Date: Mon, 3 Jun 2019 20:50:42 +0900 (JST) From: Mori Hiroki <yamori813@yahoo.co.jp> To: Ronald Klop <ronald-lists@klop.ws>, "freebsd-arm@freebsd.org" <freebsd-arm@freebsd.org>, "freebsd-stable@freebsd.org" <freebsd-stable@freebsd.org> Subject: Re: boot 11.3-BETA1 hangs om armv5 Message-ID: <1442525240.1981975.1559562642958.JavaMail.yahoo@jws704001.mail.kks.yahoo.co.jp> In-Reply-To: <op.z2gsinvwkndu52@sjakie> References: <op.z2gsinvwkndu52@sjakie>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi. I build and flash on arm/ralink today by CURRENT. arm/ralink is hangup at same point too. Hiroki Mori ----- Original Message ----- > From: Ronald Klop <ronald-lists@klop.ws> > To: freebsd-arm@freebsd.org; "freebsd-stable@freebsd.org" <freebsd-stable@freebsd.org> > Cc: > Date: 2019/5/28, Tue 05:00 > Subject: boot 11.3-BETA1 hangs om armv5 > > Was running "FreeBSD 11.2-RELEASE-p4 (SHEEVAPLUG) #4 r339336M: Sat Oct 13 > 23:31:51 CEST 2018". > Compiled 11.3-BETA1, installed kernel.bin in /boot/msdos and started it. > Output below. It hangs. I guess in starting the random/entropy stuff. > > Any thoughts or advise? > Don't spend to much time on it, I'm happy to phase it out. > > Regards, > Ronald. > > > Rebooting... > > __ __ _ _ > | \/ | __ _ _ ____ _____| | | > | |\/| |/ _` | '__\ \ / / _ \ | | > | | | | (_| | | \ V / __/ | | > |_| |_|\__,_|_| \_/ \___|_|_| > _ _ ____ _ > | | | | | __ ) ___ ___ | |_ > | | | |___| _ \ / _ \ / _ \| __| > | |_| |___| |_) | (_) | (_) | |_ > \___/ |____/ \___/ \___/ \__| > ** MARVELL BOARD: SHEEVA PLUG LE > > U-Boot 1.1.4 (Mar 19 2009 - 16:06:59) Marvell version: 3.4.16 > > U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE80 > > Soc: 88F6281 A0 (DDR2) > CPU running @ 1200Mhz L2 running @ 400Mhz > SysClock = 400Mhz , TClock = 200Mhz > > DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 > DRAM CS[0] base 0x00000000 size 256MB > DRAM CS[1] base 0x10000000 size 256MB > DRAM Total size 512MB 16bit width > Flash: 0 kB > Addresses 8M - 0M are saved for the U-Boot usage. > Mem malloc Initialization (8M - 7M): Done > NAND:512 MB > > CPU : Marvell Feroceon (Rev 1) > > Streaming disabled > Write allocate disabled > > > USB 0: host mode > PEX 0: interface detected no Link. > Net: egiga0 [PRIME], egiga1 > Hit any key to stop autoboot: 0 > (Re)start USB... > USB: scanning bus for devices... 4 USB Device(s) found > scanning bus for storage devices... 1 Storage Device(s) found > reading kernel.bin > . > ........................................................................................................................................................................................................................................................................................................................................................................................................................................ > > 4345316 bytes read > ## Starting application at 0x00900000 ... > Copyright (c) 1992-2019 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 11.3-BETA1 #0 r348277M: Sun May 26 14:17:08 CEST 2019 > builder@rpi3:/data/src/obj-11.3/arm.arm/data/src/11.3/sys/SHEEVAPLUG > arm > FreeBSD clang version 8.0.0 (tags/RELEASE_800/final 356365) (based on LLVM > 8.0.0) > CPU: Feroceon 88FR131 rev 1 (**unknown 4** core) > Little-endian DC enabled IC disabled WA disabled DC streaming enabled > BTB disabled L2 enabled L2 prefetch enabled > WB enabled LABT branch prediction disabled > 16KB/32B 4-way instruction cache > 16KB/32B 4-way write-back-locking-C data cache > real memory = 536866816 (511 MB) > avail memory = 518778880 (494 MB) > SOC: Marvell 88F6281 rev A0, TClock 200MHz > Instruction cache prefetch enabled, data cache prefetch enabled > 256KB 4-way set-associative write-through unified L2 cache > random: entropy device external interface > _______________________________________________ > freebsd-arm@freebsd.org mailing list > https://lists.freebsd.org/mailman/listinfo/freebsd-arm > To unsubscribe, send any mail to "freebsd-arm-unsubscribe@freebsd.org" >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1442525240.1981975.1559562642958.JavaMail.yahoo>