Date: Sun, 11 May 2014 10:06:27 +0000 (UTC) From: Christian Brueffer <brueffer@FreeBSD.org> To: src-committers@freebsd.org, svn-src-all@freebsd.org, svn-src-head@freebsd.org Subject: svn commit: r265875 - head/share/man/man4 Message-ID: <201405111006.s4BA6RN8089398@svn.freebsd.org>
next in thread | raw e-mail | index | archive | help
Author: brueffer Date: Sun May 11 10:06:27 2014 New Revision: 265875 URL: http://svnweb.freebsd.org/changeset/base/265875 Log: Typo fixes and some language/punctuation improvements. Modified: head/share/man/man4/lm75.4 Modified: head/share/man/man4/lm75.4 ============================================================================== --- head/share/man/man4/lm75.4 Sun May 11 09:54:38 2014 (r265874) +++ head/share/man/man4/lm75.4 Sun May 11 10:06:27 2014 (r265875) @@ -24,7 +24,7 @@ .\" .\" $FreeBSD$ .\" -.Dd March 7, 2014 +.Dd May 11, 2014 .Dt LM75 4 .Os .Sh NAME @@ -69,28 +69,28 @@ dev.lm75.0.shutdown: 0 Is the read-only value of the current temperature read by the sensor. .It Va dev.lm75.%d.thyst Sets the hysteresis temperature. -Once the temperature get over the overtemperature shutdown value (tos) -it need to drop bellow the hysteresis temperature to disable the output +Once the temperature gets over the overtemperature shutdown value (tos) +it needs to drop below the hysteresis temperature to disable the output (interrupt) pin again. .It Va dev.lm75.%d.tos Sets the overtemperature shutdown value. -Once the temperature get over this value the output pin will be enabled. +Once the temperature gets over this value the output pin will be enabled. The way the output (interrupt) pin works, depends on the mode configuration. .It Va dev.lm75.%d.faults Is the number of faults that must occur consecutively to activate the interrupt (output) pin. It can be set to 1, 2, 4, and 6. .It Va dev.lm75.%d.mode -Set the operation mode for the sensor interrupt pin. +Sets the operation mode for the sensor interrupt pin. It can be set to 'comparator' (default) or 'interrupt'. .It Va dev.lm75.%d.polarity -Set the polarity of the sensor interrupt pin. +Sets the polarity of the sensor interrupt pin. It can be set to 'active-low' (default) or 'active-high'. Please note that the output pin is an open-drain output and it needs a proper pull-up resistor to work. .It Va dev.lm75.%d.shutdown -When set to '1' it shutdown the sensor. -The temperature convertion stops but the sensor remains with its i2c bus +When set to '1' it shuts down the sensor. +The temperature conversion stops but the sensor remains with its i2c bus active, i.e., it can be woken up by setting this option to '0' again. .El .Pp @@ -124,7 +124,7 @@ On a .Xr device.hints 5 based system, like .Li MIPS , -these values are configurable for the +these values are configurable for .Nm : .Bl -tag -width ".Va hint.lm75.%d.addr" .It Va hint.lm75.%d.at @@ -168,7 +168,7 @@ property indicates which i2c address the .Nm is wired at. .Nm -temperature sensors can be wired to 8 different address, allowing up to 8 +temperature sensors can be wired to 8 different addresses, allowing up to 8 sensors on the same .Xr iicbus 4 . .El @@ -187,5 +187,5 @@ driver first appeared in .An -nosplit The .Nm -driver and this manual page was written by -.An Luiz Otavio O Souza Aq loos@FreeBSD.org +driver and this manual page were written by +.An Luiz Otavio O Souza Aq loos@FreeBSD.org .
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?201405111006.s4BA6RN8089398>