Date: Wed, 19 Jul 2000 21:18:39 +0200 From: Wilko Bulte <wkb@freebie.demon.nl> To: FreeBSD-alpha mailing list <freebsd-alpha@freebsd.org> Subject: Re: test results for Lynx (AS2100A) Message-ID: <20000719211839.A2061@freebie.demon.nl>
next in thread | raw e-mail | index | archive | help
[forgot to cc: -alpha]
On Tue, Jul 18, 2000 at 10:50:19AM -0700, Matthew Jacob wrote:
> boot verbose, please...
Here you are. I have booted a SCSI disk with 4.1RC as of Jul 18 on it
that I pre-installed on a AS2100.
Wilko
Script started on Wed Jul 19 13:16:28 2000
P00>>>sho dev
dka600.6.0.2001.0 DKA600 RRD43 1084
dkb0.0.0.9.0 DKB0 RZ29B 0014
dkb600.6.0.9.0 DKB600 RRD46 0557
dra0.0.0.1003.0 DRA0 5 Member RAID 5
drb0.0.0.2006.0 DRB0 2 Member RAID 1
drb1.0.0.2006.0 DRB1 2 Member RAID 1
drb2.0.0.2006.0 DRB2 2 Member RAID 1
dva0.0.0.1000.0 DVA0 RX26/RX23
ewa0.0.0.7.0 EWA0 00-00-F8-23-16-31
pka0.7.0.2001.0 PKA0 SCSI Bus ID 7
pkb0.7.0.9.0 PKB0 SCSI Bus ID 7 5.57
P00>>>boot dkb0
(boot dkb0.0.0.9.0 -flags A)
block 0 of dkb0.0.0.9.0 is a valid boot block
reading 15 blocks from dkb0.0.0.9.0
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 1e00
initializing HWRPB at 2000
initializing page table at 7ff0000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
VMS PAL rev: 0x4000700010538
OSF PAL rev: 0x4000c0002012d
Switch to OSF PAL code succeeded.
FreeBSD/alpha SRM disk boot, Revision 0.3
(root@miata.wbnet, Tue Jul 18 21:05:09 GMT 2000)
Memory: 131072 k
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [kernel] in 9 seconds... Booting [kernel] in 8 seconds... Booting [kernel]...
Entering kernel at 0xfffffc000032b280...
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 18jul00-41rc #0: Tue Jul 18 22:19:33 GMT 2000
root@miata.wbnet:/usr/src/sys/compile/GENERIC
DEC AlphaServer 2100A
AlphaServer 2100A 4/200, 190MHz
8192 byte page size, 1 processor.
CPU: EV4 (21064) major=2 minor=1
OSF PAL rev: 0x4000c0002012d
real memory = 132046848 (128952K bytes)
Physical memory chunk(s):
0x00710000 - 0x07fe5fff, 126705664 bytes (15467 pages)
avail memory = 122511360 (119640K bytes)
Preloaded elf kernel "kernel" at 0xfffffc00006f4000.
md0: Malloc disk
Creating DISK md0
found-> vendor=0x8086, dev=0x0482, revid=0x15
class=00-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x1011, dev=0x0001, revid=0x02
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=2 secondarybus=2
found-> vendor=0x1011, dev=0x0002, revid=0x24
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=68
map[10]: type 1, range 32, base 00010100, size 7
map[14]: type 1, range 32, base 81111000, size 7
found-> vendor=0x1077, dev=0x1020, revid=0x05
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=76
map[10]: type 1, range 32, base 00010000, size 8
map[14]: type 1, range 32, base 81110000, size 12
found-> vendor=0x0000, dev=0x0000, revid=0x00
class=ff-ff-ff, hdrtype=0x7f, mfdev=1
subordinatebus=0 secondarybus=0
intpin=[, irq=33
found-> vendor=0x0000, dev=0x0000, revid=0x00
class=00-00-00, hdrtype=0x0f, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x0000, dev=0x0000, revid=0x00
class=ff-ff-ff, hdrtype=0x7f, mfdev=1
subordinatebus=0 secondarybus=0
intpin=[, irq=32
found-> vendor=0x0000, dev=0x0000, revid=0x00
class=00-00-00, hdrtype=0x0f, mfdev=0
subordinatebus=0 secondarybus=0
pci0: <PCI bus> on pcib0
isab0: <Intel 82375EB PCI-EISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
pcib1: <DEC 21050 PCI-PCI bridge> at device 3.0 on pci0
found-> vendor=0x1000, dev=0x0001, revid=0x11
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=60
map[10]: type 1, range 32, base 00005000, size 8
map[14]: type 1, range 32, base 81004000, size 8
found-> vendor=0x1069, dev=0x0001, revid=0x00
class=01-04-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=80
map[10]: type 1, range 32, base 00005400, size 7
pci2: <PCI bus> on pcib1
sym0: <810a> port 0x5000-0x50ff mem 0x81004000-0x810040ff irq 60 at device 1.0 on pci2
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: open drain IRQ line driver
sym0: using LOAD/STORE-based firmware.
sym0: initial SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 00/00/00/00/00/00
sym0: final SCNTL3/DMODE/DCNTL/CTEST3/4/5 = (hex) 03/c2/a0/00/08/00
sym0: Delay (GEN=11): 258 msec, 34450 KHz
sym0: Delay (GEN=11): 283 msec, 31407 KHz
sym0: Delay (GEN=11): 283 msec, 31407 KHz
sym0: interrupting at T2 irq 60
pci2: <unknown card> (vendor=0x1069, dev=0x0001) at 6.0 irq 80
de0: <Digital 21040 Ethernet> port 0x10100-0x1017f mem 0x81111000-0x8111107f irq 68 at device 7.0 on pci0
de0: interrupting at T2 irq 68
de0: DEC 21040 [10Mb/s] pass 2.4
de0: address 00:00:f8:23:16:31
bpf: de0 attached
Qlogic ISP Driver, FreeBSD Version 4.4, Core Version 1.16
isp0: <Qlogic ISP 1020/1040 PCI SCSI Adapter> port 0x10000-0x100ff mem 0x81110000-0x81110fff irq 76 at device 9.0 on pci0
isp0: using Memory space register mapping
isp0: set PCI line size to 16
isp0: interrupting at T2 irq 76
isp0: Ultra Mode Capable
isp0: Board Revision 1040B, resident F/W Revision 5.57.1
isp0: Last F/W revision was 5.57.1
isp0: 256 max I/O commands supported
pci0: <unknown card> (vendor=0x0000, dev=0x0000) at 12.0 irq 33
pci0: <unknown card> (vendor=0x0000, dev=0x0000) at 12.4
pci0: <unknown card> (vendor=0x0000, dev=0x0000) at 13.0 irq 32
pci0: <unknown card> (vendor=0x0000, dev=0x0000) at 13.4
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: interrupting at T2 irq 6
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbd0: atkbd0, generic (0), config:0x0, flags:0x1f0000
atkbd0: interrupting at T2 irq 1
psm0: current command byte:0061
kbdc: TEST_AUX_PORT status:0074
kbdc: DIAGNOSE status:0075
psm: keyboard controller failed.
kbdc: TEST_KBD_PORT status:0077
psm: keyboard port failed.
psm0: the aux port is not functioning (116).
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xb8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 04 02 14 01 05 03 07 38 3c 3a 3e 39
3d 3b 3f 04 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x0>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0
Calibrating clock(s) ... PCC clock: 190008696 Hz (firmware 190114068 Hz)
sio0: configured irq 4 not in bitmap of probed irqs 0x1
sio0: irq maps: 0 0x1 0x1 0x1
sio0 at port 0x3f8-0x3ff irq 4 on isa0
sio0: type 16550A, console
sio0: interrupting at T2 irq 4
sio1: reserved for low-level i/o
isa_probe_children: probing PnP devices
Timecounter "alpha" frequency 190008696 Hz
bpf: sl0 attached
bpf: ppp0 attached
bpf: lo0 attached
bpf: gif0 attached
bpf: gif1 attached
bpf: gif2 attached
bpf: gif3 attached
bpf: faith0 attached
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
isp0: driver initiated bus reset of bus 0
de0: enabling 10baseT port
halted CPU 0
halt code = 1
operator initiated halt
PC = fffffc00003a2e98
P00>>> ~
[EOT]
wilklt#
wilklt#exit
Script done on Wed Jul 19 13:23:46 2000
--
Wilko Bulte http://www.freebsd.org
wilko@freebsd.org http://www.nlfug.nl
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-alpha" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20000719211839.A2061>