Date: Sat, 13 Feb 1999 12:16:23 +0800 (PHT) From: "Francis Percival C. Favoreal" <dune@cats.edu.ph> To: Troy Settle <rewt@i-Plus.net> Cc: Dan Busarow <dan@dpcsys.com>, freebsd-isp@FreeBSD.ORG Subject: Re: PCI NE2000 problem Message-ID: <Pine.LNX.3.96.990213121438.3746D-100000@mayon.cats.edu.ph> In-Reply-To: <Pine.BSF.3.96.990212225203.11073B-100000@Radford.i-Plus.net>
next in thread | previous in thread | raw e-mail | index | archive | help
On Fri, 12 Feb 1999, Troy Settle wrote: > > On Fri, 12 Feb 1999, Dan Busarow wrote: > > > On Sat, 13 Feb 1999, Francis Percival C. Favoreal wrote: > > > de0 <Digital 21041 Ethernet> rev 33 int a irq 10 on pci0:13:0 > > > de0: 21041 [10Mb/s] pass 2.1 > > > de0: address 00:80:c8:59:e1:dc > > > vga0 <VGA-compatible display device> rev 16 int a irq 11 on pci0:15:0 > > > ed0 <NE2000 PCI Ethernet (RealTek 8029)> rev 0 int a irq 9 on pci0:16:0 > > > > PCI NE2000 should be detected at ed1, ed0 is ISA > > This depends entirely on the kernel configuration. I had a box with 2 > of these, and they are ed0 and ed1. Both worked perfectly. > > > > > > The kernel is compiled with ed0 config as, > > > > > > device ed? at pci0 port 0xff80 net irq 12 iomem 0xd800 vector edintr > > > > Wrong. You don't want that. Number 4 below is the one you want. > > > > > > I also tried the ff. ed0 configs then compiling the kernel for each: > > > > > > (1) device ed? at pci0 > > > (2) device ed? at pci? > > > (2) device ed? at pnp0 > > > (3) device ed? at pnp? > > > (4) device ed0 at isa? port 0x300 net irq 3 iomem 0xd8000 vector edintr > > > (5) device ed0 at isa? disable port 0x300 net irq 3 iomem 0xd8000 vector > > > edintr > > Try this: > > device ed0 > > no options, no nothing. This will get everything you need for this card > to work. > > > I did have the same problem as the original poster, reseating the card did > the trick... I guess it just wasn't comfortable the first time. > > If still no luck, try booting the generic kernel. It has the appropriate > drivers as well. The card will show up as either ed1 or 2. > > And, as a final, last resort, try swapping out the card for another. > Could have a bad card on your hands. > Thank you for those who responded. I finally got it to work. All that I did was to disable Plug-n-Play from the BIOS and all is well already. God, after months of thinking about this and it's finally over. -- riko sYsAd CATSNET To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-isp" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.LNX.3.96.990213121438.3746D-100000>