Date: Thu, 27 May 1999 18:25:49 +0300 From: "Andy V. Oleynik" <andyo@prime.net.ua> To: Kazutaka YOKOTA <yokota@zodiac.mech.utsunomiya-u.ac.jp> Cc: freebsd-stable@freebsd.org Subject: Re: Oddness while switching between console & X Message-ID: <374D63FD.4FB4E9FD@prime.net.ua> References: <373C6FA4.4EAAE0C4@prime.net.ua> <199905271356.WAA26219@zodiac.mech.utsunomiya-u.ac.jp>
next in thread | previous in thread | raw e-mail | index | archive | help
XFree86 Version 3.3.3.1 / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: January 4 1999
If the server is older than 6-12 months, or if your card is
newer
than the above date, look for a newer version before reporting
problems. (see http://www.XFree86.Org/FAQ)
Operating System: FreeBSD 3.2-BETA i386 [ELF]
Configured drivers:
S3: accelerated server for S3 graphics adaptors (Patchlevel 0)
newmmio, mmio_928, s3_generic
Using syscons driver with X support (version 2.0)
(using VT number 4)
XF86Config: /etc/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: keycodes: "xfree86"
(**) XKB: keymap: "xfree86(ru)" (overrides other XKB settings)
(**) XKB: types: "default"
(**) XKB: compat: "default"
(**) XKB: symbols: "us(pc101)"
(**) XKB: geometry: "pc"
(**) XKB: rules: "xfree86"
(**) XKB: model: "pc104"
(**) XKB: layout: "ru"
(**) XKB: options: "ctrl:ctrl_aa,grp:ctrl_shift_toggle"
(**) Mouse: type: Microsoft, device: /dev/cuaa0, baudrate: 1200
(**) Mouse: buttons: 3, 3 button emulation (timeout: 50ms)
(**) S3: Graphics device ID: "Trio64V+"
(**) S3: Monitor ID: "AMIGA"
(**) FontPath set to
"/usr/X11R6/lib/X11/fonts/cyrillic/,/usr/X11R6/lib/X11/fonts/ukr/,/usr/X11R6/lib
/X11/fonts/cyrillic/WinCronyx/,/usr/X11R6/lib/X11/fonts/cyrillic/misc/,/usr/X11R6/lib/X11/fonts/cyril
lic/75dpi/,/usr/X11R6/lib/X11/fonts/cyrillic/100dpi/,/usr/X11R6/lib/X11/fonts/75dpi/:unscaled,/usr/X1
1R6/lib/X11/fonts/100dpi/:unscaled,/usr/X11R6/lib/X11/fonts/Type1/,/usr/X11R6/lib/X11/fonts/Speedo/"
(--) S3: PCI: Trio32/64 rev 44, Linear FB @ 0xe0000000
(--) S3: chipset: Trio64V+ rev. 44
(**) S3: chipset driver: s3_generic
(**) S3: Option "trio64v+_bug1"
(**) S3: Option "trio64v+_bug2"
(**) S3: Option "trio64v+_bug3"
(--) S3: card type: PCI
(**) S3: videoram: 1024k
(**) S3: Ramdac type: s3_trio64
(--) S3: Ramdac speed: 135 MHz
(**) S3: Using Trio32/64 programmable clock (MCLK 59.957 MHz)
(--) S3: Maximum allowed dot-clock: 135.000 MHz
(**) S3: Mode "1024x768": mode clock = 44.900
(**) S3: Mode "800x600": mode clock = 36.000
(**) S3: Mode "640x480": mode clock = 25.180
(--) S3: Operating RAMDAC in pixel multiplex mode
(--) S3: Using 6 bits per RGB value
(**) S3: Virtual resolution set to 1024x768
(--) S3: Local bus LAW is 0xE0000000
(--) S3: Using a banksize of 1024k, line width of 1024
(--) S3: Using a single 64x64 area at (960,769) for expanding pixmaps
(--) S3: Using 8 planes of 960x255 at (0,769) aligned 8 as font cache
Problem persists
Kazutaka YOKOTA wrote:
> >Ok, this morning I've began
> >to rebuid XFree86 sources to elf format.
>
> Which version of XFree86 are you talking about?
>
> Kazu
>
> >After rebuld & restart X (I run xdm),
> >Just after switchig in X, it's fozen
> >untill I rebooted by reset (I should not
> >do that 'cos it was alive). Next
> >start of X just did the same.
> >But as I said earlier it was alive.
> >It was pinged, ftp'd, smtp'd but
> >its console & kbd was frozen anyway.
> >Only after being ssh'd it became melted
> >and did worked properly. Ok. Look.
> >I switch from console to X with ALT-*.
> >Turning into X kbd, mouse, screen becomes
> >frozen until I remotly ssh this host
> >(just after "ssh xhost<CR>" - no more).
> >well, I turn into console. result is
> >console, kbd become frozen again untill
> >I remotly "ssh xhost<CR>". Etc.
> >Being not switched between modes system works just
> >fine. I'll resolve this prob anyway.
> >But U, guys, what do U think about it?
> >Seems like ssh protocol do some strobe
> >making kbd, screen & mouse to become
> >alive after switching from mode to mode.
> >And only when ssh *starts* from remote.
> >No errors in any logs, no traffic on lo0,
> >just normal traffic on ed0 ssh/tcp.
--
WBW Andy V. Oleynik (When U work in virtual office
U have good chance to obtain virtual money ö%-)
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?374D63FD.4FB4E9FD>