Date: Mon, 18 Feb 2002 14:04:57 +0000 From: dom@happygiraffe.net (Dominic Mitchell) To: Peter Wemm <peter@wemm.org> Cc: alpha@freebsd.org, current@freebsd.org Subject: Re: OK, who broke alpha this time? :-/ Message-ID: <20020218140457.A518@cathbad.happygiraffe.net> In-Reply-To: <20020218060734.314FE3809@overcee.wemm.org>; from peter@wemm.org on Sun, Feb 17, 2002 at 10:07:34PM -0800 References: <20020218060734.314FE3809@overcee.wemm.org>
next in thread | previous in thread | raw e-mail | index | archive | help
--x+6KMIRAuhnl3hBn Content-Type: text/plain; charset=us-ascii Content-Disposition: inline On Sun, Feb 17, 2002 at 10:07:34PM -0800, Peter Wemm wrote: > ... > sio0 at port 0x3f8-0x3ff irq 4 on isa0 > sio0: type 16550A, console > sio0: interrupting at ISA irq 4 > sio1: reserved for low-level i/o > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > Timecounter "i8254" frequency 1193182 Hz > ata0-slave: timeout waiting for interrupt > ata0-slave: ATAPI identify failed > acd0: CDROM <CD-540E> at ata0-master PIO4 > Waiting 2 seconds for SCSI devices to settle > Mounting root from ufs:/dev/da0a > da0 at ahc0 bus 0 target 0 lun 0 > da0: <SEAGATE ST318404LW 0006> Fixed Direct Access SCSI-3 device > da0: 80.000MB/s transfers (40.000MHz, offset 63, 16bit), Tagged Queueing Enabled > da0: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C) > da1 at ahc0 bus 0 target 1 lun 0 > da1: <IBM DMVS18V 0250> Fixed Direct Access SCSI-3 device > da1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled > da1: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C) > ^T > load: 0.16 cmd: init 8 [inode] 0.00u 0.00s 0% 416k > ^T > load: 0.16 cmd: init 8 [inode] 0.00u 0.00s 0% 416k > [forever] > > http://people.freebsd.org/~peter/alphadmesg.txt > > It seems that locking has been hosed somehow. Just to confirm, I've just seen this on my i386 laptop (sony Z600TEK), too, which has a fresh cvsup and build from about 2.5 hours ago. Attached is a dmesg from my kernel.old which I've just manage to boot and a kernel config. -Dom --x+6KMIRAuhnl3hBn Content-Type: text/plain; charset=us-ascii Content-Disposition: attachment; filename="CATHBAD.dmesg" Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.0-CURRENT #32: Mon Feb 11 14:48:12 GMT 2002 root@cathbad.happygiraffe.net:/usr/obj/usr/src/sys/CATHBAD Preloaded elf kernel "/boot/kernel.old/kernel" at 0xc0370000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc03700ac. Timecounter "i8254" frequency 1193182 Hz Timecounter "TSC" frequency 694834844 Hz CPU: Pentium III/Pentium III Xeon/Celeron (694.83-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x683 Stepping = 3 Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 268369920 (262080K bytes) avail memory = 257699840 (251660K bytes) Pentium Pro MTRR support enabled Using $PIR table, 7 entries at 0xc00fdf50 npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <SONY Z3 > on motherboard Timecounter "ACPI" frequency 3579545 Hz acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_tz0: <thermal zone> on acpi0 acpi_button0: <Power Button> on acpi0 acpi_pcib0: <Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <PCI bus> on acpi_pcib0 pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pci1: <display, VGA> at device 0.0 (no driver attached) isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 ATA33 controller> port 0xfc90-0xfc9f at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pci0: <serial bus, USB> at device 7.2 (no driver attached) pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached) pci0: <serial bus, FireWire> at device 8.0 (no driver attached) pci0: <multimedia, audio> at device 9.0 (no driver attached) pci0: <simple comms> at device 10.0 (no driver attached) pci0: <network, ethernet> at device 11.0 (no driver attached) acpi_pcib0: device is routed to IRQ 9 pcic0: <Ricoh RL5C475 PCI-CardBus Bridge> irq 9 at device 12.0 on pci0 pcic0: PCI Memory allocated: 0x44000000 pccard0: <PC Card bus (classic)> on pcic0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model GlidePoint, device ID 0 acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A ppc0 port 0x778-0x77a,0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port acpi_cmbat0: <Control method Battery> on acpi0 acpi_acad0: <AC adapter> on acpi0 ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it pcic: pcic0 already exists; skipping it ppc: ppc0 already exists; skipping it sc: sc0 already exists; skipping it sio: sio0 already exists; skipping it vga: vga0 already exists; skipping it orm0: <Option ROMs> at iomem 0xdc000-0xdffff,0xc0000-0xcffff on isa0 sc0: <System console> on isa0 sc0: VGA <16 virtual consoles, flags=0x200> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 pmtimer0 on isa0 sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled acpi_cpu: CPU throttling enabled, 8 steps from 100% to 12.5% ad0: 19077MB <IBM-DJSA-220> [38760/16/63] at ata0-master UDMA33 Mounting root from ufs:/dev/ad0s2a Fatal trap 12: page fault while in kernel mode fault virtual address = 0x14 fault code = supervisor write, page not present instruction pointer = 0x8:0xc0169cc3 stack pointer = 0x10:0xccbd2b2c frame pointer = 0x10:0xccbd2b3c code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, def32 1, gran 1 processor eflags = interrupt enabled, resume, IOPL = 0 current process = 63 (mount_msdosfs) panic: from debugger panic: from debugger Uptime: 29s pfs_vncache_unload(): 1 entries remaining Automatic reboot in 15 seconds - press a key on the console to abort --> Press a key on the console to reboot, --> or switch off the system now. Rebooting... Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.0-CURRENT #32: Mon Feb 11 14:48:12 GMT 2002 root@cathbad.happygiraffe.net:/usr/obj/usr/src/sys/CATHBAD Preloaded elf kernel "/boot/kernel.old/kernel" at 0xc038c000. Preloaded elf module "/boot/kernel.old/msdosfs.ko" at 0xc038c0ac. Preloaded elf module "/boot/kernel.old/procfs.ko" at 0xc038c15c. Preloaded elf module "/boot/kernel/pseudofs.ko" at 0xc038c20c. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc038c2bc. Timecounter "i8254" frequency 1193182 Hz Timecounter "TSC" frequency 694836968 Hz CPU: Pentium III/Pentium III Xeon/Celeron (694.84-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x683 Stepping = 3 Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 268369920 (262080K bytes) avail memory = 257585152 (251548K bytes) Pentium Pro MTRR support enabled Using $PIR table, 7 entries at 0xc00fdf50 npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <SONY Z3 > on motherboard Timecounter "ACPI" frequency 3579545 Hz acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_tz0: <thermal zone> on acpi0 acpi_button0: <Power Button> on acpi0 acpi_pcib0: <Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <PCI bus> on acpi_pcib0 pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pci1: <display, VGA> at device 0.0 (no driver attached) isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 ATA33 controller> port 0xfc90-0xfc9f at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pci0: <serial bus, USB> at device 7.2 (no driver attached) pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached) pci0: <serial bus, FireWire> at device 8.0 (no driver attached) pci0: <multimedia, audio> at device 9.0 (no driver attached) pci0: <simple comms> at device 10.0 (no driver attached) pci0: <network, ethernet> at device 11.0 (no driver attached) acpi_pcib0: device is routed to IRQ 9 pcic0: <Ricoh RL5C475 PCI-CardBus Bridge> irq 9 at device 12.0 on pci0 pcic0: PCI Memory allocated: 0x44000000 pccard0: <PC Card bus (classic)> on pcic0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model GlidePoint, device ID 0 acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A ppc0 port 0x778-0x77a,0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port acpi_cmbat0: <Control method Battery> on acpi0 acpi_acad0: <AC adapter> on acpi0 ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it pcic: pcic0 already exists; skipping it ppc: ppc0 already exists; skipping it sc: sc0 already exists; skipping it sio: sio0 already exists; skipping it vga: vga0 already exists; skipping it orm0: <Option ROMs> at iomem 0xdc000-0xdffff,0xc0000-0xcffff on isa0 sc0: <System console> on isa0 sc0: VGA <16 virtual consoles, flags=0x200> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 pmtimer0 on isa0 sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled acpi_cpu: CPU throttling enabled, 8 steps from 100% to 12.5% ad0: 19077MB <IBM-DJSA-220> [38760/16/63] at ata0-master UDMA33 Mounting root from ufs:/dev/ad0s2a WARNING: / was not properly dismounted WARNING: /home was not properly dismounted WARNING: /usr was not properly dismounted WARNING: /var was not properly dismounted uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xfca0-0xfcbf irq 9 at device 7.2 on pci0 usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhub1: Philips Semiconductors hub, class 9/0, rev 1.10/1.10, addr 2 uhub1: 3 ports with 3 removable, self powered fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xfc40-0xfc7f mem 0xfec00000-0xfecfffff,0xfedf6000-0xfedf6fff irq 9 at device 11.0 on pci0 fxp0: Ethernet address 08:00:46:0d:3b:34 inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto --x+6KMIRAuhnl3hBn Content-Type: text/plain; charset=us-ascii Content-Disposition: attachment; filename=CATHBAD # # CATHBAD -- Dom's laptop # machine i386 ident CATHBAD cpu I686_CPU maxusers 32 #To statically compile in device wiring instead of /boot/device.hints #hints "GENERIC.hints" #Default places to look for devices. makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols options INET #InterNETworking options INET6 #IPv6 communications protocols options FFS #Berkeley Fast Filesystem options SOFTUPDATES #Enable FFS soft updates support options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!] options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI options UCONSOLE #Allow users to grab the console options KTRACE #ktrace(1) support options SYSVSHM #SYSV-style shared memory options SYSVMSG #SYSV-style message queues options SYSVSEM #SYSV-style semaphores options P1003_1B #Posix P1003_1B real-time extensions options _KPOSIX_PRIORITY_SCHEDULING options KBD_INSTALL_CDEV # install a CDEV entry in /dev # Debugging for use in -current options DDB #Enable the kernel debugger ## options UFS_EXTATTR ## options UFS_EXTATTR_AUTOSTART ## options UFS_ACL options UFS_DIRHASH # Allow us to mount windows shares. Relies on userland port net/smbfs. #options NETSMB #options NETSMBCRYPTO #options LIBICONV #options SMBFS device isa device pci #options PCI_ENABLE_IO_MODES # Enable pci resources left off by a "lazy BIOS" # ATA and ATAPI devices device ata device atadisk # ATA disk drives device atapicd # ATAPI CDROM drives options ATA_STATIC_ID #Static device numbering # SCSI peripherals device scbus # SCSI bus (required) device da # Direct Access (disks) device cd # CD device pass # Passthrough device (direct SCSI access) # atkbdc0 controls both the keyboard and the PS/2 mouse device atkbdc 1 # At keyboard controller device atkbd # at keyboard device psm # psm mouse device vga # VGA screen # splash screen/screen saver device splash # syscons is the default console driver, resembling an SCO console device sc 1 # Floating point support - do not disable. device npx # Power management support (see NOTES for more options) device apm # Add suspend/resume support for the i8254. device pmtimer # PCCARD (PCMCIA) support device card # pccard bus device pcic # PCMCIA bridge ## # NEWCARD support, which doesn't appear to like my modem... ## device pccbb ## device pccard ## device cardbus # Serial (COM) ports device sio # 8250, 16[45]50 based serial ports # Parallel port device ppc device ppbus # Parallel port bus (required) device lpt # Printer # Pseudo devices - the number indicates how many units to allocate. device random # Entropy device device loop # Network loopback device ether # Ethernet support device pty # Pseudo-ttys (telnet etc) device gif # IPv6 and IPv4 tunneling device faith # IPv6-to-IPv4 relaying (translation) # The `bpf' device enables the Berkeley Packet Filter. # Be aware of the administrative consequences of enabling this! device bpf # Berkeley packet filter --x+6KMIRAuhnl3hBn-- To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020218140457.A518>