Date: Tue, 1 Jul 2003 22:09:57 -0600 From: "Kenneth D. Merry" <ken@kdm.org> To: "M. Warner Losh" <imp@bsdimp.com> Cc: mobile@freebsd.org Subject: Re: cardbus network problem with -current Message-ID: <20030701220957.A8089@panzer.kdm.org> In-Reply-To: <20030701.173218.60741055.imp@bsdimp.com>; from imp@bsdimp.com on Tue, Jul 01, 2003 at 05:32:18PM -0600 References: <20030628234509.A90521@panzer.kdm.org> <20030701.173218.60741055.imp@bsdimp.com>
next in thread | previous in thread | raw e-mail | index | archive | help
--UugvWAfsgieZRqgk
Content-Type: text/plain; charset=us-ascii
Content-Disposition: inline
On Tue, Jul 01, 2003 at 17:32:18 -0600, M. Warner Losh wrote:
> Can you turn on the following debugging and try again? Also, please
> post questions relating to cardbus/pccard to mobile@ since I read that
> more often than I read current@. Thanks much.
>
> hw.cardbus.debug: 1
> hw.cardbus.cis_debug: 1
> hw.cbb.debug: 1
Okay, here is dmesg output with those variables set.
All I did was boot with the card inserted in the slot, and then after the
machine booted, I pulled it out and re-inserted it.
Thanks!
Ken
--
Kenneth Merry
ken@kdm.org
--UugvWAfsgieZRqgk
Content-Type: text/plain; charset=us-ascii
Content-Disposition: attachment; filename="erebor.dmesg.20030701"
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.1-CURRENT #0: Mon Jun 30 21:32:23 MDT 2003
ken@nargothrond.kdm.org:/usr/home/ken/perforce2/FreeBSD-ken/src/sys/i386/compile/erebor
Preloaded elf kernel "/boot/kernel/kernel" at 0xc067e000.
Preloaded acpi_dsdt "/boot/acpi_dsdt.aml" at 0xc067e1cc.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc067e214.
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 2492656604 Hz
CPU: Mobile Intel(R) Pentium(R) 4 - M CPU 2.50GHz (2492.66-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf27 Stepping = 7
Features=0xbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
real memory = 536535040 (511 MB)
avail memory = 514105344 (490 MB)
Pentium Pro MTRR support enabled
ACPI: DSDT was overridden.
ACPI-0375: *** Info: Table [DSDT] replaced by host OS
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL CPi R > on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 9 entries at 0xc00fc590
Timecounter "ACPI-fast" frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
acpi_cpu0: <CPU> port 0x530-0x537 on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_acad0: <AC adapter> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_cmbat1: <Control method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib0: slot 29 INTA is routed to irq 11
pcib0: slot 29 INTB is routed to irq 11
pcib0: slot 29 INTC is routed to irq 11
pcib0: slot 29 INTD is routed to irq 11
pcib0: slot 31 INTB is routed to irq 11
pcib0: slot 31 INTB is routed to irq 11
agp0: <Intel 82845 host to AGP bridge> mem 0xec000000-0xefffffff at device 0.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib1: slot 0 INTA is routed to irq 11
pci1: <display, VGA> at device 0.0 (no driver attached)
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xbf80-0xbf9f irq 11 at device 29.0 on pci0
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xbf40-0xbf5f irq 11 at device 29.1 on pci0
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xbf20-0xbf3f irq 11 at device 29.2 on pci0
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3: vendor 0x413c product 0x0058, class 9/0, rev 2.00/0.00, addr 2
device_probe_and_attach: uhub3 attach returned 6
uhub3: vendor 0x413c product 0x0058, class 9/0, rev 2.00/0.00, addr 2
device_probe_and_attach: uhub3 attach returned 6
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf4fffc00-0xf4ffffff irq 11 at device 29.7 on pci0
ehci_pci_attach: companion usb0
ehci_pci_attach: companion usb1
ehci_pci_attach: companion usb2
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <EHCI (generic) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: (0x8086) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
usb3: unrecoverable error, controller halted
usb3: blocking intrs 0x10
uhub3: device problem, disabling port 6
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib2: slot 0 INTA is routed to irq 11
pcib2: slot 1 INTA is routed to irq 11
pcib2: slot 3 INTA is routed to irq 11
pci2: <network, ethernet> at device 0.0 (no driver attached)
cbb0: <TI4510 PCI-CardBus Bridge> at device 1.0 on pci2
cbb0: PCI Memory allocated: f6000000
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
pcib2: slot 1 INTA is routed to irq 11
fwohci0: vendor=104c, dev=8029
fwohci0: <1394 Open Host Controller Interface> mem 0xfaff8000-0xfaffbfff,0xfaffd800-0xfaffdfff irq 11 at device 1.1 on pci2
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 38:4f:c0:00:08:9c:ec:41
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
if_fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 3a:4f:c0:9c:ec:41
sbp0: <SBP2/SCSI over firewire> on firewire0
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
pci2: <network> at device 3.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port 0xbfa0-0xbfaf,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pcm0: <Intel 82801DB (ICH4)> port 0xbc40-0xbc7f,0xb800-0xb8ff mem 0xf4fff400-0xf4fff4ff,0xf4fff800-0xf4fff9ff irq 11 at device 31.5 on pci0
pcm0: <SigmaTel STAC9750/51 AC97 Codec>
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 1 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/7 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
orm0: <Option ROMs> at iomem 0xcf800-0xcffff,0xc0000-0xcf7ff on isa0
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
cbb0: card inserted: event=0x00000000, state=30000820
cbb0: cbb_power: 3V
cardbus0: Resource not specified in CIS: id=10, size=2000
cardbus0: Non-prefetchable memory at f6002000-f6003fff
cardbus0: <network, ethernet> at device 0.0 (no driver attached)
cbb0: cbb_power: 0V
cbb0: CardBus card activation failed
ata1-slave: timeout waiting for interrupt
ata1-slave: ATA identify failed
ad0: 57231MB <FUJITSU MHS2060AT> [116280/16/63] at ata0-master UDMA100
acd0: CD-RW <PHILIPS DVD+RW SDVD6004> at ata1-master WDMA2
Mounting root from ufs:/dev/ad0s3a
cd0 at ata1 bus 0 target 0 lun 0
cd0: <PHILIPS DVD+RW SDVD6004 0.99> Removable CD-ROM SCSI-0 device
cd0: 16.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
cbb0: card inserted: event=0x00000002, state=30000820
cbb0: cbb_power: 3V
TUPLE: LINKTARGET [3]: 43 49 53
Product version: 5.0
Product name: INTEL(R) | PRO/100 CARDBUS II | MBLA3300 | 1.00 |
TUPLE: Unknown(0x88) [4]: 2b 82 49 00
TUPLE: Unknown(0x8a) [12]: 39 30 30 32 39 47 34 39 38 32 32 42
TUPLE: Unknown(0x8b) [4]: 00 00 00 00
Manufacturer ID: 89000301c1
TUPLE: DATE [4]: 2a 65 84 2a
Functions: Network Adaptor, Multi-Functioned
Function Extension: 040600034749822b
Function Extension: 0102
Function Extension: 0280969800
Function Extension: 0200e1f505
TUPLE: DEVICE_OC [2]: 02 ff
cardbus0: Opening BAR: type=MEM, bar=10, len=1000 (Prefetchable)
cardbus0: Opening BAR: type=IO, bar=14, len=0040
cardbus0: Opening BAR: type=MEM, bar=18, len=20000 (Prefetchable)
CIS reading done
cardbus0: Prefetchable memory at f6020000-f6040fff
cardbus0: IO port at 1000-103f
fxp0: <Intel 82557/8/9 EtherExpress Pro/100(B) Ethernet> port 0x1000-0x103f mem 0xf6020000-0xf603ffff,0xf6040000-0xf6040fff irq 11 at device 0.0 on cardbus0
fxp0: Ethernet address 00:03:47:49:82:2b
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
--UugvWAfsgieZRqgk--
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20030701220957.A8089>