Date: Wed, 04 Jul 2001 08:28:12 -0700 From: "Greg Smith" <freebsd_mail@yahoo.com> To: "Eckhard Kantz" <Eckhard.Kantz@gmx.de> Cc: freebsd-mobile@freebsd.org Subject: Re: Realtek 8139 Message-ID: <200107040828120930.00165198@smtp.mail.yahoo.com> In-Reply-To: <00af01c10487$7bab3b40$be00a8c0@wegalink.net> References: <00af01c10487$7bab3b40$be00a8c0@wegalink.net>
next in thread | previous in thread | raw e-mail | index | archive | help
Eckhard, What type of computer do you have? I am very curious why you are using 0xc0000 for your pccard memory. Most computers have the video BIOS in that memory area, at least through 0xc7fff or 0xcbfff. [Two laptops I have detailed knowledge of use part of 0xcc000-0xcffff for pccard under Win95; four use memory in 0xd0000 and above.] Also, did you put the corresponding pccard_mem=0xc0000 entry in /etc/rc.conf? Greg -----Original Message----- >Could anyone provide some hints how to get a LevelOne PCMCIA card with >the Realtek 8139 chipset up >and running under FreeBSD 4.1? > >I tried one card 10 MBit and a second one 10/100 MBit but neither worked. >Accordingly to well known >hints I booted Windows and wrote down all parameters for memory, i/o and >irq used there. Next I >tried with pccardc to apply the same hardware parameters but it didn't >work. > >Please find dmesg below. In case of general problems with those network >cards, what other type of >10/100 MBit card could be recommended? > >Thanks for any advice. > >Eckhard >mailto:Eckhard.Kantz@gmx.de > > > >Copyright (c) 1992-2000 The FreeBSD Project. >Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. >FreeBSD 4.1-RELEASE #0: Fri Jul 28 13:01:29 GMT 2000 > inof@bestwishes.fromme.com:/usr/src/sys/compile/GENERIC >Timecounter "i8254" frequency 1193182 Hz >CPU: AMD-K6(tm) 3D processor (366.60-MHz 586-class CPU) > Origin = "AuthenticAMD" Id = 0x58c Stepping = 12 > Features=0x8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX> > AMD Features=0x80000800<SYSCALL,3DNow!> >real memory = 134217728 (131072K bytes) >config> di sn0 >config> di lnc0 >config> di le0 >config> di ie0 >config> di fe0 >config> di cs0 >config> di bt0 >config> di aic0 >config> di aha0 >config> di adv0 >config> en pcic0 >config> po pcic0 0x3e0 >config> ir pcic0 10 >config> iom pcic0 0xc0000 >config> f pcic0 0 >config> q >avail memory = 126398464 (123436K bytes) >Preloaded elf kernel "kernel" at 0xc040d000. >Preloaded userconfig_script "/boot/kernel.conf" at 0xc040d09c. >K6-family MTRR support enabled (2 registers) >md0: Malloc disk >npx0: <math processor> on motherboard >npx0: INT 16 interface >pcib0: <Host to PCI bridge> on motherboard >pci0: <PCI bus> on pcib0 >isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0 >isa0: <ISA bus> on isab0 >atapci0: <Intel PIIX4 ATA33 controller> port 0x1100-0x110f at device 7.1 >on pci0 >ata0: at 0x1f0 irq 14 on atapci0 >ata1: at 0x170 irq 15 on atapci0 >uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xf300-0xf31f irq 10 >at device 7.2 on pci0 >usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 >usb0: USB revision 1.0 >uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 >uhub0: 2 ports with 2 removable, self powered >uhub0: port 1 power on failed, IOERROR >uhub0: port 2 power on failed, IOERROR >ums0: Logitech Inc. iFeel Mouse , rev 1.00/1.01, addr 2, iclass 3/1 >ums0: 3 buttons and Z dir. >chip1: <Intel 82371AB Power management controller> port 0x1400-0x140f at >device 7.3 on pci0 >pci0: <S3 ViRGE MX graphics accelerator> at 8.0 >pcic-pci0: <TI PCI-1225 PCI-CardBus Bridge> at device 10.0 on pci0 >pcic-pci0: TI12XX PCI Config Reg: [speaker enable][pwr save][FUNC pci int >+ CSC serial isa irq] >pcic-pci1: <TI PCI-1225 PCI-CardBus Bridge> at device 10.1 on pci0 >pcic-pci1: TI12XX PCI Config Reg: [speaker enable][pwr save][FUNC pci int >+ CSC serial isa irq] >fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 >fdc0: FIFO enabled, 8 bytes threshold >fd0: <1440-KB 3.5" drive> on fdc0 drive 0 >atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 >atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 >kbd0 at atkbd0 >psm0: <PS/2 Mouse> irq 12 on atkbdc0 >psm0: model GlidePoint, device ID 0 >vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 >sc0: <System console> at flags 0x100 on isa0 >sc0: VGA <16 virtual consoles, flags=0x300> >pcic0: <VLSI 82C146> at port 0x3e0 iomem 0xc0000 irq 10 drq 0 on isa0 >pcic0: management irq 11 >pccard0: <PC Card bus -- kludge version> on pcic0 >pccard1: <PC Card bus -- kludge version> on pcic0 >sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 >sio0: type 16550A >sio1 at port 0x2f8-0x2ff irq 3 on isa0 >sio1: type 16550A >ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 >ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode >ppi0: <Parallel I/O> on ppbus0 >lpt0: <Printer> on ppbus0 >lpt0: Interrupt-driven port >plip0: <PLIP network interface> on ppbus0 >pccard: card inserted, slot 0 >pccard: card inserted, slot 1 >ata1-slave: ata_command: timeout waiting for intr >ata1-slave: identify failed >ad0: 19077MB <IBM-DJSA-220> [38760/16/63] at ata0-master using UDMA33 >acd0: CDROM <CD-224E> at ata1-master using PIO4 >Mounting root from ufs:/dev/ad0s3a > > > >To Unsubscribe: send mail to majordomo@FreeBSD.org >with "unsubscribe freebsd-mobile" in the body of the message _________________________________________________________ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200107040828120930.00165198>