Date: Fri, 26 May 2000 17:03:39 -0500 (CDT) From: Kevin Day <toasty@dragondata.com> To: msmith@FreeBSD.ORG (Mike Smith) Cc: dburr@borg-cube.com (Donald Burr), freebsd-questions@FreeBSD.ORG (FreeBSD Questions), freebsd-hardware@FreeBSD.ORG (FreeBSD Hardware) Subject: Re: UDMA ICRC errors on FIC SD11 Athlon board and U66 HD -- huh?! Message-ID: <200005262203.RAA84505@celery.dragondata.com> In-Reply-To: <200005161939.MAA02841@mass.cdrom.com> from "Mike Smith" at May 16, 2000 12:39:57 PM
next in thread | previous in thread | raw e-mail | index | archive | help
>
> > Ok, I just put together a new Athlon system, and am having a hell of a
> > time trying to get the hard disks to work right.
> >
> > First, some system details:
> >
> > Motherboard: FIC SD-11 board rev. 1.8, with the latest BIOS.
> > (AMD-751 north bridge, VIA 82C686 south bridge)
> > CPU: AMD Athlon 650MHz.
> > Memory: 128MB SDRAM DIMM
> > Hard Disk: Western Digital Caviar WD102AA 10.2 GB Ultra66
> > (single drive only, no slave devices or CD-ROM's etc.)
> ...
> > ad0: UDMA ICRC WRITE ERROR blk# 27984ata0-master: WARNING: WAIT_READY
> > active=ATA_ACTIVE_ATA
> > falling back to PIO mode
>
> I'm seeing exactly the same symptoms, but with a slightly faster CPU and
> an IBM disk. I'm not entirely sure what the real deal here is; it's
> possible that there may be eg. some timing values that aren't being set
> quite right for this board/chipset. 8(
>
If this helps any, I see this here too:
FreeBSD 4.0-STABLE #1: Fri May 26 14:37:18 CDT 2000
toasty@catapult.video:/usr/src/sys/compile/CATAPULT
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (365.48-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x665 Stepping = 5
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 132907008 (129792K bytes)
avail memory = 125833216 (122884K bytes)
pnpbios: Bad PnP BIOS data checksum
Preloaded elf kernel "kernel" at 0xc034f000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82810E (i810E GMCH) Host To Hub bridge> on motherboard
pci0: <PCI bus> on pcib0
pci0: <Intel 82810E (i810E GMCH) SVGA controller> at 1.0 irq 11
pcib1: <Intel 82801AA (ICH) Hub to PCI bridge> at device 30.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x1274, dev=0x1371) at 7.0 irq 11
ti0: <3Com 3c985-SX Gigabit Ethernet> mem 0xff8f8000-0xff8fbfff irq 11 at device 8.0 on pci1
ti0: Ethernet address: 00:60:08:f5:d0:b0
ti0: supplying EUI64: 00:60:08:ff:fe:f5:d0:b0
fxp0: <Intel EtherExpress Pro 10/100B Ethernet> port 0xdf00-0xdf3f mem 0xff700000-0xff7fffff,0xff8ff000-0xff8fffff irq 10 at device 9.0 on pci1
fxp0: Ethernet address 00:90:27:c2:09:87
isab0: <Intel 82801AA (ICH) PCI to LPC bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH ATA66 controller> port 0xffa0-0xffaf at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82801AA (ICH) USB controller> at 31.2 irq 9
pci0: <unknown card> (vendor=0x8086, dev=0x2413) at 31.3 irq 10
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
psm0: failed to get data.
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
ad0: 6149MB <QUANTUM FIREBALL CX6.4A> [13328/15/63] at ata0-master using UDMA33
acd0: CDROM <SONY CD-ROM CDU4821> at ata1-master using PIO4
Mounting root from ufs:/dev/ad0s1a
vinum: loaded
ad0: UDMA ICRC WRITE ERROR blk# 2111 retrying
ad0: UDMA ICRC WRITE ERROR blk# 2111 retrying
ad0: WRITE command timeout - resetting
ata0: resetting devices .. done
ad0: UDMA ICRC WRITE ERROR blk# 2111ata0-master: WARNING: WAIT_READY active=ATA_ACTIVE_ATA
falling back to PIO mode
fxp0: starting DAD for fe80:0002::0290:27ff:fec2:0987
fxp0: DAD complete for fe80:0002::0290:27ff:fec2:0987 - no duplicates found
The part about the bad pnp checksum kinda worries me too. :)
If there's anything someone would like me to try, I'm willing.
-- Kevin
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200005262203.RAA84505>