Date: Sat, 25 Oct 2003 14:12:16 +0200 From: Andreas Klemm <andreas@freebsd.org> To: current@freebsd.org Subject: bge0 driver "PHY read timeout" and pccardd not finding PCMCIA card, DELL Latitude D600, with current of yesterday Message-ID: <20031025121215.GA70499@titan.klemm.apsfilter.org>
next in thread | raw e-mail | index | archive | help
Hi,
some severe problems with a brand new DELL Latitude D600 laptop.
It has a Broadcom BCM5702 Gigabit Ethernet, ASIC rev. 0x1002,
on board.
On the 1st boot FreeBSD 5.1-current from a self made CD-ROM
(-current from yesterday) paniced during 1st boot from CD (just
before installation). It had a Fritz PCMCIA card inserted.
The next installation attempt from CD was, trying to boot
without ACPI, which succeeded.
Then after installation and reboot it turns out that I can boot
without panic even with ACPI enabled.
But it might be due to one change, I replaced the Fritz ISDN card
with a 3COM 3CCFE575BT, since the broadcom bge0 interface doesn't
run properly.
In short, these are the problems:
1. bge0 driver doesn't find PHY
Laptop is connected with a working shielded CAT 5 cable to
a DLINK DI 804 DSL router who has a builtin 10/100 4-port switch
supporting full and half duplex cabability.
2. pcmcia card is not recognized. 3COM 3CCFE575BT
This card runs fine in -current on a Toshiba Satellite PRO 4360.
You see pccardd -d output at the end of the log.
3. Panic with ACPI enabled and Fritz ISDN card inserted
AVM Fritz!Card PCMCIA v2.0 (info on the label)
I booted now with serial com console and with boot_verbose set
At the end you see=20
- "uname -a" command- and
- "pccardd -d" output
Any chance to get that fixed ?
Or do you think I'll better using FreeBSD 4.9 with that hardware ?
Has 4.9 broadcom support ?
boot
-=08\=08|=08/=08-=08\=08|=08/=08-=08\=08|=08/=08-=08\=08|=08/=08-=08\=08|=
=08/=08-=08\=08|=08/=08-=08/boot/kernel/acpi.ko text=3D0x3b3dc \=08|=08/=08=
-=08\=08|=08/=08-=08\=08|=08/=08-=08\=08|=08/=08data=3D0x168c+0xee0 -=08sym=
s=3D[0x4+0x5b30\=08+0x4+0x78b8|=08/=08]
-=08\=08|=08/=08-=08\=08|=08SMAP type=3D01 base=3D0000000000000000 len=3D00=
0000000009f000
SMAP type=3D02 base=3D000000000009f000 len=3D0000000000001000
SMAP type=3D01 base=3D0000000000100000 len=3D000000001feae000
SMAP type=3D02 base=3D000000001ffae000 len=3D0000000000052000
SMAP type=3D02 base=3D00000000feda0000 len=3D0000000000060000
SMAP type=3D02 base=3D00000000ffb00000 len=3D0000000000500000
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.1-20031024-SNAP #0: Sat Oct 25 03:04:22 GMT 2003
root@titan.klemm.apsfilter.org:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a61000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a611cc.
Calibrating clock(s) ... i8254 clock: 1193119 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1395477939 Hz
CPU: Intel(R) Pentium(R) M processor 1400MHz (1395.48-MHz 686-class CPU)
Origin =3D "GenuineIntel" Id =3D 0x695 Stepping =3D 5
Features=3D0xa7e9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMO=
V,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,TM,PBE>
real memory =3D 536535040 (511 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c26000 - 0x000000001f688fff, 514207744 bytes (125539 pages)
avail memory =3D 511598592 (487 MB)
bios32: Found BIOS32 Service Directory header at 0xc00ffe80
bios32: Entry =3D 0xffe90 (c00ffe90) Rev =3D 0 Len =3D 1
pcibios: PCI BIOS entry at 0xf0000+0xc97e
pnpbios: Found PnP BIOS data at 0xc00fe2d0
pnpbios: Entry =3D f0000:e2f4 Rev =3D 1.0
pnpbios: Event flag at 4b4
Other BIOS signatures found:
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL CPi R > on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x80010014
pci_open(1a): mode1res=3D0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=3D060000] [hdr=3D00] is there (id=3D33408086)
pcibios: BIOS version 2.10
Using $PIR table, 9 entries at 0xc00fc590
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 29 A 0x60 3 4 5 6 7 9 10 11 12 14 15
embedded 0 29 B 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 0 29 C 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 0 29 D 0x6b 3 4 5 6 7 9 10 11 12 14 15
embedded 0 30 A 0x60 3 4 5 6 7 9 10 11 12 14 15
embedded 0 30 B 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 0 30 C 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 0 30 D 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 0 31 A 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 0 31 B 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 1 0 A 0x60 3 4 5 6 7 9 10 11 12 14 15
embedded 2 0 A 0x62 3 4 5 6 7 9 10 11 12 14 15
embedded 2 1 A 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 2 1 B 0x63 none
embedded 2 3 A 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 2 3 B 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 8 0 A 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 8 0 B 0x63 3 4 5 6 7 9 10 11 12 14 15
embedded 8 1 A 0x61 3 4 5 6 7 9 10 11 12 14 15
embedded 8 1 B 0x63 3 4 5 6 7 9 10 11 12 14 15
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
ACPI timer looks GOOD min =3D 3, max =3D 3, width =3D 0
ACPI timer looks GOOD min =3D 3, max =3D 3, width =3D 0
ACPI timer looks GOOD min =3D 3, max =3D 3, width =3D 0
ACPI timer looks GOOD min =3D 3, max =3D 3, width =3D 0
ACPI timer looks GOOD min =3D 3, max =3D 3, width =3D 0
ACPI timer looks GOOD min =3D 3, max =3D 3, width =3D 0
ACPI timer looks GOOD min =3D 3, max =3D 3, width =3D 0
ACPI timer looks GOOD min =3D 3, max =3D 3, width =3D 0
ACPI timer looks GOOD min =3D 3, max =3D 3, width =3D 0
ACPI timer looks GOOD min =3D 3, max =3D 3, width =3D 0
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_cmbat1: <Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
\_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.31.0
\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 0.31.1
\_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 0.31.2
\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 0.31.3
\_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.29.0
\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 0.29.1
\_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 0.29.2
\_SB_.PCI0.LNKH irq 11: [ 3 4 5 6 7 9 10 11 12 14 15] low,level,shar=
able 0.29.3
\_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.1.0
\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 0.1.1
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.31.0
\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 0.31.1
\_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 0.31.2
\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 0.31.3
\_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.29.0
\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 0.29.1
\_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 0.29.2
\_SB_.PCI0.LNKH irq 11: [ 3 4 5 6 7 9 10 11 12 14 15] low,level,shar=
able 0.29.3
\_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.1.0
\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 0.1.1
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=3D0
map[10]: type 3, range 32, base e0000000, size 27, enabled
found-> vendor=3D0x8086, dev=3D0x3340, revid=3D0x03
bus=3D0, slot=3D0, func=3D0
class=3D06-00-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0106, statreg=3D0x2090, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
found-> vendor=3D0x8086, dev=3D0x3341, revid=3D0x03
bus=3D0, slot=3D1, func=3D0
class=3D06-04-00, hdrtype=3D0x01, mfdev=3D0
cmdreg=3D0x0107, statreg=3D0x00a0, cachelnsz=3D0 (dwords)
lattimer=3D0x20 (960 ns), mingnt=3D0x0c (3000 ns), maxlat=3D0x00 (0 ns)
map[20]: type 4, range 32, base 0000bf80, size 5, enabled
pcib0: matched entry for 0.29.INTA (source \_SB_.PCI0.LNKA)
pcib0: slot 29 INTA is routed to irq 11
found-> vendor=3D0x8086, dev=3D0x24c2, revid=3D0x01
bus=3D0, slot=3D29, func=3D0
class=3D0c-03-00, hdrtype=3D0x00, mfdev=3D1
cmdreg=3D0x0005, statreg=3D0x0280, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
intpin=3Da, irq=3D11
map[20]: type 4, range 32, base 0000bf40, size 5, enabled
pcib0: matched entry for 0.29.INTB (source \_SB_.PCI0.LNKD)
pcib0: slot 29 INTB is routed to irq 11
found-> vendor=3D0x8086, dev=3D0x24c4, revid=3D0x01
bus=3D0, slot=3D29, func=3D1
class=3D0c-03-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0005, statreg=3D0x0280, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
intpin=3Db, irq=3D11
map[20]: type 4, range 32, base 0000bf20, size 5, enabled
pcib0: matched entry for 0.29.INTC (source \_SB_.PCI0.LNKC)
pcib0: slot 29 INTC is routed to irq 11
found-> vendor=3D0x8086, dev=3D0x24c7, revid=3D0x01
bus=3D0, slot=3D29, func=3D2
class=3D0c-03-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0005, statreg=3D0x0280, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
intpin=3Dc, irq=3D11
map[10]: type 1, range 32, base f4fffc00, size 10, enabled
pcib0: matched entry for 0.29.INTD (source \_SB_.PCI0.LNKH)
pcib0: slot 29 INTD is routed to irq 11
found-> vendor=3D0x8086, dev=3D0x24cd, revid=3D0x01
bus=3D0, slot=3D29, func=3D7
class=3D0c-03-20, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0106, statreg=3D0x0290, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
intpin=3Dd, irq=3D11
powerspec 2 supports D0 D3 current D0
found-> vendor=3D0x8086, dev=3D0x2448, revid=3D0x81
bus=3D0, slot=3D30, func=3D0
class=3D06-04-00, hdrtype=3D0x01, mfdev=3D0
cmdreg=3D0x0107, statreg=3D0x8080, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x04 (1000 ns), maxlat=3D0x00 (0 ns)
found-> vendor=3D0x8086, dev=3D0x24cc, revid=3D0x01
bus=3D0, slot=3D31, func=3D0
class=3D06-01-00, hdrtype=3D0x00, mfdev=3D1
cmdreg=3D0x010f, statreg=3D0x0280, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
map[10]: type 4, range 32, base 000001f0, size 3, enabled
map[14]: type 4, range 32, base 000003f4, size 2, enabled
map[18]: type 4, range 32, base 00000170, size 3, enabled
map[1c]: type 4, range 32, base 00000374, size 2, enabled
map[20]: type 4, range 32, base 0000bfa0, size 4, enabled
found-> vendor=3D0x8086, dev=3D0x24ca, revid=3D0x01
bus=3D0, slot=3D31, func=3D1
class=3D01-01-8a, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0005, statreg=3D0x0280, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
intpin=3Da, irq=3D255
map[10]: type 4, range 32, base 0000b800, size 8, enabled
map[14]: type 4, range 32, base 0000bc40, size 6, enabled
map[18]: type 1, range 32, base f4fff800, size 9, enabled
map[1c]: type 1, range 32, base f4fff400, size 8, enabled
pcib0: matched entry for 0.31.INTB (source \_SB_.PCI0.LNKB)
pcib0: slot 31 INTB is routed to irq 11
found-> vendor=3D0x8086, dev=3D0x24c5, revid=3D0x01
bus=3D0, slot=3D31, func=3D5
class=3D04-01-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0007, statreg=3D0x0290, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
intpin=3Db, irq=3D11
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000b400, size 8, enabled
map[14]: type 4, range 32, base 0000b080, size 7, enabled
pcib0: matched entry for 0.31.INTB (source \_SB_.PCI0.LNKB)
pcib0: slot 31 INTB is routed to irq 11
found-> vendor=3D0x8086, dev=3D0x24c6, revid=3D0x01
bus=3D0, slot=3D31, func=3D6
class=3D07-03-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0005, statreg=3D0x0290, cachelnsz=3D0 (dwords)
lattimer=3D0x00 (0 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
intpin=3Db, irq=3D11
powerspec 2 supports D0 D3 current D0
agp0: <Intel 82855 host to AGP bridge> mem 0xe0000000-0xe7ffffff at device =
0.0 on pci0
agp0: allocating GATT for aperture of size 128M
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xc000-0xcfff
pcib1: memory decode 0xfc000000-0xfdffffff
pcib1: prefetched decode 0xe8000000-0xefffffff
---- initial configuration ------------------------
\_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 1.0.0
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 1.0.0
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=3D1
map[10]: type 3, range 32, base e8000000, size 27, enabled
map[14]: type 4, range 32, base 0000c000, size 8, enabled
map[18]: type 1, range 32, base fcff0000, size 16, enabled
pcib1: matched entry for 1.0.INTA (source \_SB_.PCI0.LNKA)
pcib1: slot 0 INTA is routed to irq 11
found-> vendor=3D0x1002, dev=3D0x4c66, revid=3D0x01
bus=3D1, slot=3D0, func=3D0
class=3D03-00-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x01a7, statreg=3D0x02b0, cachelnsz=3D8 (dwords)
lattimer=3D0x20 (960 ns), mingnt=3D0x08 (2000 ns), maxlat=3D0x00 (0 ns)
intpin=3Da, irq=3D11
powerspec 2 supports D0 D1 D2 D3 current D0
pci1: <display, VGA> at device 0.0 (no driver attached)
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xbf80-0xbf9f irq 1=
1 at device 29.0 on pci0
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ugen0: vendor 0x413c product 0x8000, rev 1.10/5.65, addr 2
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xbf40-0xbf5f irq 1=
1 at device 29.1 on pci0
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xbf20-0xbf3f irq 1=
1 at device 29.2 on pci0
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0xd000-0xefff
pcib2: memory decode 0xf6000000-0xfbffffff
pcib2: prefetched decode 0xfff00000-0xfffff
---- initial configuration ------------------------
\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 2.1.0
\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 2.1.1
\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 2.3.0
\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 2.3.1
\_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 2.0.0
\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 2.8.0
\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 2.8.1
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 2.1.0
\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 2.1.1
\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 2.3.0
\_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 2.3.1
\_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 2.0.0
\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 2.8.0
\_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 2.8.1
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=3D2
map[10]: type 1, range 64, base faff0000, size 16, enabled
pcib2: matched entry for 2.0.INTA (source \_SB_.PCI0.LNKC)
pcib2: slot 0 INTA is routed to irq 11
found-> vendor=3D0x14e4, dev=3D0x16a6, revid=3D0x02
bus=3D2, slot=3D0, func=3D0
class=3D02-00-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0116, statreg=3D0x02b0, cachelnsz=3D8 (dwords)
lattimer=3D0x20 (960 ns), mingnt=3D0x40 (16000 ns), maxlat=3D0x00 (0 ns)
intpin=3Da, irq=3D11
powerspec 2 supports D0 D3 current D0
MSI supports 8 messages, 64 bit
found-> vendor=3D0x1217, dev=3D0x7113, revid=3D0x20
bus=3D2, slot=3D1, func=3D0
class=3D06-07-00, hdrtype=3D0x02, mfdev=3D1
cmdreg=3D0x0000, statreg=3D0x0410, cachelnsz=3D0 (dwords)
lattimer=3D0x20 (960 ns), mingnt=3D0x40 (16000 ns), maxlat=3D0x00 (0 ns)
intpin=3Da, irq=3D255
powerspec 2 supports D0 D1 D2 D3 current D0
found-> vendor=3D0x1217, dev=3D0x7113, revid=3D0x20
bus=3D2, slot=3D1, func=3D1
class=3D06-07-00, hdrtype=3D0x02, mfdev=3D1
cmdreg=3D0x0000, statreg=3D0x0410, cachelnsz=3D0 (dwords)
lattimer=3D0x20 (960 ns), mingnt=3D0x40 (16000 ns), maxlat=3D0x00 (0 ns)
intpin=3Da, irq=3D255
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base fafee000, size 13, enabled
pcib2: matched entry for 2.3.INTA (source \_SB_.PCI0.LNKB)
pcib2: slot 3 INTA is routed to irq 11
found-> vendor=3D0x14e4, dev=3D0x4320, revid=3D0x02
bus=3D2, slot=3D3, func=3D0
class=3D02-80-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0106, statreg=3D0x0010, cachelnsz=3D0 (dwords)
lattimer=3D0x20 (960 ns), mingnt=3D0x00 (0 ns), maxlat=3D0x00 (0 ns)
intpin=3Da, irq=3D11
powerspec 2 supports D0 D1 D2 D3 current D0
bge0: <Broadcom BCM5702 Gigabit Ethernet, ASIC rev. 0x1002> mem 0xfaff0000-=
0xfaffffff irq 11 at device 0.0 on pci2
pcib2: device bge0 requested decoded memory range 0xfaff0000-0xfaffffff
bge0: Ethernet address: 00:0b:db:df:53:b1
miibus0: <MII bus> on bge0
brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000b=
aseTX-FDX, auto
bge0: bpf attached
cbb0: <PCI-CardBus Bridge> at device 1.0 on pci2
pcib2: device cbb0 requested decoded memory range 0xf6000000-0xfbffffff
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib2: matched entry for 2.1.INTA (source \_SB_.PCI0.LNKD)
pcib2: slot 1 INTA is routed to irq 11
cbb0: [MPSAFE]
cbb0: PCI Configuration space:
0x00: 0x71131217 0x04100007 0x06070020 0x00822000=20
0x10: 0xf6000000 0x020000a0 0x20000000 0xfffff000=20
0x20: 0x00000000 0xfffff000 0x00000000 0x0000fffd=20
0x30: 0x00000001 0x0000fffd 0x00000001 0x0440010b=20
0x40: 0x011d1028 0x00000001 0x00000000 0x00000000=20
0x50: 0x00000000 0x00000000 0x00000000 0x00000000=20
0x60: 0x00000000 0x00000000 0x00000000 0x00000000=20
0x70: 0x00000000 0x00000000 0x00000000 0x00000000=20
0x80: 0x00000000 0x00000000 0x00000000 0x018c1882=20
0x90: 0x00350003 0x00000000 0x00000000 0x00000000=20
0xa0: 0xfe020001 0x00c04000 0x00000000 0x0000000d=20
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000=20
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000=20
0xd0: 0x08004000 0x80820bea 0x00000000 0x00400000=20
0xe0: 0x00828000 0x00000000 0x00000000 0x00000000=20
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000=20
cbb1: <PCI-CardBus Bridge> at device 1.1 on pci2
pcib2: device cbb1 requested decoded memory range 0xf6000000-0xfbffffff
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib2: matched entry for 2.1.INTA (source \_SB_.PCI0.LNKD)
pcib2: slot 1 INTA is routed to irq 11
cbb1: [MPSAFE]
cbb1: PCI Configuration space:
0x00: 0x71131217 0x04100007 0x06070020 0x00822000=20
0x10: 0xf6001000 0x020000a0 0x20000000 0xfffff000=20
0x20: 0x00000000 0xfffff000 0x00000000 0x0000fffd=20
0x30: 0x00000001 0x0000fffd 0x00000001 0x0440010b=20
0x40: 0x011d1028 0x00000001 0x00000000 0x00000000=20
0x50: 0x00000000 0x00000000 0x00000000 0x00000000=20
0x60: 0x00000000 0x00000000 0x00000000 0x00000000=20
0x70: 0x00000000 0x00000000 0x00000000 0x00000000=20
0x80: 0x00000000 0x00000000 0x00000000 0x018c1882=20
0x90: 0x00350003 0x00000000 0x00000000 0x00000000=20
0xa0: 0xfe020001 0x00c04000 0x00000000 0x0000000d=20
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000=20
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000=20
0xd0: 0x08004000 0x80800bea 0x00000000 0x04400000=20
0xe0: 0x00828000 0x00000000 0x00000000 0x00000000=20
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000=20
pci2: <network> at device 3.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port 0xbfa0-0xbfaf,0x374-0x377,0x1=
70-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 31.1 on pci0
ata0: reset tp1 mask=3D03 ostat0=3D50 ostat1=3D00
ata0-master: stat=3D0x50 err=3D0x01 lsb=3D0x00 msb=3D0x00
ata0-slave: stat=3D0x00 err=3D0x01 lsb=3D0x00 msb=3D0x00
ata0: reset tp2 mask=3D03 stat0=3D50 stat1=3D00 devices=3D0x1<ATA_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: reset tp1 mask=3D03 ostat0=3D50 ostat1=3D00
ata1-master: stat=3D0x10 err=3D0x01 lsb=3D0x14 msb=3D0xeb
ata1-slave: stat=3D0x00 err=3D0x01 lsb=3D0x00 msb=3D0x00
ata1: reset tp2 mask=3D03 stat0=3D10 stat1=3D00 devices=3D0x4<ATAPI_MASTER>
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms> at device 31.6 (no driver attached)
psmcpnp0 irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 00 00 64
psm: status 00 03 64
psm: status 00 03 64
psm: data 08 00 00
psm: status 22 02 14
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
ex_isa_identify()
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
fdc0 failed to probe at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lp0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x1 0x1 0x1 0x1
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
vga0: vga: WARNING: video mode switching is not fully supported on this ada=
pter
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 69 4f 4f 8d 55 83=20
9e 1f 00 4f 0d 0e 00 00 07 80 8f 82 8f 28 1f 8f=20
9f a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c=20
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81=20
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96=20
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c=20
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 67 69 4f 4f 8d 55 83=20
9e 1f 00 4f 0d 0e 00 00 07 80 8f 82 8f 28 1f 8f=20
9f a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c=20
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff=20
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 1395477939 Hz quality 800
Timecounters tick every 10.000 msec
lo0: bpf attached
malloc() of "16" with the following non-sleepable locks held:
exclusive sleep mutex ifnet r =3D 0 (0xc0924e20) locked @ /usr/src/sys/net/=
if.c:459
malloc() of "256" with the following non-sleepable locks held:
exclusive sleep mutex ifnet r =3D 0 (0xc0924e20) locked @ /usr/src/sys/net/=
if.c:459
malloc() of "512" with the following non-sleepable locks held:
exclusive sleep mutex ifnet r =3D 0 (0xc0924e20) locked @ /usr/src/sys/net/=
if.c:459
malloc() of "64" with the following non-sleepable locks held:
exclusive sleep mutex ifnet r =3D 0 (0xc0924e20) locked @ /usr/src/sys/net/=
if.c:459
malloc() of "64" with the following non-sleepable locks held:
exclusive sleep mutex ifnet r =3D 0 (0xc0924e20) locked @ /usr/src/sys/neti=
net6/in6.c:2295
malloc() of "16" with the following non-sleepable locks held:
exclusive sleep mutex ifnet r =3D 0 (0xc0924e20) locked @ /usr/src/sys/neti=
net6/in6.c:2295
malloc() of "256" with the following non-sleepable locks held:
exclusive sleep mutex ifnet r =3D 0 (0xc0924e20) locked @ /usr/src/sys/neti=
net6/in6.c:2295
malloc() of "512" with the following non-sleepable locks held:
exclusive sleep mutex ifnet r =3D 0 (0xc0924e20) locked @ /usr/src/sys/neti=
net6/in6.c:2295
malloc() of "64" with the following non-sleepable locks held:
exclusive sleep mutex ifnet r =3D 0 (0xc0924e20) locked @ /usr/src/sys/neti=
net6/in6.c:2295
malloc() of "64" with the following non-sleepable locks held:
exclusive sleep mutex ifnet r =3D 0 (0xc0924e20) locked @ /usr/src/sys/neti=
net6/in6.c:2295
malloc() of "16" with the following non-sleepable locks held:
exclusive sleep mutex ifnet r =3D 0 (0xc0924e20) locked @ /usr/src/sys/neti=
net6/in6.c:2295
malloc() of "256" with the following non-sleepable locks held:
exclusive sleep mutex ifnet r =3D 0 (0xc0924e20) locked @ /usr/src/sys/neti=
net6/in6.c:2295
malloc() of "512" with the following non-sleepable locks held:
exclusive sleep mutex ifnet r =3D 0 (0xc0924e20) locked @ /usr/src/sys/neti=
net6/in6.c:2295
malloc() of "64" with the following non-sleepable locks held:
exclusive sleep mutex ifnet r =3D 0 (0xc0924e20) locked @ /usr/src/sys/neti=
net6/in6.c:2295
malloc() of "64" with the following non-sleepable locks held:
exclusive sleep mutex ifnet r =3D 0 (0xc0924e20) locked @ /usr/src/sys/neti=
net6/in6.c:2295
ata1: spurious interrupt - status=3D0x00 error=3D0x01
acpi_cpu0: set speed to 100.0%
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
acpi_acad0: acline initialization start
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
acpi_cmbat0: battery initialization start
acpi_cmbat1: battery initialization start
cardbus0: Resource not specified in CIS: id=3D10, size=3D10000
pcib2: device cardbus0 requested decoded memory range 0xf6000000-0xfbffffff
found-> vendor=3D0x14e4, dev=3D0x16a6, revid=3D0x02
bus=3D2, slot=3D0, func=3D0
class=3D02-00-00, hdrtype=3D0x00, mfdev=3D0
cmdreg=3D0x0106, statreg=3D0x02b0, cachelnsz=3D8 (dwords)
lattimer=3D0xa8 (5040 ns), mingnt=3D0x40 (16000 ns), maxlat=3D0x00 (0 ns)
intpin=3Da, irq=3D222
powerspec 2 supports D0 D3 current D0
MSI supports 8 messages, 64 bit
cardbus0: <network, ethernet> at device 0.0 (no driver attached)
cbb0: CardBus card activation failed
pcib2: device pccard1 requested decoded memory range 0xf6000000-0xfbffffff
pccard1: CIS version PC Card Standard 7.0
pccard1: CIS info: O2Micro, SmartCardBus Reader, V1.0
pccard1: Manufacturer code 0xffff, product 0x1
pccard1: function 0: unspecified, ccr addr 220 mask 1
pccard1: function 0, config table entry 1: I/O card; irq mask beb8; iomask =
5, iospace 0-1f; memspace 0-ff; io16 irqlevel
pcib2: device pccard1 requested decoded I/O range 0x100-0xffffffff
pcib2: device pccard1 requested decoded memory range 0xf6000000-0xfbffffff
pccard1: <unknown card> (manufacturer=3D0xffff, product=3D0x0001) at functi=
on 0
pccard1: CIS info: O2Micro, SmartCardBus Reader, V1.0
ata0-master: pio=3D0x0c wdma=3D0x22 udma=3D0x45 cable=3D80pin
ad0: setting UDMA100 on Intel ICH4 chip
GEOM: create disk ad0 dp=3D0xc4852d70
ad0: <IC25N040ATCS05-0/CS4OA63A> ATA-5 disk at ata0-master
ad0: 38154MB (78140160 sectors), 77520 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
GEOM: new disk ad0
ar: FreeBSD check1 failed
[0] f:00 typ:222 s(CHS):0/1/1 e(CHS):5/254/63 s:63 l:96327
[1] f:00 typ:7 s(CHS):6/0/1 e(CHS):1023/254/63 s:96390 l:20482875
[2] f:00 typ:15 s(CHS):1023/255/63 e(CHS):1023/254/63 s:20579265 l:20482875
[3] f:80 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:41062140 l:20964825
GEOM: Configure ad0s1, start 32256 length 49319424 end 49351679
GEOM: Configure ad0s2, start 49351680 length 10487232000 end 10536583679
GEOM: Configure ad0s3, start 10536583680 length 10487232000 end 21023815679
GEOM: Configure ad0s4, start 21023815680 length 10733990400 end 31757806079
ata1-master: pio=3D0x0c wdma=3D0x22 udma=3D0x42 cable=3D40pin
acd0: setting PIO4 on Intel ICH4 chip
acd0: <QSI CD-RW/DVD-ROM SBW-242/UD22> CDRW drive at ata1 as master
acd0: read 4126KB/s (4126KB/s) write 4126KB/s (4126KB/s), 2048KB buffer, PI=
O4
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet
acd0: Writes: CDR, CDRW, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-R 120mm data disc
MBREXT Slice 5 on ad0s3:
[0] f:00 typ:11 s(CHS):1023/1/1 e(CHS):1023/254/63 s:63 l:2040192
[1] f:00 typ:5 s(CHS):1023/0/1 e(CHS):1023/254/63 s:2040255 l:18442620
GEOM: Configure ad0s5, start 32256 length 1044578304 end 1044610559
MBREXT Slice 6 on ad0s3:
[0] f:00 typ:11 s(CHS):1023/1/1 e(CHS):1023/254/63 s:63 l:18442557
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s6, start 1044642816 length 9442589184 end 10487231999
GEOM: Configure ad0s4a, start 0 length 536870912 end 536870911
GEOM: Configure ad0s4b, start 536870912 length 1073741824 end 1610612735
GEOM: Configure ad0s4c, start 0 length 10733990400 end 10733990399
GEOM: Configure ad0s4d, start 1610612736 length 1073741824 end 2684354559
GEOM: Configure ad0s4e, start 2684354560 length 8049635840 end 10733990399
Mounting root from ufs:/dev/ad0s4a
start_init: trying /sbin/init
Loading configuration files.
Entropy harvesting: interrupts ethernet point_to_point.
swapon: adding /dev/ad0s4b as swap device
Starting file system checks:
/dev/ad0s4a: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s4a: clean, 208221 free (1141 frags, 25885 blocks, 0.4% fragmentati=
on)
/dev/ad0s4e: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s4e: clean, 3578286 free (2174 frags, 447014 blocks, 0.1% fragmenta=
tion)
/dev/ad0s4d: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s4d: clean, 506413 free (21 frags, 63299 blocks, 0.0% fragmentation)
Setting hostname: aklemm.klemm.apsfilter.org.
lo0: flags=3D8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000=20
inet6 ::1 prefixlen 128=20
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3=20
Starting dhclient.
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: RX CPU self-diagnostics failed!
bge0: flow-through queue init failed
bge0: initialization failure
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: RX CPU self-diagnostics failed!
bge0: flow-through queue init failed
bge0: initialization failure
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: RX CPU self-diagnostics failed!
bge0: flow-through queue init failed
bge0: initialization failure
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: flags=3D8803<UP,BROADCAST,SIMPLEX,MULTICAST> mtu 1500
options=3D1b<RXCSbUM,TXCSUM,VLAN_MgTU,VLAN_HWTAGGINeG>
0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
inet6 fe80::20b:dbff:fedf:53b1%bge0 prefixlen 64 scopeid 0x1=20
inet 0.0.0.0 nebtmask 0xff000000g broadcast 255.2e55.255.255
eth0er 00:0b:db:df:5:3:b1
PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
media: Ethernet autoselect
status: no carrier
Additional routing options:.
hw.bus.devctl_disable: 0 -> 1
Mounting NFS file systems:.
Starting syslogd.
Oct 25 13:52:29 aklemm syslogd: kernel boot file is /boot/kernel/kernel
ELF ldconfig path: /lib /usr/lib /usr/lib/compat
a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout
Starting usbd.
Starting local daemons:.
Updating motd.
Configuring syscons: keymap keyrate font8x16 font8x14 font8x8 blanktime scr=
eensaver.
Starting sshd.
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
Initial i386 initialization:.
Additional ABI support:.
Starting cron.
Local package initialization:.
Additional TCP options:.
Starting moused:.
Starting background file system checks in 60 seconds.
Sat Oct 25 13:52:33 CEST 2003
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
-0166: *** Error: UtAllocate: Attempt to allocate zero bytes
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
acpi_cmbat0: battery initialization failed, giving up
acpi_cmbat1: battery initialization failed, giving up
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
V&Y read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
FreeBSD/i386 (aklemm.klemm.apsfilter.org) (ttyd0)
login: rbge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
oot
Password:
Oct 25 13:53:47 aklemm login: ROOT LOGIN (root) ON ttyd0
Last login: Sat Oct 25 13:53:12 on ttyv0
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.1-20031024-SNAP (GENERIC) #0: Sat Oct 25 03:04:22 GMT 2003
Welcome to FreeBSD!
Before seeking technical support, please use the following resources:
o Security advisories and updated errata information for all releases are
at http://www.FreeBSD.org/releases/ - always consult the ERRATA section
for your release first as it's updated frequently.
o The Handbook and FAQ documents are at http://www.FreeBSD.org/ and,
along with the mailing lists, can be searched by going to
http://www.FreeBSD.org/search/. If the doc distribution has
been installed, they're also available formatted in /usr/share/doc.
If you still have a question or problem, please take the output of
`uname -a', along with any relevant error messages, and email it
as a question to the questions@FreeBSD.org mailing list. If you are
unfamiliar with FreeBSD's directory layout, please refer to the hier(7)
manual page. If you are not familiar with manual pages, type `man man'.
You may also use sysinstall(8) to re-enter the installation and
configuration utility. Edit /etc/motd to change this login announcement.
aklemm# bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
ps -ax
PID TT STAT TIME COMMAND
0 ?? DLs 0:00.00 (swapper)
1 ?? SLs 0:00.11 /sbin/init --
2 ?? DL 0:00.87 (g_event)
3 ?? DL 0:00.05 (g_up)
4 ?? DL 0:00.09 (g_down)
5 ?? DL 0:00.00 (taskqueue)
6 ?? IL 0:00.00 (acpi_task0)
7 ?? IL 0:02.18 (acpi_task1)
8 ?? IL 0:00.06 (acpi_task2)
9 ?? DL 0:00.00 (cbb0)
10 ?? DL 0:00.00 (ktrace)
11 ?? RL 1:26.64 (idle)
12 ?? WL 0:00.01 (swi1: net)
13 ?? WL 0:00.08 (swi8: tty:sio clock)
15 ?? DL 0:00.01 (random)
17 ?? WL 0:00.00 (swi7: acpitaskq)
21 ?? WL 0:00.03 (swi7: task queue)
23 ?? WL 0:00.00 (irq9: acpi0)
24 ?? DL 0:00.02 (acpi_thermal)
25 ?? WL 0:00.00 (irq11: cbb0 cbb1++*)
26 ?? DL 0:00.00 (usb0)
27 ?? DL 0:00.00 (usbtask)
28 ?? DL 0:00.00 (usb1)
29 ?? DL 0:00.00 (usb2)
30 ?? DL 0:00.00 (cbb1)
31 ?? WL 0:00.02 (irq14: ata0)
32 ?? WL 0:00.00 (irq15: ata1)
33 ?? WL 0:00.01 (irq1: atkbd0)
35 ?? WL 0:00.00 (irq7: ppc0)
36 ?? WL 0:00.00 (swi0: tty:sio)
40 ?? DL 0:00.00 (pagedaemon)
41 ?? DL 0:00.00 (vmdaemon)
42 ?? DL 0:00.46 (pagezero)
43 ?? DL 0:00.00 (bufdaemon)
44 ?? DL 0:00.00 (vnlru)
45 ?? DL 0:00.01 (syncer)
46 ?? IL 0:00.00 (nfsiod 0)
47 ?? IL 0:00.00 (nfsiod 1)
48 ?? IL 0:00.00 (nfsiod 2)
49 ?? IL 0:00.00 (nfsiod 3)
146 ?? Is 0:00.00 adjkerntz -i
185 ?? Ss 0:05.18 /sbin/dhclient bge0
241 ?? Ss 0:00.09 /usr/sbin/syslogd -s
337 ?? Ss 0:00.00 /usr/sbin/usbd
395 ?? Is 0:00.08 /usr/sbin/sshd
401 ?? Ss 0:00.01 sendmail: accepting connections (sendmail)
404 ?? Is 0:00.00 sendmail: Queue runner@00:30:00 for /var/spool/cl=
ient
418 ?? Is 0:00.01 /usr/sbin/cron
442 ?? Is 0:00.00 /usr/sbin/moused -p /dev/psm0 -t auto
470 v0 Is 0:00.12 login [pam] (login)
478 v0 S+ 0:00.03 -csh (csh)
471 v1 Is+ 0:00.01 /usr/libexec/getty Pc ttyv1
472 v2 Is+ 0:00.01 /usr/libexec/getty Pc ttyv2
473 v3 Is+ 0:00.01 /usr/libexec/getty Pc ttyv3
474 v4 Is+ 0:00.01 /usr/libexec/getty Pc ttyv4
475 v5 Is+ 0:00.01 /usr/libexec/getty Pc ttyv5
476 v6 Is+ 0:00.01 /usr/libexec/getty Pc ttyv6
477 v7 Is+ 0:00.01 /usr/libexec/getty Pc ttyv7
484 d0 Ss 0:00.12 login [pam] (login)
485 d0 S 0:00.03 -csh (csh)
487 d0 R+ 0:00.00 ps -ax
aklemm# bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
unam e=08 =08=08e -bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
a
FreeBSD aklemm.klemm.apsfilter.org 5.1-20031024-SNAP FreeBSD 5.1-20031024-S=
NAP #0: Sat Oct 25 03:04:22 GMT 2003 root@titan.klemm.apsfilter.org:/us=
r/obj/usr/src/sys/GENERIC i386
aklemm#=20
aklemm# uname -a
FreeBSD aklemm.klemm.apsfilter.org 5.1-20031024-SNAP FreeBSD 5.1-20031024-S=
NAP #0: Sat Oct 25 03:04:22 GMT 2003 root@titan.klemm.apsfilter.org:/us=
r/obj/usr/src/sys/GENERIC i386
aklemm# bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
aklemm# pbge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
cc=07ardd -dbge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
aklemm# Oct 25 13:54:25 aklemm pccardd[490]: fatal error: no PC-CARD slots
aklemm# bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
aklemm#=20
aklemm# pccardd -d
aklemm# Oct 25 13:54:32 aklemm pccardd[491]: fatal error: no PC-CARD slots
aklemm#=20
aklemm#=20
aklemm# bge0: PHY read timed out
bge0: PHY read timed out
bge0: PHY read timed out
aklemm#=20
Andreas ///
--=20
Andreas Klemm - Powered by FreeBSD 5.1-CURRENT
Need a magic printfilter today ? -> http://www.apsfilter.org/
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20031025121215.GA70499>