Date: Mon, 15 Sep 2003 18:46:22 -0500 From: "Secureplay" <secureplay@sbcglobal.net> To: "'Matthew N. Dodd'" <winter@jurai.net> Cc: freebsd-hardware@freebsd.org Subject: RE: 4.8 on Proliant 8500 Message-ID: <002001c37be3$928ea380$d20a0a0a@jvstice.ops.mil> In-Reply-To: <20030913192510.W27896@sasami.jurai.net>
next in thread | previous in thread | raw e-mail | index | archive | help
Thanks for the suggestion. I gave it another try and tried out a number
of different types of OSs in the Compaq configuration. Some worked =
better
than
others (Linux, Windows 2000 and a few others worked well) others such as
MSDOS=20
locked up during the SMP initialization. I even went and reassigned some
IRQs by
hand.
Still no go. Those cards are invisible. I am about to give up and =
install
some
flavor of Linux. For my particular purpose, any Unix variant is okay, so
it's no
biggie. However I'd have liked to have a freebsd-only setup for this
particular
project (this is one of three servers, and the others -- Proliant DL360 =
G2
boxes --
run fbsd 4.8 without problems, and with the same Intel NIC.)
Just for curiosity's sake, here's my dmesg. If anyone sees something
suspicious,
please let me know. Yes, there is a problem with the SMP handling, but =
if
that
was the cuplrity, the cards should be seen in uniproc mode... (?).. =
There is
also
something wrong with the cdr, but that could be a dying drive.
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.8-RELEASE #0: Thu Sep 11 16:01:12 CDT 2003
root@myhostname:/usr/obj/usr/src/sys/kernelconf02
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (500.01-MHz 686-class CPU)
Origin =3D "GenuineIntel" Id =3D 0x672 Stepping =3D 2
=20
Features=3D0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE=
,MCA,
CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory =3D 2684321792 (2621408K bytes)
config> di bt0
config> di aic0
config> di aha0
config> di adv0
config> q
avail memory =3D 2609360896 (2548204K bytes)
Changing APIC ID for IO APIC #0 from 0 to 8 on chip
Programming 35 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 2, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000
cpu2 (AP): apic id: 1, version: 0x00040011, at 0xfee00000
cpu3 (AP): apic id: 3, version: 0x00040011, at 0xfee00000
cpu4 (AP): apic id: 4, version: 0x00040011, at 0xfee00000
cpu5 (AP): apic id: 5, version: 0x00040011, at 0xfee00000
cpu6 (AP): apic id: 6, version: 0x00040011, at 0xfee00000
cpu7 (AP): apic id: 7, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 8, version: 0x00220011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc0368000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc036809c.
Preloaded elf module "if_em.ko" at 0xc03680ec.
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib3: <DEC 21154 PCI-PCI bridge> at device 3.0 on pci0
pci1: <PCI bus> on pcib3
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x3000-0x301f mem
0xf7d00000-0xf7dfffff,0xf4ff0000-0xf4ff0fff irq 9 at device 4.0 on pci1
fxp0: Ethernet address 00:08:c7:a6:e0:0f
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: <Intel Pro 10/100B/100+ Ethernet> port 0x3020-0x303f mem
0xf7c00000-0xf7cfffff,0xf4fe0000-0xf4fe0fff irq 9 at device 5.0 on pci1
fxp1: Ethernet address 00:08:c7:a6:e0:8f
inphy1: <i82555 10/100 media interface> on miibus1
inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <unknown card> (vendor=3D0x0e11, dev=3D0xa0f7) at 11.0 irq 10
pci0: <unknown card> (vendor=3D0x0e11, dev=3D0xa0f0) at 12.0
pci0: <ATI Mach64-GV graphics accelerator> at 13.0
ida0: <Compaq Integrated Array controller> port 0x2400-0x24ff mem
0xf5000000-0xf5ffffff,0xf6000000-0xf6ffffff irq 11 at device 14.0 on =
pci0
ida0: drives=3D1 firm_rev=3D1.50
idad0: <Compaq Logical Drive> on ida0
idad0: 17343MB (35520480 sectors), blocksize=3D512
isab0: <ServerWorks IB6566 PCI to ISA bridge> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Generic PCI ATA controller> port
0x2820-0x282f,0x2818-0x281b,0x2810-0x2817,0x2808-0x280b,0x2800-0x2807 at
device 15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <unknown card> (vendor=3D0x118c, dev=3D0x1117) at 20.0
pci0: <unknown card> (vendor=3D0x118c, dev=3D0x1116) at 20.1
pcib1: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib1
pcib2: <Host to PCI bridge> on motherboard
pci3: <PCI bus> on pcib2
orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xcbfff,0xe8000-0xedfff,0xee000-0xeffff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on =
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse Explorer, device ID 4
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on =
isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: Broken MP table detected: 8254 is not connected to IOAPIC #0 =
intpin
2
APIC_IO: routing 8254 via 8259 and IOAPIC #0 intpin 0
ata0-slave: ATAPI identify retries exceeded
SMP: AP CPU #6 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #7 Launched!
SMP: AP CPU #5 Launched!
SMP: AP CPU #4 Launched!
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
acd0: MODE_SENSE_BIG command timeout - resetting
ata0: resetting devices .. ata0-slave: ATAPI identify retries exceeded
done
acd0: read data overrun 6/0
acd0: read data overrun 6/0
acd0: read data overrun 6/0
acd0: read data overrun 4/0
acd0: CDROM <CD-224E> at ata0-master PIO4
Mounting root from ufs:/dev/idad0s1a
=20
-----Original Message-----
From: Matthew N. Dodd [mailto:winter@jurai.net]=20
Sent: Saturday, September 13, 2003 6:26 PM
To: Secureplay
Cc: 'Barney Wolff'; freebsd-hardware@freebsd.org
Subject: RE: 4.8 on Proliant 8500
On Sat, 13 Sep 2003, Secureplay wrote:
> I did try other slots. Originally I had it in the tertiary (64-bit)=20
> bus, it being a 64-bit card, then I tried the slots on primary and=20
> secondary as well. No luck. :(
Try playing with the Compaq config util and change the version of the =
OS.
Its likely that the mode you have it in now requires the OS to identify =
and
initialize the PCI-PCI bridge, or to initialize an additional Host to =
PCI
bridge.
--=20
| Matthew N. Dodd | '78 Datsun 280Z | '75 Volvo 164E | FreeBSD/NetBSD =
|
| winter@jurai.net | 2 x '84 Volvo 245DL | ix86,sparc,pmax =
|
| http://www.jurai.net/~winter | For Great Justice! | ISO8802.5 4ever=20
| |
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?002001c37be3$928ea380$d20a0a0a>