Date: Mon, 8 Dec 2003 00:30:17 -0500 (EST) From: "Judd Storrs" <storrsjm@email.uc.edu> To: <freebsd-firewire@freebsd.org> Subject: Re: Sony DRX-510UL CD/DVD burner: probe failed for 1 node Message-ID: <49266.172.22.77.20.1070861417.squirrel@storrs.net> In-Reply-To: <87smjw57c2.wl@tora.nunu.org> References: <49736.172.22.77.20.1070818595.squirrel@storrs.net> <87smjw57c2.wl@tora.nunu.org>
next in thread | previous in thread | raw e-mail | index | archive | help
[-- Attachment #1 --]
Hidetoshi Shimokawa wrote:
> Could you send me the output of 'fwcontrol -c 0' and dmesg without aio
> module?
> What happens if you initiate a bus reset manually by 'fwcontrol -r'?
I collected results for these commands with and without aio and collected
the results into the attachment. Lines marked with "AIO" or "NOAIO" at the
beginning were different. Lines indented five spaces were the same for
both.
The bus resets didn't seem to result in any change except that sometimes
the DVD node would disappeared from 'fwcontrol'. I think this was due to
the drive "sleeping" because opening and closing the tray before issuing
another 'fwcontrol -r' always worked to list the DVD drive in 'fwcontrol'.
Thanks,
--judd
[-- Attachment #2 --]
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.2-BETA #1: Sun Dec 7 00:22:06 EST 2003
root@anubis.storrs.net:/mnt/anubis/obj/mnt/anubis/src/sys/ANUBIS
NOAIO Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a92000.
NOAIO Preloaded elf module "/boot/kernel/snd_ich.ko" at 0xc0a921cc.
NOAIO Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc0a92278.
NOAIO Preloaded acpi_dsdt "/boot/acpi_dell_dsdt.aml" at 0xc0a92324.
NOAIO Preloaded elf module "/boot/kernel/speaker.ko" at 0xc0a92374.
AIO Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a9b000.
AIO Preloaded elf module "/boot/kernel/snd_ich.ko" at 0xc0a9b1cc.
AIO Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc0a9b278.
AIO Preloaded acpi_dsdt "/boot/acpi_dell_dsdt.aml" at 0xc0a9b324.
AIO Preloaded elf module "/boot/kernel/aio.ko" at 0xc0a9b374.
AIO Preloaded elf module "/boot/kernel/speaker.ko" at 0xc0a9b41c.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) III Mobile CPU 1000MHz (996.79-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 268251136 (255 MB)
NOAIO avail memory = 250920960 (239 MB)
AIO avail memory = 250916864 (239 MB)
Pentium Pro MTRR support enabled
ACPI: DSDT was overridden.
ACPI-0375: *** Info: Table [DSDT] replaced by host OS
acpi0: <DELL CPi R > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 11 entries at 0xc00fbb90
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_acad0: <AC Adapter> on acpi0
acpi_cmbat0: <Control Method Battery> on acpi0
acpi_cmbat1: <Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib0: slot 29 INTA is routed to irq 11
pcib0: slot 31 INTB is routed to irq 11
pcib0: slot 31 INTB is routed to irq 11
agp0: <Intel 82830 host to AGP bridge> mem 0xd0000000-0xdfffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib1: slot 0 INTA is routed to irq 11
pci1: <display, VGA> at device 0.0 (no driver attached)
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0xbf80-0xbf9f irq 11 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM), rev 1.10/3.00, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib2: slot 0 INTA is routed to irq 11
pcib2: slot 3 INTA is routed to irq 11
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xec80-0xecff mem 0xf8fffc00-0xf8fffc7f irq 11 at device 0.0 on pci2
xl0: Ethernet address: 00:06:5b:31:4b:92
miibus0: <MII bus> on xl0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cbb0: <TI1420 PCI-CardBus Bridge> at device 1.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib2: slot 1 INTA is routed to irq 11
cbb0: [MPSAFE]
cbb1: <TI1420 PCI-CardBus Bridge> at device 1.1 on pci2
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
pcib2: slot 1 INTA is routed to irq 11
cbb1: [MPSAFE]
cbb2: <TI1410 PCI-CardBus Bridge> irq 11 at device 3.0 on pci2
cardbus2: <CardBus bus> on cbb2
pccard2: <16-bit PCCard bus> on cbb2
cbb2: [MPSAFE]
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 UDMA100 controller> port 0xbfa0-0xbfaf,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pcm0: <Intel ICH3 (82801CA)> port 0xdc80-0xdcbf,0xd800-0xd8ff irq 11 at device 31.5 on pci0
pcm0: <Cirrus Logic CS4205 AC97 Codec>
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
speaker0 port 0x67,0x65,0x63,0x61 on acpi0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0 port 0x270-0x277,0x3f8-0x3ff irq 4 drq 3 on acpi0
sio0: type 16550A
ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 1 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
NOAIO Timecounter "TSC" frequency 996789690 Hz quality 800
AIO Timecounter "TSC" frequency 996789780 Hz quality 800
Timecounters tick every 10.000 msec
wi0: <Dell TrueMobile 1150 Series PC Card> at port 0x100-0x13f irq 11 function 0 config 1 on pccard2
wi0: 802.11 address: 00:02:2d:81:3a:4b
wi0: using Lucent Embedded WaveLAN/IEEE
wi0: Lucent Firmware: Station (8.72.1)
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
NOAIO GEOM: create disk ad0 dp=0xc2e54760
AIO GEOM: create disk ad0 dp=0xc2e5f660
ad0: 19077MB <HITACHI_DK23CA-20> [38760/16/63] at ata0-master UDMA100
acd0: CDROM <SAMSUNG CD-ROM SN-124> at ata1-master PIO4
Mounting root from ufs:/dev/ad0s3a
##################################################
### INSERT FIREWIRE PCMCIA CARD [AIO/NO AIO SAME]
cardbus1: Resource not specified in CIS: id=10, size=800
cardbus1: Resource not specified in CIS: id=14, size=4000
fwohci0: <Texas Instruments TSB43AB23> mem 0xf4004000-0xf4007fff,0xf4008000-0xf40087ff irq 11 at device 0.0 on cardbus1
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 08:00:28:56:02:00:03:33
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 0a:00:28:00:03:33
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
cardbus1: Resource not specified in CIS: id=10, size=1000
ohci0: <NEC uPD 9210 USB controller> mem 0xf4004000-0xf4004fff irq 11 at device 0.4 on cardbus1
usb1: OHCI version 0.0
usb1: unsupported OHCI revision
ohci0: USB init failed
device_probe_and_attach: ohci0 attach returned 5
cardbus1: Resource not specified in CIS: id=10, size=1000
ohci0: <NEC uPD 9210 USB controller> mem 0xf4004000-0xf4004fff irq 11 at device 0.5 on cardbus1
usb1: OHCI version 0.0
usb1: unsupported OHCI revision
ohci0: USB init failed
device_probe_and_attach: ohci0 attach returned 5
cardbus1: Resource not specified in CIS: id=10, size=100
cardbus1: <serial bus, USB> at device 0.6 (no driver attached)
##################################################
### ATTACH DVD DRIVE
fwohci0: BUS reset
NOAIO fwohci0: node_id=0xc000ffc1, gen=3, CYCLEMASTER mode
NOAIO firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
NOAIO firewire0: bus manager 1 (me)
AIO fwohci0: node_id=0x8000ffc0, gen=3, non CYCLEMASTER mode
AIO firewire0: 2 nodes, maxhop <= 1, cable IRM = 0 (me)
AIO firewire0: root node is not cycle master capable
AIO firewire0: bus manager 0 (me)
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc1, gen=4, CYCLEMASTER mode
firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
firewire0: bus manager 1 (me)
firewire0: New S400 device ID:080046090009e518
firewire0: split transaction timeout dst=0xffc0 tl=0x4 state=3
node0: resp=60 addr=0x400
probe failed for 1 node
##################################################
### fwcontrol [AIO/NO AIO SAME]
2 devices (info_len=2)
node EUI64 status
1 0x0800285602000333 0
-1 0x080046090009e518 0
##################################################
### fwcontrol -c 0 [AIO/NO AIO SAME]
first quad: 0x00000000 info_len=0 crc_len=0 crc=0x0000(OK)
bus_name: 0x0000
irmc:0 cmc:0 isc:0 bmc:0 pmc:0
cyc_clk_acc:0 max_rec:0 max_rom:0
generation:0 link_spd:0
EUI64: 0x00000000 0x00000000
root_directory: len=0x000c(12) crc=0x7864(NG)
##################################################
### fwcontrol -c 1 [AIO/NO AIO SAME]
first quad: 0x041bd246 info_len=4 crc_len=27 crc=0xd246(OK)
bus_name: 0x31333934
irmc:1 cmc:1 isc:1 bmc:1 pmc:0
cyc_clk_acc:100 max_rec:10 max_rom:0
generation:2 link_spd:2
EUI64: 0x08002856 0x02000333
root_directory: len=0x0005(5) crc=0xc305(OK)
0c(I:0c) 0083c0 node_capabilities:
03(I:03) acde48 module_vendor_ID:
81(L:01) 000003 text_leaf: len=7 crc=0x82ed(OK) FreeBSD Project
04(I:04) 07a57a hardware_version:
81(L:01) 000009 text_leaf: len=8 crc=0x8d33(OK) anubis.storrs.net
##################################################
### fwcontrol -r [AIO/NO AIO SAME]
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc1, gen=5, CYCLEMASTER mode
firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
firewire0: bus manager 1 (me)
firewire0: split transaction timeout dst=0xffc0 tl=0x7 state=3
node0: resp=60 addr=0x410
probe failed for 1 node
##################################################
### fwcontrol [AIO/NO AIO SAME]
### fwcontrol -c 0 [AIO/NO AIO SAME]
### fwcontrol -c 1 [AIO/NO AIO SAME]
Same as above
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?49266.172.22.77.20.1070861417.squirrel>