Date: Fri, 30 Jun 2000 19:33:56 +0400 (MSD) From: undef <hideout@mail.ru> To: Mark Blackman <mark.blackman@dircon.net> Cc: multimedia@freebsd.org Subject: Re: troubles with soundcard under freebsd Message-ID: <XFMail.20000630193356.hideout@mail.ru> In-Reply-To: <20000630093618.A35761@diablo.dircon.net>
index | next in thread | previous in thread | raw e-mail
[-- Attachment #1 --] Hi, dmesg devices probe: ----------------------------------------------------- VESA: v2.0, 4096k memory, flags:0x1, mode table:0xc040a102 (1000022) VESA: Matrox Graphics Inc. Pentium Pro MTRR support enabled md0: Malloc disk module_register_init: MOD_LOAD (splash_pcx, c0403530, 0) error 2 npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard pci0: <PCI bus> on pcib0 pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 7.2 irq 11 chip1: <Intel 82371AB Power management controller> port 0x5000-0x500f at device 7.3 on pci0 pci0: <Matrox MGA 1024SG/1064SG/1164SG graphics accelerator> at 11.0 irq 10 pci0: <unknown card> (vendor=0x12eb, dev=0x0001) at 15.0 irq 11 <---- !! fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> on isa0 sc0: VGA <16 virtual consoles, flags=0x200> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 ------------------------------------------------------ my kernel config attached mpg123 says the following: ------------------------------------------------------- > mpg123 audio_file.mp3 High Performance MPEG 1.0/2.0/2.5 Audio Player for Layer 1, 2 and 3. Version 0.59r (1999/Jun/15). Written and copyrights by Michael Hipp. Uses code from various people. See 'README' for more! THIS SOFTWARE COMES WITH ABSOLUTELY NO WARRANTY! USE AT YOUR OWN RISK! Can't open /dev/dsp! ------------------------------------------------------- play says: ------------------------------------------------------- > play notify.wav play: /dev/dsp: Device not configured ------------------------------------------------------- devices seems to be ok: > ls -la /dev/snd* -rw-r--r-- 1 root wheel 5446 Jun 30 19:30 /dev/snd -rw-r--r-- 1 root wheel 5446 Jun 30 19:30 /dev/snd0 crw-rw-rw- 1 root wheel 30, 6 Jun 30 19:26 /dev/sndstat > ls -la /dev/dsp* lrwxrwxrwx 1 root wheel 4 Jun 30 19:26 /dev/dsp -> dsp0 crw-rw-rw- 1 root wheel 30, 3 Jun 30 19:26 /dev/dsp0 lrwxrwxrwx 1 root wheel 5 Jun 30 19:26 /dev/dspW -> dspW0 crw-rw-rw- 1 root wheel 30, 5 Jun 30 19:26 /dev/dspW0 My soundcard chipset is Vortex AU8820B2 On 30-Jun-2000 Mark Blackman wrote: > How about a copy of your kernel config file and some /sbin/dmesg > output that includes the device probes/initializations. > > what application are you trying to use and what error/condition are > you seeing? > > do you have the all the devices (/dev/snd*) made under /dev? > (cd /dev; sh MAKEDEV snd0) > > - Mark > > On Thu, Jun 29, 2000 at 11:55:51PM +0400, undef wrote: >> Hi, >> >> Ive got a Genius 'Sound Maker 64 PCI A3D` card and i dunno how get it worked >> under freebsd4.0. LINT kernel says that i need to include 'device pcm' into >> my >> kernel if i have PCI soundcard.. it dont works.. >> can u help me? >> >> thanx >> -- >> >> >> To Unsubscribe: send mail to majordomo@FreeBSD.org >> with "unsubscribe freebsd-multimedia" in the body of the message >> -- [-- Attachment #2 --] machine i386 cpu I386_CPU cpu I486_CPU cpu I586_CPU cpu I686_CPU ident KNOW maxusers 64 #makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols options MATH_EMULATE #Support for x87 emulation options INET #InterNETworking options INET6 #IPv6 communications protocols options FFS #Berkeley Fast Filesystem options FFS_ROOT #FFS usable as root device [keep this!] options MFS #Memory Filesystem options MD_ROOT #MD is a potential root device options NFS #Network Filesystem options NFS_ROOT #NFS usable as root device, NFS required options MSDOSFS options NTFS options CD9660 #ISO 9660 Filesystem options CD9660_ROOT #CD-ROM usable as root, CD9660 required options PROCFS #Process filesystem options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!] options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI options UCONSOLE #Allow users to grab the console options USERCONFIG #boot -c editor options VISUAL_USERCONFIG #visual boot -c editor options KTRACE #ktrace(1) support options SYSVSHM #SYSV-style shared memory options SYSVMSG #SYSV-style message queues options SYSVSEM #SYSV-style semaphores options P1003_1B #Posix P1003_1B real-time extentions options _KPOSIX_PRIORITY_SCHEDULING options ICMP_BANDLIM #Rate limit bad replies options VESA options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN options TCP_RESTRICT_RST #restrict emission of TCP RST options IPFIREWALL options IPSTEALTH #support for stealth forwarding # options TCPDEBUG # To make an SMP kernel, the next two are needed #options SMP # Symmetric MultiProcessor Kernel #options APIC_IO # Symmetric (APIC) I/O # Optionally these may need tweaked, (defaults shown): #options NCPU=2 # number of CPUs #options NBUS=4 # number of busses #options NAPIC=1 # number of IO APICs #options NINTR=24 # number of INTs device isa device eisa device pci # Floppy drives device fdc0 at isa? port IO_FD1 irq 6 drq 2 device fd0 at fdc0 drive 0 device fd1 at fdc0 drive 1 # ATA and ATAPI devices device ata0 at isa? port IO_WD1 irq 14 device ata1 at isa? port IO_WD2 irq 15 device ata device atadisk # ATA disk drives device atapicd # ATAPI CDROM drives device atapifd # ATAPI floppy drives device atapist # ATAPI tape drives options ATA_STATIC_ID #Static device numbering #options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI devices # SCSI Controllers device ahb # EISA AHA1742 family device ahc # AHA2940 and onboard AIC7xxx devices device amd # AMD 53C974 (Teckram DC-390(T)) device dpt # DPT Smartcache - See LINT for options! device isp # Qlogic family device ncr # NCR/Symbios Logic device sym # NCR/Symbios Logic (newer chipsets) device adv0 at isa? device adw device bt0 at isa? device aha0 at isa? device aic0 at isa? # SCSI peripherals device scbus # SCSI bus (required) device da # Direct Access (disks) device sa # Sequential Access (tape etc) device cd # CD device pass # Passthrough device (direct SCSI access) # RAID controllers device ida # Compaq Smart RAID device amr # AMI MegaRAID device mlx # Mylex DAC960 family # atkbdc0 controls both the keyboard and the PS/2 mouse device atkbdc0 at isa? port IO_KBD device atkbd0 at atkbdc? irq 1 device psm0 at atkbdc? irq 12 device vga0 at isa? # splash screen/screen saver pseudo-device splash # syscons is the default console driver, resembling an SCO console device sc0 at isa? # Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver #device vt0 at isa? #options XSERVER # support for X server on a vt console #options FAT_CURSOR # start with block cursor # If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines #options PCVT_SCANSET=2 # IBM keyboards are non-std # Floating point support - do not disable. device npx0 at nexus? port IO_NPX irq 13 # Power management support (see LINT for more options) device apm0 at nexus? disable flags 0x20 # Advanced Power Management # PCCARD (PCMCIA) support device card device pcic0 at isa? irq 10 port 0x3e0 iomem 0xd0000 device pcic1 at isa? irq 11 port 0x3e2 iomem 0xd4000 disable # Serial (COM) ports device sio0 at isa? port IO_COM1 flags 0x10 irq 4 device sio1 at isa? port IO_COM2 irq 3 device sio2 at isa? disable port IO_COM3 irq 5 device sio3 at isa? disable port IO_COM4 irq 9 # Parallel port device ppc0 at isa? irq 7 device ppbus # Parallel port bus (required) device lpt # Printer device plip # TCP/IP over parallel device ppi # Parallel port interface device #device vpo # Requires scbus and da # PCI Ethernet NICs. device de # DEC/Intel DC21x4x (``Tulip'') device fxp # Intel EtherExpress PRO/100B (82557, 82558) device tx # SMC 9432TX (83c170 ``EPIC'') device vx # 3Com 3c590, 3c595 (``Vortex'') device wx # Intel Gigabit Ethernet Card (``Wiseman'') # PCI Ethernet NICs that use the common MII bus controller code. device miibus # MII bus support device dc # DEC/Intel 21143 and various workalikes device rl # RealTek 8129/8139 device sf # Adaptec AIC-6915 (``Starfire'') device sis # Silicon Integrated Systems SiS 900/SiS 7016 device ste # Sundance ST201 (D-Link DFE-550TX) device tl # Texas Instruments ThunderLAN device vr # VIA Rhine, Rhine II device wb # Winbond W89C840F device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'') # ISA Ethernet NICs. device ed0 at isa? port 0x280 irq 10 iomem 0xd8000 device ex device ep # WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really # exists only as a PCMCIA device, so there is no ISA attatement needed # and resources will always be dynamically assigned by the pccard code. device wi # Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will # work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP # mode (the factory default). If you set the switches on your ISA # card for a manually chosen I/O address and IRQ, you must specify # those paremeters here. device an # The probe order of these is presently determined by i386/isa/isa_compat.c. device ie0 at isa? port 0x300 irq 10 iomem 0xd0000 device fe0 at isa? port 0x300 device le0 at isa? port 0x300 irq 5 iomem 0xd0000 device lnc0 at isa? port 0x280 irq 10 drq 0 device cs0 at isa? port 0x300 device sn0 at isa? port 0x300 irq 10 # requires PCCARD (PCMCIA) support to be activated #device xe0 at isa? #devive snd0 device pcm # Pseudo devices - the number indicates how many units to allocated. pseudo-device loop # Network loopback pseudo-device ether # Ethernet support pseudo-device sl 1 # Kernel SLIP pseudo-device ppp 1 # Kernel PPP pseudo-device tun # Packet tunnel. pseudo-device pty # Pseudo-ttys (telnet etc) pseudo-device md # Memory "disks" pseudo-device gif 4 # IPv6 and IPv4 tunneling pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation) pseudo-device bpf 32 pseudo-device vn # The `bpf' pseudo-device enables the Berkeley Packet Filter. # Be aware of the administrative consequences of enabling this! pseudo-device bpf #Berkeley packet filter # USB support #device uhci # UHCI PCI->USB interface #device ohci # OHCI PCI->USB interface #device usb # USB Bus (required) #device ugen # Generic #device uhid # "Human Interface Devices" #device ukbd # Keyboard #device ulpt # Printer #device umass # Disks/Mass storage - Requires scbus and da #device ums # Mouse # USB Ethernet, requires mii #device aue # ADMtek USB ethernet #device cue # CATC USB ethernet #device kue # Kawasaki LSI USB ethernethelp
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?XFMail.20000630193356.hideout>