Date: Sat, 1 Jul 2000 01:19:43 -0700 (PDT) From: Arthur Chang <FreeBSD@irelands.org> To: freebsd-mobile@FreeBSD.ORG Subject: Help needed for pcmcia card Message-ID: <20000701081943.7BD43E0B5@sitemail.everyone.net>
next in thread | raw e-mail | index | archive | help
I understand that this is not the right place to pose
a question. But I'm so desprate to get my pcmcia card
working and no one have reply me at freebsd-question.
System:-
Toshiba 300CDS Notebook
FreeBSD Releases 4.0
Pcmcia Card:-
Prolink V.90 pcmcia modem (model 1456c)
Socket Communication INC serial adapter
I've tried to use other setting on the mailing archive,
and the configuration from pccard.conf.sample. But
none of which is working with my hardware. Some even
hang the whole system.
I've new to FreeBSD and hope to have some clue getting
it to work.
Thank You
P.S: my pccardc dumpics output as follow:
Code 135 not found
Code 135 not found
code Unknown ignored
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 2
000: 00 ff
Common memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = reserved, 32 units
Tuple #2, code = 0x15 (Version 1 info), length = 48
000: 05 00 50 43 4d 43 49 41 20 20 00 35 36 4b 20 56
010: 2e 39 30 20 46 61 78 20 4d 6f 64 65 6d 20 28 4c
020: 4b 29 20 20 00 46 4d 35 36 30 4c 4b 20 20 00 ff
Version = 5.0, Manuf = [PCMCIA ],card vers = [56K V.90 Fax Modem (LK) ]
Addit. info = [FM560LK ]
Tuple #3, code = 0x20 (Manufacturer ID), length = 4
000: 75 01 00 00
PCMCIA ID = 0x175, OEM ID = 0x0
Tuple #4, code = 0x21 (Functional ID), length = 2
000: 02 00
Serial port/modem
Tuple #5, code = 0x22 (Functional EXT), length = 4
000: 00 02 0f 5c
Serial interface extension:
16550 UART, Parity - Space,Mark,Odd,Even,
Tuple #6, code = 0x22 (Functional EXT), length = 9
000: 05 1f 1f 00 04 00 00 04 00
Modem interface capabilities:
Tuple #7, code = 0x22 (Functional EXT), length = 9
000: 06 1f 1f 00 04 00 00 04 00
Modem interface capabilities:
Tuple #8, code = 0x22 (Functional EXT), length = 12
000: 02 06 00 3f 1c 03 03 0f 07 00 01 b5
Data modem services available:
Tuple #9, code = 0x22 (Functional EXT), length = 8
000: 13 06 00 1f 00 02 00 b5
Tuple #10, code = 0x22 (Functional EXT), length = 8
000: 23 06 00 1f 00 02 00 b5
Tuple #11, code = 0x1a (Configuration map), length = 5
000: 01 27 80 ff 67
Reg len = 2, config register addr = 0xff80, last config = 0x27
Registers: XXX--XX-
Tuple #12, code = 0x1b (Configuration entry), length = 19
000: cf 41 99 79 55 3d 86 46 26 4c aa 60 f8 03 07 f0
010: bc 86 28
Config index = 0xf(default)
Interface byte = 0x41 (I/O) +RDY/-BSY active
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Continuous supply current: 3.5 x 10mA
Max current average over 1 second: 1 x 100mA, ext = 0x46
Max current average over 10 ms: 2 x 100mA
Power down supply current: 4.5 x 1mA
Card decodes 10 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x3f8 block length = 0x8
IRQ modes: Level, Pulse, Shared
IRQs: 4 5 6 7 10 11 12 13 15
Max twin cards = 0
Misc attr: (Audio-BVD2) (Power down supported)
Tuple #13, code = 0x1b (Configuration entry), length = 7
000: 17 08 aa 60 f8 02 07
Config index = 0x17
Card decodes 10 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x2f8 block length = 0x8
Tuple #14, code = 0x1b (Configuration entry), length = 7
000: 1f 08 aa 60 e8 03 07
Config index = 0x1f
Card decodes 10 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x3e8 block length = 0x8
Tuple #15, code = 0x1b (Configuration entry), length = 7
000: 27 08 aa 60 e8 02 07
Config index = 0x27
Card decodes 10 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x2e8 block length = 0x8
Tuple #16, code = 0x0 (Null tuple), length = 7
000: 41 45 49 23 37 a1 00
Tuple #17, code = 0x14 (No link), length = 0
Tuple #18, code = 0xff (Terminator), length = 0
Configuration data for card in slot 1
Tuple #1, code = 0x1 (Common memory descriptor), length = 2
000: d4 3a
Common memory device information:
Device number 1, type Function specific, WPS = OFF
Speed = 100nS, Memory block size = 8Kb, 8 units
Tuple #2, code = 0x10 (Checksum), length = 5
000: 07 00 e8 00 6f
Checksum from offset 7, length 232, value is 0x6f
Tuple #3, code = 0x17 (Attribute memory descriptor), length = 2
000: d4 3a
Attribute memory device information:
Device number 1, type Function specific, WPS = OFF
Speed = 100nS, Memory block size = 8Kb, 8 units
Tuple #4, code = 0x14 (No link), length = 0
Tuple #5, code = 0x20 (Manufacturer ID), length = 4
000: 04 01 01 00
PCMCIA ID = 0x104, OEM ID = 0x1
Tuple #6, code = 0x21 (Functional ID), length = 2
000: 02 01
Serial port/modem - POST initialize
Tuple #7, code = 0x22 (Functional EXT), length = 4
000: 00 02 0f 7f
Serial interface extension:
16550 UART, Parity - Space,Mark,Odd,Even,
Tuple #8, code = 0x15 (Version 1 info), length = 59
000: 04 01 53 6f 63 6b 65 74 20 43 6f 6d 6d 75 6e 69
010: 63 61 74 69 6f 6e 73 20 49 6e 63 00 53 65 72 69
020: 61 6c 20 50 6f 72 74 20 41 64 61 70 74 65 72 20
030: 52 65 76 69 73 69 6f 6e 20 42 00
Version = 4.1, Manuf = [Socket Communications Inc],card vers = [Serial Port Adapter Revision B]
Addit. info = [],[],[],[],[],[€],[ - ],[ ],[],[],[],[],[],[],[],[0],[]
Tuple #9, code = 0x1a (Configuration map), length = 5
000: 01 00 00 80 0f
Reg len = 2, config register addr = 0x8000, last config = 0x0
Registers: XXXX----
Tuple #10, code = 0x1b (Configuration entry), length = 19
000: c1 41 99 49 55 2d 54 23 30 ff ff 20 c1 05 43 4f
010: 4d 58 00
Config index = 0x1(default)
Interface byte = 0x41 (I/O) +RDY/-BSY active
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Continuous supply current: 2.5 x 10mA
Power down supply current: 5 x 1mA
Card decodes 3 address lines, 8 Bit I/O only
IRQ modes: Level
IRQ level = 3
Max twin cards = 0
Misc attr: (Read-only) (Power down supported)
Tuple #11, code = 0x1b (Configuration entry), length = 23
000: c3 41 99 49 55 2d 54 b0 60 f8 03 07 30 10 00 20
010: c1 05 43 4f 4d 31 00
Config index = 0x3(default)
Interface byte = 0x41 (I/O) +RDY/-BSY active
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Continuous supply current: 2.5 x 10mA
Power down supply current: 5 x 1mA
Card decodes 16 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x3f8 block length = 0x8
IRQ modes: Level
IRQs: 4 5 12
Max twin cards = 0
Misc attr: (Power down supported)
Tuple #12, code = 0x1b (Configuration entry), length = 23
000: c5 41 99 49 55 2d 54 b0 60 f8 02 07 30 08 00 20
010: c1 05 43 4f 4d 32 00
Config index = 0x5(default)
Interface byte = 0x41 (I/O) +RDY/-BSY active
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Continuous supply current: 2.5 x 10mA
Power down supply current: 5 x 1mA
Card decodes 16 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x2f8 block length = 0x8
IRQ modes: Level
IRQs: 4 5 11
Max twin cards = 0
Misc attr: (Power down supported)
Tuple #13, code = 0x1b (Configuration entry), length = 23
000: c7 41 99 49 55 2d 54 b0 60 e8 03 07 30 10 00 20
010: c1 05 43 4f 4d 33 00
Config index = 0x7(default)
Interface byte = 0x41 (I/O) +RDY/-BSY active
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Continuous supply current: 2.5 x 10mA
Power down supply current: 5 x 1mA
Card decodes 16 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x3e8 block length = 0x8
IRQ modes: Level
IRQs: 4 5 12
Max twin cards = 0
Misc attr: (Power down supported)
Tuple #14, code = 0x1b (Configuration entry), length = 23
000: c9 41 99 49 55 2d 54 b0 60 e8 02 07 30 08 00 20
010: c1 05 43 4f 4d 34 00
Config index = 0x9(default)
Interface byte = 0x41 (I/O) +RDY/-BSY active
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Continuous supply current: 2.5 x 10mA
Power down supply current: 5 x 1mA
Card decodes 16 address lines, 8 Bit I/O only
I/O address # 1: block start = 0x2e8 block length = 0x8
IRQ modes: Level
IRQs: 4 5 11
Max twin cards = 0
Misc attr: (Power down supported)
Tuple #15, code = 0x1b (Configuration entry), length = 18
000: c0 40 e1 49 55 2d 54 48 01 80 00 20 c1 04 4d 45
010: 4d 00
Config index = 0x0(default)
Interface byte = 0x40 (memory) +RDY/-BSY active
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Continuous supply current: 2.5 x 10mA
Power down supply current: 5 x 1mA
Memory descriptor 1
blk length = 0x100 card addr = 0x8000
Max twin cards = 0
Misc attr: (Power down supported)
Tuple #16, code = 0xff (Terminator), length = 0
2 slots found
==
A smooth sea never made a skillful mariner
_____________________________________________________________
Darklite.Com - Global Web Solutions at the RIGHT price.
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20000701081943.7BD43E0B5>