Skip site navigation (1)Skip section navigation (2)
Date:      Fri, 15 Jul 2005 16:06:11 +0900
From:      Pyun YongHyeon <pyunyh@gmail.com>
To:        Muzaffar Ariff <mus.bsd@gmail.com>
Cc:        freebsd-multimedia@freebsd.org
Subject:   Re: ESS Maestro3 no sound
Message-ID:  <20050715070611.GA13095@rndsoft.co.kr>
In-Reply-To: <8eb2b81050714233235ff3aad@mail.gmail.com>
References:  <20050629043027.GB8832@rndsoft.co.kr> <42C2B94F.2010708@samsco.org> <20050701014258.GE17058@rndsoft.co.kr> <8eb2b810507110203229b46b@mail.gmail.com> <20050711092238.GC858@rndsoft.co.kr> <8eb2b8105071217477e240667@mail.gmail.com> <20050713011018.GB4479@rndsoft.co.kr> <8eb2b81050713204179cb710c@mail.gmail.com> <20050714045121.GB8764@rndsoft.co.kr> <8eb2b81050714233235ff3aad@mail.gmail.com>

next in thread | previous in thread | raw e-mail | index | archive | help
On Fri, Jul 15, 2005 at 02:32:54PM +0800, Muzaffar Ariff wrote:
 > Ooohhh thats a whole lot of questions, I'll try my best to answer it :)
 > 
 > > Thanks for your report. It seems that you have other issues not
 > > known to me. Does the driver prints timeout message such as
 > > "pcm0:play:0: play interrupt timeout, channel dead"?
 > Nope, I checked in /var/log/messages and there is nothing wrong with
 > it or that line. In fact before I never had that problem.
 > 
 > > xmms plays songs with normal speed?(i.e. just no sound)
 > Yup, xmms plays my mp3s fine, its just no sound is coming out of it.
 > I've tried mute & unmute from the function button on the laptop and
 > increasing the volume, but nothing seems to happen.
 > 

I see. It sounds like Codec issues.

 > > Without loading ACPI do you suffer from the same problem?
 > If I get you right ACPI means Adv. Configuration and Power Management
 > support right? I can unload an ACPI from /boot/loader.conf but there
 > are several ACPIs, which one you want me to unload?
 > 
You can disable ACPI in loader. If you use beastie menu you can find
a menu item that disables ACPI(probably Safe Mode). If you don't use
beastie menu then you will see a message "Hit [Enter] to boot
immediately, or any other key for command prompt." In that screen,
just press SPACE bar to get OK prompt. Once you get the prompt enter     
"set hint.acpi.0.disabled=1" and then enter "boot". Note, depending
on your system booting kernel without ACPI may not work at all.

 > > Could show me "pciconf -lv" output for your ESS card?
 > pcm0@pci0:8:0:  class=0x040100 card=0x00b11028 chip=0x1998125d rev=0x10 hdr=0x00
 >     vendor   = 'ESS Technology'
 >     device   = 'ES1980 Maestro-3 PCI Audio Accelerator'
 >     class    = multimedia
 >     subclass = audio
 > 
 > > If you can run "pciconf -lv", locate a line somthing like
 > > pcm0@pciX:Y:Z. Then show me output of
 > > "pciconf -r pciX:Y:Z 0:ff" before and after loading the drier.
 > After loading the driver this is what i got:
 > #pciconf -r pci0:8:0 0:ff
 > 1998125d 
 > 
 > Before (I simply recompiled and install the old maestro3.c driver) I got this:
 > # pciconf -r pci0:8:0 0:ff
 > 1998125d 
 >  
Oops.. It's typo. It should be read "pciconf -r pci0:8:0 0:0xff".

 > Both before and after looks the same. Hope thats what you want. 
 > 
-- 
Regards,
Pyun YongHyeon



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20050715070611.GA13095>