Date: Sun, 2 Jan 2000 22:35:26 +0100 (CET) From: Dirk-Willem van Gulik <dirkx@webweaving.org> To: freebsd-mobile@freebsd.org Subject: Sony Memory stick Message-ID: <Pine.BSF.4.10.10001022234120.673-100000@mobile.webweaving.org>
next in thread | raw e-mail | index | archive | help
As promised, Just to inform you that the sony memory stick's, with
their normal SONY PCMCIA adaptor work just fine under freebsd.
Attached is the dump.
Simply
mount -t msdos /dev/wd0s1 /mnt
And one is there. Version used is PAO3 on FreeBSD 3.2-RELEASE.
The adaptor I used is the one described in detail on Sony's web
site 'Aibo'->'Performance kit'. And is identical in labeling
and numbering (though not in colour) to the device's you can
buy in europe with the camera's.
Dw.
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 4
000: df 4a 01 ff
Common memory device information:
Device number 1, type Function specific, WPS = ON
Speed = 4.0 x 100 ns, Memory block size = reserved, 32 units
Device number 2, type No device, WPS = OFF
Speed = No speed, Memory block size = 512b, 1 units
Tuple #2, code = 0x1c (Other conditions for common memory), length = 4
000: 02 d9 01 ff
(3V card)
Tuple #3, code = 0x18 (JEDEC descr for common memory), length = 2
000: df 01
Tuple #4, code = 0x20 (Manufacturer ID), length = 4
000: f1 00 00 00
PCMCIA ID = 0xf1, OEM ID = 0x0
Tuple #5, code = 0x15 (Version 1 info), length = 30
000: 04 01 53 4f 4e 59 00 4d 45 4d 4f 52 59 53 54 49
010: 43 4b 28 20 20 38 4d 29 00 31 2e 30 00 ff
Version = 4.1, Manuf = [SONY], card vers = [MEMORYSTICK( 8M)]
Addit. info = [1.0]
Tuple #6, code = 0x21 (Functional ID), length = 2
000: 04 01
Fixed disk card - POST initialize
Tuple #7, code = 0x22 (Functional EXT), length = 2
000: 01 01
Disk interface: IDE
Tuple #8, code = 0x22 (Functional EXT), length = 3
000: 02 0c 0f
Disk features: Silicon, Unique, Single
Sleep, Standby, Idle, Low power,
Tuple #9, code = 0x1a (Configuration map), length = 5
000: 01 03 00 02 0f
Reg len = 2, config register addr = 0x200, last config = 0x3
Registers: XXXX----
Tuple #10, code = 0x1b (Configuration entry), length = 8
000: c0 c0 a1 01 55 08 00 20
Config index = 0x0(default)
Interface byte = 0xc0 (memory) +RDY/-BSY active, wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Memory space length = 0x8
Max twin cards = 0
Misc attr: (Power down supported)
Tuple #11, code = 0x1b (Configuration entry), length = 6
000: 00 01 21 b5 1e 0e
Config index = 0x0
Vcc pwr:
Nominal operating supply voltage: 3 x 1V, ext = 0x1e
Max current average over 10 ms: 1.2 x 100mA
Tuple #12, code = 0x1b (Configuration entry), length = 10
000: c1 41 99 01 55 64 f0 ff ff 20
Config index = 0x1(default)
Interface byte = 0x41 (I/O) +RDY/-BSY active
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Card decodes 4 address lines, full 8/16 Bit I/O
IRQ modes: Level, Pulse, Shared
IRQs: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Max twin cards = 0
Misc attr: (Power down supported)
Tuple #13, code = 0x1b (Configuration entry), length = 6
000: 01 01 21 b5 1e 4d
Config index = 0x1
Vcc pwr:
Nominal operating supply voltage: 3 x 1V, ext = 0x1e
Max current average over 10 ms: 4.5 x 10mA
Tuple #14, code = 0x1b (Configuration entry), length = 15
000: c2 41 99 01 55 ea 61 f0 01 07 f6 03 01 ee 20
Config index = 0x2(default)
Interface byte = 0x41 (I/O) +RDY/-BSY active
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Card decodes 10 address lines, full 8/16 Bit I/O
I/O address # 1: block start = 0x1f0 block length = 0x8
I/O address # 2: block start = 0x3f6 block length = 0x2
IRQ modes: Level, Pulse, Shared
IRQ level = 14
Max twin cards = 0
Misc attr: (Power down supported)
Tuple #15, code = 0x1b (Configuration entry), length = 6
000: 02 01 21 b5 1e 4d
Config index = 0x2
Vcc pwr:
Nominal operating supply voltage: 3 x 1V, ext = 0x1e
Max current average over 10 ms: 4.5 x 10mA
Tuple #16, code = 0x1b (Configuration entry), length = 15
000: c3 41 99 01 55 ea 61 70 01 07 76 03 01 ee 20
Config index = 0x3(default)
Interface byte = 0x41 (I/O) +RDY/-BSY active
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Card decodes 10 address lines, full 8/16 Bit I/O
I/O address # 1: block start = 0x170 block length = 0x8
I/O address # 2: block start = 0x376 block length = 0x2
IRQ modes: Level, Pulse, Shared
IRQ level = 14
Max twin cards = 0
Misc attr: (Power down supported)
Tuple #17, code = 0x1b (Configuration entry), length = 6
000: 03 01 21 b5 1e 4d
Config index = 0x3
Vcc pwr:
Nominal operating supply voltage: 3 x 1V, ext = 0x1e
Max current average over 10 ms: 4.5 x 10mA
Tuple #18, code = 0x14 (No link), length = 0
Tuple #19, code = 0xff (Terminator), length = 0
1 slots found
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.4.10.10001022234120.673-100000>