Date: Mon, 29 Mar 2004 23:15:16 -0500 From: "Michael E. Mercer" <mmercer@nc.rr.com> To: freebsd-stable@freebsd.org Cc: Julian Elischer <julian@elischer.org> Subject: Re: USB2 device Message-ID: <1080620116.348.3.camel@fast.mmercer.com> In-Reply-To: <1080619808.348.1.camel@fast.mmercer.com> References: <Pine.BSF.4.21.0403291600580.29660-100000@InterJet.elischer.org> <1080619808.348.1.camel@fast.mmercer.com>
next in thread | previous in thread | raw e-mail | index | archive | help
The SlimHub does get seen by the EHCI device. later Michael On Mon, 2004-03-29 at 23:10, Michael E. Mercer wrote: > Julian, > > It works if I plug it directly into a usb port on my PC. But it does not > get seen if I plug it into a SIIG SlimHub 2.0. > > Any ideas? > Michael > > On Mon, 2004-03-29 at 19:17, Julian Elischer wrote: > > here's mine: > > Copyright (c) 1992-2003 The FreeBSD Project. > > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > > The Regents of the University of California. All rights > > reserved. > > FreeBSD 4.8-RELEASE-p15 #13: Mon Mar 29 13:34:08 PST 2004 > > > > root@teraserver.dev.vicor-nb.com:/usr/obj/usr/prod/system/VERS_4_8_BRANCH/src/sys/VICOR > > Timecounter "i8254" frequency 1193182 Hz > > Timecounter "TSC" frequency 2800107696 Hz > > CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz (2800.11-MHz 686-class CPU) > > Origin = "GenuineIntel" Id = 0xf25 Stepping = 5 > > > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > Hyperthreading: 2 logical CPUs > > real memory = 1073659904 (1048496K bytes) > > avail memory = 1040945152 (1016548K bytes) > > Preloaded elf kernel "k2" at 0xc0456000. > > Pentium Pro MTRR support enabled > > md0: Malloc disk > > Using $PIR table, 12 entries at 0xc00f23c0 > > npx0: <math processor> on motherboard > > npx0: INT 16 interface > > pcib0: <Host to PCI bridge> on motherboard > > pci0: <PCI bus> on pcib0 > > pcib1: <PCI to PCI bridge (vendor=8086 device=2561)> at device 1.0 on > > pci0 > > pci1: <PCI bus> on pcib1 > > uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xd800-0xd81f > > irq 5 at device 29.0 on pci0 > > usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0 > > usb0: USB revision 1.0 > > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > > uhub0: 2 ports with 2 removable, self powered > > uscanner0: Hewlett-Packard HP ScanJet 6200C, rev 1.00/1.00, addr 2 > > uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xd400-0xd41f > > irq 9 at device 29.1 on pci0 > > usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1 > > usb1: USB revision 1.0 > > uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > > uhub1: 2 ports with 2 removable, self powered > > uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xd000-0xd01f > > irq 9 at device 29.2 on pci0 > > usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2 > > usb2: USB revision 1.0 > > uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > > uhub2: 2 ports with 2 removable, self powered > > ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf7000000-0xf70003ff irq > > 11 at device 29.7 on pci0 > > ehci_pci_attach: companion usb0 > > ehci_pci_attach: companion usb1 > > ehci_pci_attach: companion usb2 > > usb3: EHCI version 1.0 > > usb3: companion controllers, 2 ports each: usb0 usb1 usb2 > > usb3: <EHCI (generic) USB 2.0 controller> on ehci0 > > usb3: USB revision 2.0 > > uhub3: (0x8086) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 > > uhub3: 6 ports with 6 removable, self powered > > pcib2: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on > > pci0 > > pci2: <PCI bus> on pcib2 > > bfe0: <Broadcom BCM4401 Fast Ethernet> mem 0xf6800000-0xf6801fff irq 10 > > at device 5.0 on pci2 > > bfe0: Ethernet address: 00:0e:a6:18:a4:72 > > miibus0: <MII bus> on bfe0 > > ukphy0: <Generic IEEE 802.3u media interface> on miibus0 > > ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > > pci2: <ATI Mach64-GR graphics accelerator> at 9.0 irq 9 > > ahc0: <Adaptec 2940A Ultra SCSI adapter> port 0xb400-0xb4ff mem > > 0xf4000000-0xf4000fff irq 9 at device 10.0 on pci2 > > aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs > > pcm0: <Creative CT5880-E> port 0xb000-0xb03f irq 10 at device 12.0 on > > pci2 > > pcm0: <unknown ac97 codec> (id=0x454d4328) > > fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0xa800-0xa83f mem > > 0xf3000000-0xf301ffff,0xf3800000-0xf3800fff irq 9 at device 13.0 on pci2 > > fxp0: Ethernet address 00:02:b3:ea:e7:d6 > > inphy0: <i82555 10/100 media interface> on miibus1 > > inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > > isab0: <PCI to ISA bridge (vendor=8086 device=24c0)> at device 31.0 on > > pci0 > > isa0: <ISA bus> on isab0 > > atapci0: <Intel ICH4 ATA100 controller> port > > 0xf000-0xf00f,0-0x3,0-0x7,0-0x3,0-0x7 irq 9 at device 31.1 on pci0 > > ata0: at 0x1f0 irq 14 on atapci0 > > ata1: at 0x170 irq 15 on atapci0 > > pcm1: <Intel 82801DB (ICH4)> port 0x9400-0x943f,0x9800-0x98ff mem > > 0xf2000000-0xf20000ff,0xf2800000-0xf28001ff irq 9 at device 31.5 on pci0 > > pcm1: <unknown ac97 codec> (id=0x41445370) > > orm0: <Option ROMs> at iomem > > 0xc0000-0xc7fff,0xc8000-0xc87ff,0xcc000-0xcd7ff on isa0 > > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on > > isa0 > > fdc0: FIFO enabled, 8 bytes threshold > > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > > kbd0 at atkbd0 > > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > > psm0: model Generic PS/2 mouse, device ID 0 > > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on > > isa0 > > sc0: <System console> at flags 0x100 on isa0 > > sc0: VGA <16 virtual consoles, flags=0x100> > > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > > sio0: type 16550A, console > > sio1 at port 0x2f8-0x2ff irq 3 on isa0 > > sio1: type 16550A > > ppc0: <Parallel port> at port 0x378-0x37f on isa0 > > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > > ppc0: FIFO with 16/16/16 bytes threshold > > lpt0: <Printer> on ppbus0 > > lpt0: Polled port > > IP packet filtering initialized, divert enabled, rule-based forwarding > > enabled, default to accept, logging disabled > > IPsec: Initialized Security Association Processing. > > ad0: 117246MB <Maxtor 6Y120L0> [238216/16/63] at ata0-master UDMA100 > > Waiting 4 seconds for SCSI devices to settle > > uscanner0: at uhub0 port 2 (addr 2) disconnected > > uscanner0: detached > > uscanner0: Hewlett-Packard HP ScanJet 6200C, rev 1.00/1.00, addr 2 > > Mounting root from ufs:/dev/ad0s1a > > umass0: LEXAR MEDIA JUMPDRIVE PRO, rev 2.00/0.00, addr 2 > > da0 at umass-sim0 bus 0 target 0 lun 0 > > da0: <LEXAR JUMPDRIVE PRO 0> Removable Direct Access SCSI-2 device > > da0: 650KB/s transfers > > da0: 246MB (503808 512 byte sectors: 64H 32S/T 246C) > > (da0:umass-sim0:0:0:0): READ(6)/WRITE(6) not supported, increasing > > minimum_cmd_size to 10. > > > > > > jtest# usbdevs -v > > Controller /dev/usb0: > > addr 1: low speed, self powered, config 1, UHCI root hub(0x0000), > > Intel(0x0000), rev 1.00 > > port 1 powered > > port 2 addr 2: low speed, self powered, config 1, HP ScanJet > > 6200C(0x0201), Hewlett-Packard(0x03f0), rev 1.00 > > Controller /dev/usb1: > > addr 1: low speed, self powered, config 1, UHCI root hub(0x0000), > > Intel(0x0000), rev 1.00 > > port 1 powered > > port 2 powered > > Controller /dev/usb2: > > addr 1: low speed, self powered, config 1, UHCI root hub(0x0000), > > Intel(0x0000), rev 1.00 > > port 1 powered > > port 2 powered > > Controller /dev/usb3: > > addr 1: low speed, self powered, config 1, EHCI root hub(0x0000), > > (0x8086)(0x0000), rev 1.00 > > port 1 powered > > port 2 powered > > port 3 powered > > port 4 powered > > port 5 powered > > port 6 addr 2: low speed, power 200 mA, config 1, JUMPDRIVE > > PRO(0x0200), LEXAR MEDIA(0x05dc), rev 0.00 > > jtest# > > jtest# dd if=/dev/da0 of=/dev/null bs=64k > > Mar 29 19:01:32 jtest /k2: (da0:umass-sim0:0:0:0): READ(6)/WRITE(6) not > > supported, increasing minimum_cmd_size to 10. > > Mar 29 19:01:32 jtest /k2: (da0:umass-sim0:0:0:0): READ(6)/WRITE(6) not > > supported, increasing minimum_cmd_size to 10. > > 3936+0 records in > > 3936+0 records out > > 257949696 bytes transferred in 47.199914 secs (5465046 bytes/sec) > > jtest# > > jtest# cat VICOR > > machine i386 > > cpu I586_CPU > > cpu I686_CPU > > ident VICOR > > maxusers 256 > > > > makeoptions DEBUG=-g > > > > options INET #InterNETworking > > options FFS #Berkeley Fast Filesystem > > options FFS_ROOT #FFS usable as root device [keep > > this!] > > options SOFTUPDATES #Enable FFS soft updates support > > options UFS_DIRHASH #Faster in large dirs (memory > > tradeoff) > > options MFS #Memory Filesystem > > options NFS #Network Filesystem > > options MSDOSFS #MSDOS Filesystem > > options CD9660 #ISO 9660 Filesystem > > options PROCFS #Process filesystem > > options COMPAT_43 #Compatible with BSD 4.3 [KEEP > > THIS!] > > options SCSI_DELAY=4000 #Delay (in ms) before probing SCSI > > options UCONSOLE #Allow users to grab the console > > options USERCONFIG #boot -c editor > > options SYSVSHM #SYSV-style shared memory > > options SYSVMSG #SYSV-style message queues > > options SYSVSEM #SYSV-style semaphores > > options P1003_1B #Posix P1003_1B real-time > > extensions > > options _KPOSIX_PRIORITY_SCHEDULING > > options KBD_INSTALL_CDEV # install a CDEV entry in /dev > > options INCLUDE_CONFIG_FILE # Include this file in kernel > > options DDB > > #options DDB_UNATTENDED > > options KTRACE #kernel tracing > > options IPDIVERT #Divert sockets > > options IPSEC #IP security > > options IPSEC_ESP #IP security (crypto; define w/ > > IPSEC) > > options IPFIREWALL #Packet firewall > > options IPFIREWALL_DEFAULT_TO_ACCEPT #Only block on firewall > > machines > > options IPFIREWALL_FORWARD > > options MAXDSIZ=(2047*1024*1024) > > > > #options SMP # Symmetric MultiProcessor > > Kernel > > #options APIC_IO # Symmetric (APIC) I/O > > #options HTT # HyperThreading Technology > > > > device isa > > device pci > > > > device fdc0 at isa? port IO_FD1 irq 6 drq 2 > > device fd0 at fdc0 drive 0 > > > > device ata0 at isa? port IO_WD1 irq 14 > > device ata1 at isa? port IO_WD2 irq 15 > > device ata > > device atadisk # ATA disk drives > > device atapicd # ATAPI CDROM drives > > options ATA_STATIC_ID #Static device numbering > > > > device ahc # AHA2940 and onboard AIC7xxx devices > > device dpt # DPT Smartcache - See LINT for > > options! > > device mlx > > device mly > > device twe > > > > device scbus # SCSI bus (required) > > device da # Direct Access (disks) > > device sa # Sequential Access (tape etc) > > device cd # CD > > device pass # Passthrough dev (direct SCSI > > access) > > device pt > > device ch > > device ses > > > > device atkbdc0 at isa? port IO_KBD > > device atkbd0 at atkbdc? irq 1 flags 0x1 > > device psm0 at atkbdc? irq 12 > > > > device vga0 at isa? > > > > pseudo-device splash > > > > device sc0 at isa? flags 0x100 > > > > device npx0 at nexus? port IO_NPX irq 13 > > > > device sio0 at isa? port IO_COM1 flags 0x10 irq 4 > > device sio1 at isa? port IO_COM2 irq 3 > > > > device ppc0 at isa? > > device ppbus > > device lpt > > > > device em # Intel PRO/1000 adapter Gigabit > > Ethernet Card (``Wiseman'') > > device miibus > > device bfe # Broadcom BCM440x > > device bge # Broadcom BCM570x (``Tigon > > III'') > > device fxp > > > > device pcm > > > > device xdcp > > device cy0 > > #options CY_PCI_FASTINTR # Use with cy_pci unless irq is > > shared > > > > pseudo-device loop # Network loopback > > pseudo-device ether # Ethernet support > > pseudo-device pty # Pseudo-ttys (telnet etc) > > pseudo-device md # Memory "disks" > > pseudo-device bpf #Berkeley packet filter > > pseudo-device vn > > pseudo-device gif #IPv6 and IPv4 tunneling > > pseudo-device speaker > > > > # USB support > > device ehci # EHCI PCI->USB interface > > device uhci # UHCI PCI->USB interface > > device ohci # OHCI PCI->USB interface > > device usb # USB Bus (required) > > device ugen # Generic > > device uhid # "Human Interface Devices" > > #device ukbd # Keyboard > > device ulpt # Printer > > device umass # Disks/Mass storage - Requires > > scbus and da > > device ums # Mouse > > device uscanner # Scanners > > > > device firewire # Generic > > device fwe # Generic > > device sbp # Generic > > > > jtest# > > > > ignore the xdcp entry... it's local. > > > > I don;t see any mention of cam or SCSI in your config.. > > umass requires cam asn they implement SCSI-over-USB > > to get the disk function. > > > > This is not however perfect.. I get hangs on boot if the drive is > > already inserted, and sometimes it doesn't notice that it is removed... > > > > but it does give me 5.4MBytes/sec which is > than teh theoretical > > maximum of about 1.5MB/sec for USB1.1 > > > > julian > > > > > > _______________________________________________ > > freebsd-stable@freebsd.org mailing list > > http://lists.freebsd.org/mailman/listinfo/freebsd-stable > > To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org" > > _______________________________________________ > freebsd-stable@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-stable > To unsubscribe, send any mail to "freebsd-stable-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1080620116.348.3.camel>