 00 01 34 01
00 01 82 01 0d 01 0e 01 0f 01 20 01 92 01 93 01
94 01 95 01 96 01 a2 01 a3 01 a4 01 a5 01 a6 01
VESA: 0 mode(s) found
module_register_init: MOD_LOAD (vesa, c0264c1c, 0) error 6
Pentium Pro MTRR support enabled
splash: image@0xc03720f0, size:308278
splash_bmp: No appropriate video mode found
bmp_start(): splash_mode:-1
module_register_init: MOD_LOAD (splash_bmp, c036f7a4, 0) error 19
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000f904
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=33408086)
Using $PIR table, 15 entries at 0xc00fdea0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x3340, revid=0x03
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base d0000000, size 28
found-> vendor=0x8086, dev=0x3341, revid=0x03
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x8086, dev=0x24c2, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=4
map[20]: type 1, range 32, base 00001800, size 5
found-> vendor=0x8086, dev=0x24c4, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=b, irq=10
map[20]: type 1, range 32, base 00001820, size 5
found-> vendor=0x8086, dev=0x24c7, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=c, irq=9
map[20]: type 1, range 32, base 00001840, size 5
found-> vendor=0x8086, dev=0x24cd, revid=0x01
class=0c-03-20, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=11
map[10]: type 1, range 32, base c0000000, size 10
found-> vendor=0x8086, dev=0x2448, revid=0x81
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=8 secondarybus=2
found-> vendor=0x8086, dev=0x24cc, revid=0x01
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x24ca, revid=0x01
class=01-01-8a, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=255
map[10]: type 1, range 32, base 00000000, size 3
map[14]: type 1, range 32, base 00000000, size 2
map[18]: type 1, range 32, base 00000000, size 3
map[1c]: type 1, range 32, base 00000000, size 2
map[20]: type 1, range 32, base 00001860, size 4
found-> vendor=0x8086, dev=0x24c3, revid=0x01
class=0c-05-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=b, irq=6
map[20]: type 1, range 32, base 00001880, size 5
found-> vendor=0x8086, dev=0x24c5, revid=0x01
class=04-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=b, irq=6
map[10]: type 1, range 32, base 00001c00, size 8
map[14]: type 1, range 32, base 000018c0, size 6
map[18]: type 1, range 32, base c0000c00, size 9
map[1c]: type 1, range 32, base c0000800, size 8
found-> vendor=0x8086, dev=0x24c6, revid=0x01
class=07-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=b, irq=6
map[10]: type 1, range 32, base 00002400, size 8
map[14]: type 1, range 32, base 00002000, size 7
pci0: <PCI bus> on pcib0
agp0: <Intel 82855 host to AGP bridge> mem 0xd0000000-0xdfffffff at device 0.0 on pci0
agp0: allocating GATT for aperture of size 256M
pcib1: <PCI to PCI bridge (vendor=8086 device=3341)> at device 1.0 on pci0
found-> vendor=0x1002, dev=0x4c66, revid=0x02
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=4
map[10]: type 1, range 32, base e0000000, size 27
map[14]: type 1, range 32, base 00003000, size 8
map[18]: type 1, range 32, base c0100000, size 16
pci1: <PCI bus> on pcib1
drm0: <ATI Radeon Lf R250 Mobility 9000 M9> port 0x3000-0x30ff mem 0xc0100000-0xc010ffff,0xe0000000-0xe7ffffff irq 4 at device 0.0 on pci1
info: [drm] AGP at 0xd0000000 256MB
info: [drm] Initialized radeon 1.8.0 20020828 on minor 0
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x1800-0x181f irq 4 at device 29.0 on pci0
uhci0: LegSup = 0x0000003b
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x1820-0x183f irq 10 at device 29.1 on pci0
uhci1: LegSup = 0x00000010
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ums0: ELECOM ELECOM M.A.P.P. series, rev 1.10/1.01, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x1840-0x185f irq 9 at device 29.2 on pci0
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <USB controller> (vendor=0x8086, dev=0x24cd) at 29.7 irq 11
pcib2: <Intel 82801BAM/CAM (ICH2/3) PCI to I/O Hub bridge> at device 30.0 on pci0
found-> vendor=0x104c, dev=0xac55, revid=0x01
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=5 secondarybus=3
intpin=a, irq=4
map[10]: type 1, range 32, base b0000000, size 12
found-> vendor=0x104c, dev=0xac55, revid=0x01
class=06-07-00, hdrtype=0x02, mfdev=1
subordinatebus=8 secondarybus=6
intpin=b, irq=6
map[10]: type 1, range 32, base b1000000, size 12
found-> vendor=0x8086, dev=0x101e, revid=0x03
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=4
map[10]: type 1, range 32, base c0220000, size 17
map[14]: type 1, range 32, base c0200000, size 16
map[18]: type 1, range 32, base 00008000, size 6
found-> vendor=0x8086, dev=0x1043, revid=0x04
class=02-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
map[10]: type 1, range 32, base c0210000, size 12
pci2: <PCI bus> on pcib2
pcic0: <TI PCI-1520 PCI-CardBus Bridge> mem 0xb0000000-0xb0000fff irq 4 at device 0.0 on pci2
pcic0: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
using shared irq4.
pcic0: PCI Configuration space:
0x00: 0xac55104c 0x02100107 0x06070001 0x00824008
0x10: 0xb0000000 0x020000a0 0xb0050302 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x07600104
0x40: 0x05121014 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x0844d070 0x00000000 0x00000000 0x01d21022
0x90: 0x606402c0 0x00000000 0x00000000 0x00000000
0xa0: 0xfe120001 0x00c00000 0x00000000 0x0000000f
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pccard0: <PC Card 16-bit bus (classic)> on pcic0
pcic1: <TI PCI-1520 PCI-CardBus Bridge> mem 0xb1000000-0xb1000fff irq 6 at device 0.1 on pci2
pcic1: TI12XX PCI Config Reg: [speaker enable][pwr save][CSC serial isa irq]
pcic1: PCI Configuration space:
0x00: 0xac55104c 0x02100107 0x06070001 0x00824008
0x10: 0xb1000000 0x020000a0 0xb0080602 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x07600206
0x40: 0x05121014 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x0844d070 0x00000000 0x00000000 0x01d21022
0x90: 0x606402c0 0x00000000 0x00000000 0x00000000
0xa0: 0xfe120001 0x00c00000 0x00000000 0x0000000f
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pccard1: <PC Card 16-bit bus (classic)> on pcic1
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.16> port 0x8000-0x803f mem 0xc0200000-0xc020ffff,0xc0220000-0xc023ffff irq 4 at device 1.0 on pci2
bpf: em0 attached
em0: Speed:N/A Duplex:N/A
pci2: <unknown card> (vendor=0x8086, dev=0x1043) at 2.0 irq 9
isab0: <PCI to ISA bridge (vendor=8086 device=24cc)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4-M ATA100 controller> port 0x1860-0x186f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1860
ata0: mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ata0-master: ATA 01 a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1868
ata1: mask=03 ostat0=50 ostat2=00
ata1-master: ATAPI 14 eb
ata1-slave: ATAPI 14 eb
ata1: mask=03 stat0=00 stat1=00
ata1: devices=0c
ata1: at 0x170 irq 15 on atapci0
ichsmb0: <Intel 82801DC (ICH4) SMBus controller> port 0x1880-0x189f irq 6 at device 31.3 on pci0
using shared irq6.
smbus0: <System Management Bus> on ichsmb0
smb0: <SMBus general purpose I/O> on smbus0
pcm0: <Intel ICH4 (82801DB)> port 0x18c0-0x18ff,0x1c00-0x1cff mem 0xc0000800-0xc00008ff,0xc0000c00-0xc0000dff irq 6 at device 31.5 on pci0
pcm0: <Analog Devices AD1981B AC97 Codec (id = 0x41445374)>
pcm0: Codec features headphone, 20 bit DAC, 5 bit master volume, no 3D Stereo Enhancement
pcm0: Primary codec extended features variable rate PCM, AMAP, reserved 4
pcm0: sndbuf_setmap 47000, 4000; 0xdb3df000 -> 47000
pcm0: sndbuf_setmap 4b000, 4000; 0xdb3e3000 -> 4b000
chip0: <Intel 82801DB (ICH4) AC'97 Modem Controller> port 0x2000-0x207f,0x2400-0x24ff irq 6 at device 31.6 on pci0
pcic-: pcic0 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc0000-0xcffff,0xd0000-0xd0fff,0xd1000-0xd1fff,0xdc000-0xdffff,0xe0000-0xeffff on isa0
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x54ab (2)
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> flags 0x100 irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00006100, flags:00000000, packet size:3
psm0: syncmask:00, syncbits:00
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
vga0: vga: WARNING: video mode switching is not fully supported on this adapter
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 64 4f 4f 88 59 9e
9a 1f 00 4f 0d 0e 00 00 06 e0 92 83 8f 28 1f 8f
9b a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 67 64 4f 4f 88 59 9e
9a 1f 00 4f 0d 0e 00 00 06 e0 92 83 8f 28 1f 8f
9b a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic2 failed to probe at port 0x3e0-0x3e1 irq 11 on isa0
pcf0: <PCF8584 I2C bus controller> at port 0x320-0x321 irq 5 on isa0
iicbus0: <Philips I2C bus> on pcf0 addr 0xaa
iicbus: iic devclass not found
iicsmb0: <I2C to SMB bridge> on iicbus0
smbus1: <System Management Bus> on iicsmb0
smb1: <SMBus general purpose I/O> on smbus1
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
PC873xx probe at 0x2e got unknown ID 0x0
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03feef3f 0..1022=1023 cylinders, 0..239=240 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
ata1-slave: ATAPI identify retries exceeded
ad0: success setting UDMA5 on Intel chip
Creating DISK ad0
ar: FreeBSD check1 failed
ad0: <IC25N040ATCS05-0/CS4OA61A> ATA-5 disk at ata0-master
ad0: 35174MB (72037362 sectors), 71465 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
ad0: piomode=4 dmamode=2 udmamode=5 cblid=1
ata1-master: piomode=4 dmamode=2 udmamode=2 dmaflag=1
ata1-master: success setting UDMA2 on Intel chip
acd0: <UJDA745 DVD/CDRW/1.02> CD-RW drive at ata1 as master
acd0: read 4134KB/s (34515KB/s) write 1722KB/s (1722KB/s), 2048KB buffer, UDMA33
acd0: Reads: CD-R, CD-RW, CD-DA stream, DVD-ROM, DVD-R, DVD-RAM, packet
acd0: Writes: CD-R, CD-RW, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-RW 120mm photo disc
pcm0: measured ac97 link rate at 47992 Hz, will use 48000 Hz
Mounting root from ufs:/dev/ad0s4a
ad0s1: type 0xf, start 30875040, end = 72031679, size 41156640 : OK
ad0s2: type 0xb, start 63, end = 13744079, size 13744017 : OK
ad0s3: type 0x83, start 13744080, end = 13789439, size 45360 : OK
ad0s4: type 0xa5, start 13789440, end = 30875039, size 17085600 : OK
ad0s5: type 0x83, start 30875103, end = 36106559, size 5231457
ad0s5: C/H/S start 1023/1/1 (15467823) != start 30875103: invalid
ad0<extended>: type 0x5, start 36106560, end = 72031679, size 35925120
ad0<extended>: C/H/S start 1023/0/1 (15467760) != start 36106560: invalid
ad0s6: type 0xb, start 36106623, end = 72031679, size 35925057
ad0s6: C/H/S start 1023/1/1 (15467823) != start 36106623: invalid
start_init: trying /sbin/init
em0: Link is up 100 Mbps Full Duplex
splash: image decoder found: blank_saver
Linux ELF exec handler installed
info: [drm] Loading R200 Microcode
ums_intr: sc=0xc0a89800 status=13
ums_intr: data = e0 cc c9
ums_intr: status=13
ums_intr: sc=0xc0a89800 status=13
ums_intr: data = e0 cc c9
ums_intr: status=13
ums_intr: sc=0xc0a89800 status=13
ums_intr: data = e0 cc c9
ums_intr: status=13
ums_intr: sc=0xc0a89800 status=13
ums_intr: data = e0 cc c9
ums_intr: status=13
ums_intr: sc=0xc0a89800 status=13
ums_intr: data = e0 cc c9
ums_intr: status=13
ums0: at uhub1 port 2 (addr 2) disconnected
ums_intr: sc=0xc0a89800 status=6
ums_intr: data = e0 cc c9
ums0: disconnected
ums0: detached
ums0: ELECOM ELECOM M.A.P.P. series, rev 1.10/1.01, addr 2, iclass 3/1
ums_attach: bLength=7 bDescriptorType=5 bEndpointAddress=1-in bmAttributes=3 wMaxPacketSize=4 bInterval=10
ums0: 3 buttons and Z dir.
ums_attach: sc=0xc0a89800
ums_attach: X 8/8
ums_attach: Y 16/8
ums_attach: Z 24/8
ums_attach: B1 0/1
ums_attach: B2 1/1
ums_attach: B3 2/1
ums_attach: size=4, id=0
ums0: Spurious button up events
ums_intr: sc=0xc0a89800 status=6
ums_intr: data = 80 ff fc
ums_intr: sc=0xc0a89800 status=6
ums_intr: data = 80 ff fc
ums_intr: sc=0xc0a89800 status=6
ums_intr: data = 80 ff fc
ums0: at uhub1 port 2 (addr 2) disconnected
ums0: disconnected
ums0: detached
usbd_new_device bus=0xc0ca3000 port=2 depth=1 lowspeed=512
usbd_new_device: adding unit addr=2, rev=110, class=0, subclass=0, protocol=0, maxpacket=8, len=18, ls=1
usbd_find_quirk 0x056e/0x001e/101: 136
usbd_new_device: new dev (addr 2), dev=0xc0fca280, parent=0xc0c9d800
usbd_probe_and_attach: trying device specific drivers
usbd_probe_and_attach: no device specific driver found
usbd_probe_and_attach: looping over 1 configurations
usbd_set_config_index: (addr 2) attr=0xa0, selfpowered=0, power=100
usbd_set_config_index: set config 1
ums0: Elecom product 0x001e, rev 1.10/1.01, addr 2, iclass 3/1
ums_attach: bLength=7 bDescriptorType=5 bEndpointAddress=1-in bmAttributes=3 wMaxPacketSize=4 bInterval=10
ums0: 3 buttons and Z dir.
ums_attach: sc=0xc0a89800
ums_attach: X 8/8
ums_attach: Y 16/8
ums_attach: Z 24/8
ums_attach: B1 0/1
ums_attach: B2 1/1
ums_attach: B3 2/1
ums_attach: size=4, id=0
ums0: Spurious button up events
ums_intr: sc=0xc0a89800 status=6
ums_intr: data = 80 ff fc
ums_intr: sc=0xc0a89800 status=6
ums_intr: data = 80 ff fc
ums0: at uhub1 port 2 (addr 2) disconnected
ums0: disconnected
ums0: detached
usbd_new_device bus=0xc0ca3000 port=2 depth=1 lowspeed=512
usbd_new_device: adding unit addr=2, rev=110, class=0, subclass=0, protocol=0, maxpacket=8, len=18, ls=1
usbd_new_device: new dev (addr 2), dev=0xc0fca280, parent=0xc0c9d800
usbd_probe_and_attach: trying device specific drivers
usbd_probe_and_attach: no device specific driver found
usbd_probe_and_attach: looping over 1 configurations
usbd_set_config_index: (addr 2) attr=0xa0, selfpowered=0, power=100
usbd_set_config_index: set config 1
ums0: Logitech USB Mouse, rev 1.10/6.20, addr 2, iclass 3/1
ums_attach: bLength=7 bDescriptorType=5 bEndpointAddress=1-in bmAttributes=3 wMaxPacketSize=4 bInterval=10
ums0: 3 buttons and Z dir.
ums_attach: sc=0xc0a89800
ums_attach: X 8/8
ums_attach: Y 16/8
ums_attach: Z 24/8
ums_attach: B1 0/1
ums_attach: B2 1/1
ums_attach: B3 2/1
ums_attach: size=4, id=0
ums_intr: sc=0xc0a89800 status=6
ums_intr: data = 60 ff fc
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 ff 01
ums_intr: x:-1 y:-1 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 04 02
ums_intr: x:4 y:-2 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 08 00
ums_intr: x:8 y:0 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 07 00
ums_intr: x:7 y:0 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 07 00
ums_intr: x:7 y:0 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 07 ff
ums_intr: x:7 y:1 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 06 ff
ums_intr: x:6 y:1 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 05 ff
ums_intr: x:5 y:1 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 03 00
ums_intr: x:3 y:0 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 02 00
ums_intr: x:2 y:0 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 01 ff
ums_intr: x:1 y:1 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 02 00
ums_intr: x:2 y:0 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 02 fe
ums_intr: x:2 y:2 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 03 fe
ums_intr: x:3 y:2 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 03 fe
ums_intr: x:3 y:2 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 02 fd
ums_intr: x:2 y:3 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 01 00
ums_intr: x:1 y:0 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 ff 00
ums_intr: x:-1 y:0 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 fd 00
ums_intr: x:-3 y:0 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 fe 00
ums_intr: x:-2 y:0 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 fe 00
ums_intr: x:-2 y:0 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=0
ums_intr: data = 00 ff 00
ums_intr: x:-1 y:0 z:0 buttons:0x0
ums_intr: sc=0xc0a89800 status=6
ums_intr: data = 00 ff 00
ums0: at uhub1 port 2 (addr 2) disconnected
ums0: disconnected
ums0: detached
----------- usbdevs -v -------------
Controller /dev/usb0:
addr 1: self powered, config 1, UHCI root hub(0x0000), Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Controller /dev/usb1:
addr 1: self powered, config 1, UHCI root hub(0x0000), Intel(0x0000), rev 1.00
port 1 powered
port 2 addr 2: low speed, power 100 mA, config 1, product 0x001e(0x001e),
Elecom(0x056e), rev 1.01
Controller /dev/usb2:
addr 1: self powered, config 1, UHCI root hub(0x0000), Intel(0x0000), rev 1.00
port 1 powered
port 2 powered
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?03100212325316.38163>