Date: Fri, 24 May 2002 00:10:23 -0500 From: "Schroeder, Aaron" <ajschroeder@BUTLER.TMSComputers.com> To: 'Andrew Gallatin' <gallatin@cs.duke.edu>, "Schroeder, Aaron" <ajschroeder@BUTLER.TMSComputers.com> Cc: "'freebsd-alpha@freebsd.org'" <freebsd-alpha@FreeBSD.ORG> Subject: RE: DigitalServer 5305 install revisited... Message-ID: <61D76B69F719D61183D700062B000D4E0FBA@poseidon.butler.tmscomputers.com>
index | next in thread | raw e-mail
As promised, here is the captures that I took from the 5305 console, I HTH:
----------------------------------------------------------------------------
Here is the 5305 screen upon boot-up, or 'init':
starting console on CPU 0
sizing memory
0 256 MB DIMM
1 256 MB DIMM
2 256 MB DIMM
3 256 MB DIMM
4 256 MB DIMM
5 256 MB DIMM
6 256 MB DIMM
7 256 MB DIMM
starting console on CPU 1
probing IOD1 hose 1
bus 0 slot 1 - NCR 53C810
probing IOD0 hose 0
bus 0 slot 1 - PCEB
probing EISA Bridge, bus 1
bus 0 slot 2 - S3 Trio64/Trio32
bus 0 slot 3 - PCI-PCI Bridge
probing PCI-PCI Bridge, bus 2
bus 2 slot 0 - NCR 53C875
bus 2 slot 1 - NCR 53C875
bus 2 slot 2 - DECchip 21140-AA
** keyboard error **
configuring I/O adapters...
ncr0, hose 1, bus 0, slot 1
floppy0, hose 0, bus 1, slot 0
ncr1, hose 0, bus 2, slot 0
ncr2, hose 0, bus 2, slot 1
tulip0, hose 0, bus 2, slot 2
System temperature is 20 degrees C
DIGITAL Server 5000 Model 5305 6533A Console V6.0-4, 10-MAY-2001 10:11:42
P00>>>
----------------------------------------------------------------------------
--
Here it is after a 'sho config':
P00>>>sho config
Compaq Computer Corporation
DIGITAL Server 5000 Model 5305 6533A
Console V6.0-4 OpenVMS PALcode V1.21-2, Digital UNIX PALcode V1.23-2
Module Type Rev Name
System Motherboard 0 0000 mthrbrd0
Memory 256 MB DIMM 0 0000 mem0
Memory 256 MB DIMM 0 0000 mem1
Memory 256 MB DIMM 0 0000 mem2
Memory 256 MB DIMM 0 0000 mem3
Memory 256 MB DIMM 0 0000 mem4
Memory 256 MB DIMM 0 0000 mem5
Memory 256 MB DIMM 0 0000 mem6
Memory 256 MB DIMM 0 0000 mem7
CPU (4MB Cache) 3 0003 cpu0
CPU (4MB Cache) 3 0003 cpu1
Bridge (IOD0/IOD1) 600 0032 iod0/iod1
PCI Motherboard a 0000 saddle0
Bus 0 iod0 (PCI0)
Slot Option Name Type Rev Name
1 PCEB 4828086 0015 pceb0
2 S3 Trio64/Trio32 88115333 0044 vga0
3 PCI-PCI Bridge 241011 0002 pcb0
Bus 1 pceb0 (EISA Bridge connected to iod0, slot 1)
Slot Option Name Type Rev Name
Bus 2 pcb0 (PCI-PCI Bridge connected to iod0, slot 3)
Slot Option Name Type Rev Name
0 NCR 53C875 f1000 0004 ncr1
1 NCR 53C875 f1000 0004 ncr2
2 DECchip 21140-AA 91011 0022 tulip0
Bus 0 iod1 (PCI1)
Slot Option Name Type Rev Name
1 NCR 53C810 11000 0002 ncr0
P00>>>
----------------------------------------------------------------------------
--
Finally, here is the output after I 'boot dka500'. The CD that I am using is
4.5-RELEASE:
P00>>>boot dka500
(boot dka500.5.0.1.1 -flags a)
block 0 of dka500.5.0.1.1 is a valid boot block
reading 375 blocks from dka500.5.0.1.1
bootstrap code read in
Building FRU table
base = 200000, image_start = 0, image_bytes = 2ee00
initializing HWRPB at 2000
initializing page table at 1f2000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Console: SRM firmware console
VMS PAL rev: 0x4000200010115
OSF PAL rev: 0x4000200020117
Switch to OSF PAL code succeeded.
FreeBSD/alpha SRM CD9660 boot, Revision 1.0
(murray@axpbuilder.freebsdmall.com, Mon Jan 28 16:18:52 GMT 2002)
Memory: 2097152 k
Loading /boot/defaults/loader.conf
/kernel data=0x406778+0x2acb8 syms=[0x8+0x4e360+0x8+0x38928]
\
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [kernel]...
Entering kernel at 0xfffffc0000331460...
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
fatal kernel trap:
trap entry = 0x2 (memory management fault)
a0 = 0x60
a1 = 0x1
a2 = 0x0
pc = 0xfffffc00005b2a70
ra = 0xfffffc00005fa0c8
curproc = 0
panic: trap
Uptime: 0s
----------------------------------------------------------------------------
-------
If you need more information than this, just let me know what to provide.
OBTW - I tried booting the server WITHOUT the network cable attached and the
system errors with the same panic, in other words, no difference. EWA0 is
set to Auto-Negotiate.
TIA,
AJ Schroeder
-----Original Message-----
From: Andrew Gallatin [mailto:gallatin@cs.duke.edu]
Sent: Thursday, May 23, 2002 8:31 AM
To: Schroeder, Aaron
Cc: 'freebsd-alpha@freebsd.org'
Subject: Re: DigitalServer 5305 install revisited...
Schroeder, Aaron writes:
> Hello all,
>
> I have just powered on a DigitalServer 5305 and I am trying to install
> 4.5-RELEASE onto it. Up on booting the CD, I get this error message:
>
> fatal kernel trap:
> trap entry = 0x2 (memory management fault)
> a0 = 0x0 a1 = 0x1
> a2 = 0xffffffffffffffff
> pc = 0x0
> ra = 0xfffffc00004b16cc
> curproc = 0
> panic: trap
> Uptime: 0s
>
A PC of 0x0 implies that something followed a NULL function pointer.
There have been sporadic reports of a potentially similar problem by
people who netboot.
Does it help if you unplug the network cable durning boot?
How soon after booting do you see this? Can you show us the rest of
the boot messages you see, please?
Drew
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-alpha" in the body of the message
help
Want to link to this message? Use this
URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?61D76B69F719D61183D700062B000D4E0FBA>