Date: Tue, 29 Mar 2005 00:50:08 +0800 From: John Mok <jmok@attglobal.net> To: Julian Elischer <julian@elischer.org> Cc: Roman Kurakin <rik@cronyx.ru> Subject: Re: HOWTO connect MCI using Netgraph + Frame Relay with Digi SYNC/570i Message-ID: <424835C0.9070603@attglobal.net> In-Reply-To: <42404B15.5040605@elischer.org> References: <42344AF7.6070701@attglobal.net> <423C72A1.7060000@cronyx.ru> <4240497D.5030304@attglobal.net> <42404B15.5040605@elischer.org>
next in thread | previous in thread | raw e-mail | index | archive | help
After issuing the following commands :-
#ngctl mkpeer sync_ar0: frame_relay rawdata downstream
#ngctl mkpeer sync_ar0:rawdata lmi dlci0 ansi
#ngctl mkpeer sync_ar0:rawdata rfc1490 dlci16 rfc1490
#ngctl mkpeer sync_ar0:rawdata dlci16 rl0 inet inet
#ifconfig ng0 1.2.3.4 5.6.7.8
ifconfig: interface ng0 does not exist
The command ifconfig shows :-
rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet6 fe80::207:40ff:fe09:f09%rl0 prefixlen 64 scopeid 0x1
inet 192.168.255.254 netmask 0xffffff00 broadcast 192.168.255.255
ether 00:07:40:09:0f:09
media: Ethernet autoselect (none)
status: no carrier
xl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=9<RXCSUM,VLAN_MTU>
inet6 fe80::201:3ff:fec1:9c58%xl0 prefixlen 64 scopeid 0x2
ether 00:01:03:c1:9c:58
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
xl1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=9<RXCSUM,VLAN_MTU>
inet6 fe80::201:3ff:fe34:61af%xl1 prefixlen 64 scopeid 0x3
inet 192.168.16.254 netmask 0xffffff00 broadcast 192.168.16.255
ether 00:01:03:34:61:af
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5
inet 127.0.0.1 netmask 0xff000000
and the command "ngctl list" shows :-
There are 4 total nodes:
Name: ngctl811 Type: socket ID: 00000011 Num hooks: 0
Name: <unnamed> Type: frame_relay ID: 00000004 Num hooks: 1
Name: sync_ar1 Type: sync_ar ID: 00000002 Num hooks: 0
Name: sync_ar0 Type: sync_ar ID: 00000001 Num hooks: 1
Would it be the problem that I test it with cable disconnected from the
modem (i.e.CSU/DSU)?
Thanks a lot.
John Mok
Julian Elischer wrote:
> did the last command do anything?
>
> please show the output of:
> ifconfig
> ngctl list
>
>
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?424835C0.9070603>