Date: Thu, 22 Sep 2005 12:27:36 +0100 From: Joao Barros <joao.barros@gmail.com> To: "Peter D. Quilty" <pdquilty@adelphia.net> Cc: Peter Jeremy <PeterJeremy@optushome.com.au>, freebsd-stable@freebsd.org, freebsd-mobile@freebsd.org Subject: Re: High interrupts w/ Cisco 350 card Message-ID: <70e8236f050922042731f06600@mail.gmail.com> In-Reply-To: <1127387609.1092.2.camel@pdq-laptop> References: <1127259847.1266.101.camel@pdq-laptop> <20050921080126.GK40237@cirb503493.alcatel.com.au> <1127387609.1092.2.camel@pdq-laptop>
next in thread | previous in thread | raw e-mail | index | archive | help
On 9/22/05, Peter D. Quilty <pdquilty@adelphia.net> wrote: > On Wed, 2005-09-21 at 18:01 +1000, Peter Jeremy wrote: > > > On Tue, 2005-Sep-20 19:44:07 -0400, Peter D. Quilty wrote: > > >I'm running 5.4-RELEASE-p6 on a Toshiba Tecra M2 laptop. My network > > >card is a Cisco 350 PCMCIA card. I'm experiencing a very high rate of > > >interrupts during heavy network traffic. > > > > Not quite. "vmstat -i" reports 173 interrupts/sec. That's not high. > > "systat -iostat" shows a ludicrously high interrupt load though. > > > > I notice that almost all the hardware on your laptop maps to irq 11 - > > that's undesirable. Can you convince your BIOS to use different > > interrupt mappings? > > > > No, the PCI bus is hardcoded to use only irqs 10 & 11. The video card > uses 10 and everything else shares 11. > > > > > This Cisco card works fine in every other laptop I have. > > > > What OS? > > > > All are running FreeBSD 5.4-RELEASE. > > > > > I suspect it might be a cardbus problem, but I don't > > >know how to resolve it or troubleshoot it any further. > > > > The PCCard bus is fairly atrocious (basically ISA) but isn't that bad. > > I can get roughly wire speed from a 10baseT NIC without serious CPU > > strain on a P-233 laptop. > > > > Have you tried anything other that FreeBSD 5.4 on your Tecra? > > > > No, I haven't. It is my primary laptop and I would prefer not to have > to load another OS merely for testing. > > > > >interrupt total rate > > ... > > >irq11: cbb0 cbb1+++ 6773905 173 > > ... > > > /0 /10 /20 /30 /40 /50 /60 /70 /80 /90 /100 > > >cpu user|XXXXX > > > nice| > > > system|X > > >interrupt|XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX > > > idle|XXX > > ... > I also have an Cisco Aironet 350 and the only time I had such an issue was connecting to a WPA enabled AP and a recent (couple of months) firmware update from Cisco corrected this issue. Given that you're using 5.4 and WPA is only coming out in 6.0 I know this is a long shot but I would try updating the firmware of the card. Heck, every update I do gives me more speed and stability :) -- Joao Barros
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?70e8236f050922042731f06600>