Date: Thu, 26 Apr 2007 18:31:05 -0000 (GMT) From: jhall@vandaliamo.net To: "Derek Ragona" <derek@computinginnovations.com> Cc: jhall@vandaliamo.net, freebsd-questions@freebsd.org Subject: Re: FreeBSD 6.2 Boot Issue Message-ID: <2629.65.117.48.155.1177612265.squirrel@admintool.trueband.net> In-Reply-To: <6.0.0.22.2.20070426131910.026cd3e0@mail.computinginnovations.com> References: <2172.65.117.48.155.1177602567.squirrel@admintool.trueband.net> <6.0.0.22.2.20070426112024.026c7ec0@mail.computinginnovations.com> <2534.65.117.48.155.1177609975.squirrel@admintool.trueband.net> <6.0.0.22.2.20070426125610.026c3ea0@mail.computinginnovations.com> <2566.65.117.48.155.1177611388.squirrel@admintool.trueband.net> <6.0.0.22.2.20070426131910.026cd3e0@mail.computinginnovations.com>
next in thread | previous in thread | raw e-mail | index | archive | help
> At 01:16 PM 4/26/2007, jhall@vandaliamo.net wrote: >> > At 12:52 PM 4/26/2007, jhall@vandaliamo.net wrote: >> >>Both of those checked OK. Is it possible I have specified the C/H/S >> >>incorrectly during setup? >> >> >> >>Thanks, >> > >> > What is your type and model hard drive? Did you specify the geometry >> when >> > you ran sysinstall? >> > >> > How did you partition and slice the hard drive? >> > >> > >> > -Derek >> > >> > >> >>Derek, >> >>In the server I currently have three 376595-001 drives (146 GB serial >>SCSI) and three 432146-001 drives (300 GB serial SCSI). These drives are >>configured as a single drive in a RAID 5 configuration. >> >>I did not specify any geometry during the installation. >> >>I have the hard drive configured as a single partition with the >>appropriate lables (/, /var, /usr, /tmp and a swap area). >> >>Thanks for your help. > > Sounds like your system is not booting, but you're not getting any error > message. Check the boot order in your BIOS, and turn on diagnostic boot > messages if they are not turned on. > > Does they system boot from a CD ok? > > -Derek Yes, the system boots from CD just fine. And, it is able to run newfs during the install without any problems. The total size of the drive is 683.5 GB. The boot order in the BIOS is CD and then E200i controller. Thanks, Jay > > > > >>Jay >> >> >>Jay >> >> >> >> > At 10:49 AM 4/26/2007, jhall@vandaliamo.net wrote: >> >> >>I have installed FreeBSD 6.2 on an HP Proliant G5 server with an >> E200i >> >> >>Smart Controller installed. The installation was flawless. >> >> >> >> >> >>When I reboot the server after the installation, the boot loader >> >> screen >> >> >> is >> >> >>displayed. I press F1 and the system beeps and comes back to the >> boot >> >> >>loader prompt. >> >> >> >> >> >>What should I be looking at? I am at a loss since I usually end up >> >> with >> >> >>leftover hardware and this time I acutally got to purchase new >> >> hardware >> >> >>just for this project. >> >> >> >> >> >>Any suggestions would be greatly appreciated. >> >> >> >> >> >>Thanks for your help. >> >> > >> >> > Check your BIOS that you are ALLOWING the boot sector to be >> written. >> >> > >> >> > If that is OK, try disabling hyperthreading if that is turned on in >> >> your >> >> > BIOS. >> >> > >> >> > -Derek >> >> > >> >> > -- >> >> > This message has been scanned for viruses and >> >> > dangerous content by MailScanner, and is >> >> > believed to be clean. >> >> > MailScanner thanks transtec Computers for their support. >> >> > >> >> > >> >> >> >> >> >> >> >>-- >> >>This message has been scanned for viruses and >> >>dangerous content by MailScanner, and is >> >>believed to be clean. >> >>MailScanner thanks transtec Computers for their support. >> > >> > -- >> > This message has been scanned for viruses and >> > dangerous content by MailScanner, and is >> > believed to be clean. >> > MailScanner thanks transtec Computers for their support. >> > >> > >> >> >> >>-- >>This message has been scanned for viruses and >>dangerous content by MailScanner, and is >>believed to be clean. >>MailScanner thanks transtec Computers for their support. > > -- > This message has been scanned for viruses and > dangerous content by MailScanner, and is > believed to be clean. > MailScanner thanks transtec Computers for their support. > >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?2629.65.117.48.155.1177612265.squirrel>