Date: Tue, 18 May 1999 20:02:31 -0500 (EST) From: Steven Ames <steve@virtual-voodoo.com> To: mtaylor@cybernet.com Cc: freebsd-current@freebsd.org Subject: Re: ed0/probe problem in 4.0-CURRENT Message-ID: <199905190102.UAA00351@virtual-voodoo.com> In-Reply-To: <XFMail.990518162959.mtaylor@cybernet.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Did all of that and a 'set boot_verbose'. Lots more data but I'm still not even seeing a probe for ethernet cards on the isa bus. I have 'ed1' and 'ep1' enabled in the kernel: device ed1 at isa? port 0x340 irq 10 iomem 0xd8000 device ep1 at isa? port 0x340 irq 10 And it is certainly not being detected. This behavior is new to 4.0-CURRENT. -Steve > At the second stage boot prompt, did you try "-v"? > > If you're at the 3rd stage boot prompt, use "boot -v". > > You'll get lots and lots of messages... > > > -Mark Taylor > NetMAX Developer > mtaylor@cybernet.com > > > On 18-May-99 Steven Ames wrote: > > > > Wow. I don't think that should ever happen but at this point I'll > > try a lot of things :) > > > > Tried it. didn't work. > > > > really, isn't there a way to enable more verbose probing so that > > it says 'ed0 not found at 0x280' or some such? > > > > > >> When I upgraded, my ed0 became ep0.... you might want to try that..... > >> > >> > >> Brandon Hicks - Gate Keeper Technologies > >> "Trixster" > >> bhicks@gatekeep.net > >> > >> > >> -----Original Message----- > >> From: Steven Ames <steve@virtual-voodoo.com> > >> To: freebsd-hackers@FreeBSD.ORG <freebsd-hackers@FreeBSD.ORG> > >> Date: Tuesday, May 18, 1999 10:10 AM > >> Subject: ed0/probe problem in 4.0-CURRENT > >> > >> > >> > > >> >Last night switched from 3.1 to 4.0. Smooth transition. The only > >> >error I've seen is one of my ethernet cards is no longer detected. > >> > > >> >In the previous kernel (3.1-STABLE) I had the following config > >> >line: > >> > > >> >device ed0 at isa? port 0x280 net irq 10 iomem 0xd8000 > >> > > >> >When the system booted it would detect 'ed1' on the PCI bus > >> >and 'ed0' on the isa bus. All was good. Under 4.0 things > >> >changed. > >> > > >> >Now when the system boots the PCI card is assigned to 'ed0' > >> >and then a message is printed saying 'ed0' is already used, > >> >using next number. But my ISA card isn't probed. I switched > >> >the ISA card to 'ed1'. The 'already used' message stopped > >> >but my ISA card is still not detected. > >> > > >> >The PCI card is: > >> > > >> >ed0: <NE2000 PCI Ethernet (RealTek 8029)> irq 11 at device 15.0 on pci0 > >> >ed0: address 52:54:00:dc:08:ca, type NE2000 (16 bit) > >> > > >> >the ISA card is MIA. I don't even get a 'ed1 not found at' message. > >> >Can anyone point me in the right direction? Or tell me how to > >> >make the device probing more verbose? > >> > > >> > -Steve > >> > > >> > > >> >To Unsubscribe: send mail to majordomo@FreeBSD.org > >> >with "unsubscribe freebsd-hackers" in the body of the message > >> > > >> > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > with "unsubscribe freebsd-hackers" in the body of the message > To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199905190102.UAA00351>