Date: Wed, 3 Dec 2014 17:16:22 +0000 (UTC) From: Benedict Reuschling <bcr@FreeBSD.org> To: doc-committers@freebsd.org, svn-doc-all@freebsd.org, svn-doc-head@freebsd.org Subject: svn commit: r46058 - in head/en_US.ISO8859-1/books/handbook: firewalls ppp-and-slip x11 Message-ID: <201412031716.sB3HGMcs001883@svn.freebsd.org>
next in thread | raw e-mail | index | archive | help
Author: bcr Date: Wed Dec 3 17:16:21 2014 New Revision: 46058 URL: https://svnweb.freebsd.org/changeset/doc/46058 Log: Add two spaces at the start of a sentence where needed. This is a whitespace change that translators can ignore. Obtained from: igor -n invocation Modified: head/en_US.ISO8859-1/books/handbook/firewalls/chapter.xml head/en_US.ISO8859-1/books/handbook/ppp-and-slip/chapter.xml head/en_US.ISO8859-1/books/handbook/x11/chapter.xml Modified: head/en_US.ISO8859-1/books/handbook/firewalls/chapter.xml ============================================================================== --- head/en_US.ISO8859-1/books/handbook/firewalls/chapter.xml Wed Dec 3 17:07:07 2014 (r46057) +++ head/en_US.ISO8859-1/books/handbook/firewalls/chapter.xml Wed Dec 3 17:16:21 2014 (r46058) @@ -2313,7 +2313,7 @@ good_tcpo="22,25,37,53,80,443,110"</prog <para>On the inbound side, the ruleset has to deny bad packets and allow only authorized services. A packet which matches an inbound rule is posted to the dynamic state table and the - packet is released to the <acronym>LAN</acronym>. The packet + packet is released to the <acronym>LAN</acronym>. The packet generated as a response is recognized by the <literal>check-state</literal> rule as belonging to an existing session. It is then sent to rule Modified: head/en_US.ISO8859-1/books/handbook/ppp-and-slip/chapter.xml ============================================================================== --- head/en_US.ISO8859-1/books/handbook/ppp-and-slip/chapter.xml Wed Dec 3 17:07:07 2014 (r46057) +++ head/en_US.ISO8859-1/books/handbook/ppp-and-slip/chapter.xml Wed Dec 3 17:16:21 2014 (r46058) @@ -216,7 +216,7 @@ <para>In order to configure a <acronym>PPP</acronym> connection, first edit <filename>/etc/ppp/ppp.conf</filename> with the - dial-in information for the <acronym>ISP</acronym>. This file + dial-in information for the <acronym>ISP</acronym>. This file is described as follows:</para> <programlisting>1 default: @@ -818,7 +818,7 @@ set nbns 203.14.100.5</programlisting> <programlisting>nat enable yes</programlisting> <para>Alternatively, NAT may be enabled by command-line - option <literal>-nat</literal>. There is also + option <literal>-nat</literal>. There is also <filename>/etc/rc.conf</filename> knob named <literal>ppp_nat</literal>, which is enabled by default.</para> @@ -1511,8 +1511,8 @@ ppp_profile="adsl"</programlisting> configure <application>mpd</application> is available in HTML format in <filename>/usr/ports/share/doc/mpd/</filename>. Here is a sample configuration for connecting to an ADSL - service with <application>mpd</application>. The configuration - is spread over two files, first the + service with <application>mpd</application>. The + configuration is spread over two files, first the <filename>mpd.conf</filename>:</para> <note> @@ -1641,7 +1641,7 @@ ng0: flags=88d1<UP,POINTOPOINT,RUNNIN session to the DSL router. Ethernet DSL modems have a preconfigured LAN <acronym>IP</acronym> address to connect to. In the case of the Alcatel &speedtouch; Home, this address is - <systemitem class="ipaddress">10.0.0.138</systemitem>. The + <systemitem class="ipaddress">10.0.0.138</systemitem>. The router's documentation should list the address the device uses. To open the tunnel and start a <acronym>PPP</acronym> session:</para> Modified: head/en_US.ISO8859-1/books/handbook/x11/chapter.xml ============================================================================== --- head/en_US.ISO8859-1/books/handbook/x11/chapter.xml Wed Dec 3 17:07:07 2014 (r46057) +++ head/en_US.ISO8859-1/books/handbook/x11/chapter.xml Wed Dec 3 17:16:21 2014 (r46058) @@ -516,7 +516,7 @@ dbus_enable="YES"</programlisting> </note> <para>If the test is unsuccessful, skip ahead to <xref - linkend="x11-understanding"/>. Once the test is successful, + linkend="x11-understanding"/>. Once the test is successful, copy the configuration file to <filename>/etc/X11/xorg.conf</filename>:</para>
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?201412031716.sB3HGMcs001883>