Date: Mon, 05 Feb 2007 11:22:26 +0100 From: Simon Thoustrup <simon@thoustrup.dk> To: freebsd-multimedia@freebsd.org Subject: Re: Tuner code 0x71 for Hauppauge PVR-150 (pvrxxx) Message-ID: <45C70562.5040308@thoustrup.dk> In-Reply-To: <c39ec84c0702041403i2ad28efax51723731cc50c61e@mail.gmail.com> References: <45B91790.9080206@thoustrup.dk> <200701281627.23403.josh@tcbug.org> <45C60C4D.7030500@thoustrup.dk> <c39ec84c0702041403i2ad28efax51723731cc50c61e@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
usleepless@gmail.com wrote: >> It takes a lot longer to load the cxm module now, but I still get: >> >> kernel: cxm0: <Conexant iTVC16 MPEG Coder> mem 0xd0000000-0xd3ffffff irq >> 9 at device 13.0 on pci0 >> kernel: cxm_iic0: <Conexant iTVC15 / iTVC16 I2C controller> on cxm0 >> kernel: iicbb0: <I2C bit-banging driver> on cxm_iic0 >> kernel: iicbus0: <Philips I2C bus> on iicbb0 master-only >> kernel: tuner code 113 >> kernel: tuner_type = 20 >> kernel: cxm0: TCL 2002N-6A tuner >> kernel: <2>cxm 0-0000: loaded /lib/modules/v4l-cx25840.fw firmware >> (16382 bytes) >> kernel: <2>cxm debug 0-0000: decoder set input (0) >> kernel: <2>cxm debug 0-0000: now setting Tuner input >> kernel: <2>cxm debug 0-0000: set audio input (0) >> kernel: <2>cxm debug 0-0000: set audio input (0) >> kernel: cxm0: Eeprom PAL >> kernel: <2>tda 0-0000: switching to v4l2 >> kernel: <2>tda 0-0000: configure for: PAL-BG >> kernel: <2>tda 0-0000: writing: b=0xd4 c=0x70 e=0x09 >> kernel: could not start iic bus >> kernel: probed 54 >> kernel: probed 136 >> kernel: probed 160 >> kernel: probed 194 >> kernel: probed 224 >> kernel: probed 226 >> kernel: probed 228 >> kernel: probed 230 >> kernel: <2>tda 0-0000: i2c i/o error: rc == 2 (should be 4) >> kernel: read error >> kernel: <2>tda 0-0000: i2c i/o error: rc == -597317209 (should be 1) >> kernel: <2>tda 0-0000: read: 0x 0 >> kernel: <2>tda 0-0000: after power on : no >> kernel: <2>tda 0-0000: afc : - 12.5 kHz >> kernel: <2>tda 0-0000: fmif level : low >> kernel: <2>tda 0-0000: afc window : out >> kernel: <2>tda 0-0000: vfi level : low >> kernel: <2>cxm 0-0000: Video signal: not present >> kernel: <2>cxm 0-0000: Detected format: NTSC-M >> kernel: <2>cxm 0-0000: Detected audio mode: forced mode >> kernel: <2>cxm 0-0000: Detected audio standard: forced audio standard >> kernel: <2>cxm 0-0000: Audio muted: no >> kernel: <2>cxm 0-0000: Audio microcontroller: running >> kernel: <2>cxm 0-0000: Configured audio standard: A2-BG >> kernel: <2>cxm 0-0000: Configured audio mode: undefined >> kernel: <2>cxm 0-0000: Specified standard: PAL-BDGHI >> kernel: <2>cxm 0-0000: Specified input: Tuner >> kernel: <2>cxm 0-0000: Specified audio input: Tuner >> kernel: <2>cxm 0-0000: Specified audioclock freq: 48 kHz >> kernel: <2>cxm 0-0000: Preferred audio mode: stereo >> kernel: <2>cxm 0-0000: Selected 65 MHz format: system DK >> kernel: <2>cxm 0-0000: Selected 45 MHz format: chroma >> kernel: cxm0: [GIANT-LOCKED] >> bsd kernel: cxm0: encoder firmware version 0x2050032 >> >> - and still the same error messages when trying pvr250-setchannel: >> >> ioctl( tfd, BT848_GAUDIO ) failed.: Device not configured >> ioctl( tfd, TVTUNER_SETTYPE ) failed.: Invalid argument > > what are the exact parameters you are supplying to pvr250-setchannel? # pvr250-setchannel -a on -m 4 231.25 ioctl( tfd, BT848_GAUDIO ) failed.: Device not configured ioctl( tfd, TVTUNER_SETTYPE ) failed.: Invalid argument # pvr250-setchannel -m 4 231.25 ioctl( tfd, BT848_GAUDIO ) failed.: Device not configured ioctl( tfd, TVTUNER_SETTYPE ) failed.: Invalid argument # pvr250-setchannel 231.25 ioctl( tfd, BT848_GAUDIO ) failed.: Device not configured # pvr250-setchannel -a on -m 4 11 ioctl( tfd, BT848_GAUDIO ) failed.: Device not configured ioctl( tfd, TVTUNER_SETTYPE ) failed.: Invalid argument ioctl( tfd, TVTUNER_SETCHNL ) failed.: Invalid argument # pvr250-setchannel -m 4 11 ioctl( tfd, BT848_GAUDIO ) failed.: Device not configured ioctl( tfd, TVTUNER_SETTYPE ) failed.: Invalid argument ioctl( tfd, TVTUNER_SETCHNL ) failed.: Invalid argument # pvr250-setchannel 11 ioctl( tfd, BT848_GAUDIO ) failed.: Device not configured ioctl( tfd, TVTUNER_SETCHNL ) failed.: Invalid argument As Dan also points out in his mail, I didn't expect pvr250-setchannel to work as it should with the i2c bus not starting correctly, but tried it out in case it was just a "print-error"/warning.. Regards, Simon
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?45C70562.5040308>