Date: Tue, 25 Nov 2014 17:33:23 +0000 (UTC) From: Sean Bruno <sbruno@FreeBSD.org> To: src-committers@freebsd.org, svn-src-all@freebsd.org, svn-src-head@freebsd.org Subject: svn commit: r275057 - head/sys/mips/conf Message-ID: <201411251733.sAPHXN9s081855@svn.freebsd.org>
next in thread | raw e-mail | index | archive | help
Author: sbruno Date: Tue Nov 25 17:33:22 2014 New Revision: 275057 URL: https://svnweb.freebsd.org/changeset/base/275057 Log: Add support for Buffalo WZR-HP-AG300H atheros MIPS router. Special thanks to Nicholas Esborn for the loaner router to get this target bootstrapped. Review: D777 Reviewed by: adrian Sponsored by: Nicholas Esborn <nick@desert.net> Added: head/sys/mips/conf/WZR-HPAG300H (contents, props changed) head/sys/mips/conf/WZR-HPAG300H.hints (contents, props changed) Added: head/sys/mips/conf/WZR-HPAG300H ============================================================================== --- /dev/null 00:00:00 1970 (empty, because file is newly added) +++ head/sys/mips/conf/WZR-HPAG300H Tue Nov 25 17:33:22 2014 (r275057) @@ -0,0 +1,49 @@ +# +# Specific board setup for the Buffalo Airstation WZR-HPAG300H +# +# The WZR-HPAG300H has the following hardware: +# +# + AR7161 CPU SoC +# + 2x AR9280 5GHz 11n +# + AR8136 Gigabit switch +# + 2 m25ll128(really w25q128) based 16MB flash +# + 128MB RAM +# + uboot environment + +# $FreeBSD$ + +include "AR71XX_BASE" +ident "WZR-HPAG300H" +hints "WZR-HPAG300H.hints" + +options AR71XX_REALMEM=128*1024*1024 + +options AR71XX_ENV_UBOOT + +options BOOTVERBOSE + +# GEOM modules +device geom_uncompress # compressed in-memory filesystem hackery! +device geom_map # to get access to the SPI flash partitions + +options ROOTDEVNAME=\"ufs:/dev/map/rootfs.uncompress\" + +options AR71XX_ATH_EEPROM # Fetch EEPROM/PCI config from flash +options ATH_EEPROM_FIRMWARE # Use EEPROM from flash +device firmware # Used by the above + +# Options required for miiproxy and mdiobus +options ARGE_MDIO # Export an MDIO bus separate from arge +device miiproxy # MDIO bus <-> MII PHY rendezvous + +device etherswitch +device arswitch + +# hwpmc +device hwpmc_mips24k +device hwpmc + +# load these via modules, shrink kernel +nodevice if_bridge +nodevice bridgestp +nodevice random Added: head/sys/mips/conf/WZR-HPAG300H.hints ============================================================================== --- /dev/null 00:00:00 1970 (empty, because file is newly added) +++ head/sys/mips/conf/WZR-HPAG300H.hints Tue Nov 25 17:33:22 2014 (r275057) @@ -0,0 +1,132 @@ +# $FreeBSD$ + +# arge0 is connected to the LAN side of the switch PHY. +# arge1 is connected to the single port WAN side of the switch PHY. + +# arge1 MDIO bus +hint.argemdio.0.at="nexus0" +hint.argemdio.0.maddr=0x1a000000 +hint.argemdio.0.msize=0x1000 +hint.argemdio.0.order=0 + +hint.arge.0.phymask=0x0 +hint.arge.0.media=1000 +hint.arge.0.fduplex=1 +hint.arge.0.eeprommac=0x1f05120c +hint.arge.0.mdio=mdioproxy0 # .. off of the switch mdiobus +hint.arge.0.miimode=3 + +hint.arge.1.phymask=0x10 +hint.arge.1.media=1000 +hint.arge.1.fduplex=1 +hint.arge.1.eeprommac=0x1f05520c +hint.arge.1.mdio=mdioproxy0 # .. off of the switch mdiobus +hint.arge.1.miimode=3 +# +# AR7240 switch config +# +hint.arswitch.0.at="mdio0" +hint.arswitch.0.is_7240=0 # We need to be explicitly told this +hint.arswitch.0.numphys=4 # 5 active switch PHYs (PHY 0 -> 4) +hint.arswitch.0.phy4cpu=0 # No, PHY 4 == dedicated PHY +hint.arswitch.0.is_rgmii=1 # Yes, is RGMII +hint.arswitch.0.is_gmii=0 # No, not GMII + +# ath0 - slot 17 +hint.pcib.0.bus.0.17.0.ath_fixup_addr=0x1f051000 +hint.pcib.0.bus.0.17.0.ath_fixup_size=4096 + +# ath1 - slot 18 +hint.pcib.0.bus.0.18.0.ath_fixup_addr=0x1f055000 +hint.pcib.0.bus.0.18.0.ath_fixup_size=4096 +# .. and now, telling each ath(4) NIC where to find the firmware +# image. +hint.ath.0.eeprom_firmware="pcib.0.bus.0.17.0.eeprom_firmware" +hint.ath.1.eeprom_firmware="pcib.0.bus.0.18.0.eeprom_firmware" + +# Inherited from AR71XX_BASE.hints +#hint.mx25l.0.at="spibus0" +#hint.mx25l.0.cs=0 +# This board has two 16 MB flash devices on difference Chip Select pins +hint.mx25l.1.at="spibus0" +hint.mx25l.1.cs=1 + + +# Geom MAP + +hint.map.0.at="flash/spi0" +hint.map.0.start=0x00000000 +hint.map.0.end=0x00040000 +hint.map.0.name="uboot" +hint.map.0.readonly=1 + +hint.map.1.at="flash/spi0" +hint.map.1.start=0x00040000 +hint.map.1.end=0x00050000 +hint.map.1.name="u-boot-env" +hint.map.1.readonly=1 + +hint.map.2.at="flash/spi0" +hint.map.2.start=0x00050000 +hint.map.2.end=0x00060000 +hint.map.2.name="ART" +hint.map.2.readonly=1 + +# requires a 1M alignment and padding in the image. +# make sure you are using conv=sync and bs=1M in your dd +hint.map.3.at="flash/spi0" +hint.map.3.start=0x00060000 +hint.map.3.end="search:0x00160000:0x100000:.!/bin/sh" +hint.map.3.name="kernel" +hint.map.3.readonly=1 + +hint.map.4.at="flash/spi0" +hint.map.4.start="search:0x00160000:0x100000:.!/bin/sh" +hint.map.4.end=0x01000000 +hint.map.4.name="rootfs" +hint.map.4.readonly=1 + +hint.map.5.at="flash/spi1" +hint.map.5.start=0x00FF0000 +hint.map.5.end=0x01000000 +hint.map.5.name="cfg" +hint.map.5.readonly=0 + +# Pin 1 - SCK +# Pin 2 - SDA +# Pin 3 - usb +# Pin 4 - +# Pin 5 - aoss +# Pin 6 - router auto +# Pin 7 - router off +# Pin 8 - movie engine +# Pin 9 - +# Pin 10 - +# Pin 11 - reset button +# Pin 12 - CS0 +# Pin 13 - CS1 +# Pin 14 - +# Pin 15 - +# Pin 16 - +# Pin 17 - + +# Don't flip on anything that isn't already enabled. +# Force on CS lines for flash devices, apparently this isn't done +# by uboot in normal booting. No idea why. +hint.gpio.0.function_set=0x00003004 +hint.gpio.0.function_clear=0x00000000 + +# These are the GPIO LEDs and buttons which can be software controlled. +hint.gpio.0.pinmask=0x0001 + +hint.gpio.0.pinon=0x00000004 + +hint.gpioiic.0.at="gpiobus0" +#hint.gpioiic.0.pins=0x0003 +hint.gpioiic.0.sda=0 +hint.gpioiic.0.scl=1 + +# LEDs are configured separately and driven by the LED device +hint.gpioled.0.at="gpiobus0" +hint.gpioled.0.name="red-diag" +hint.gpioled.0.pins=0x0001
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?201411251733.sAPHXN9s081855>