Date: Sat, 30 Nov 2002 16:00:16 -0700 (MST) From: Barkley Vowk <bvowk@math.ualberta.ca> To: freebsd-current@freebsd.org Subject: Hell notebook (Vaio R505TL) Message-ID: <20021130155501.N660-100000@3jane.math.ualberta.ca>
next in thread | raw e-mail | index | archive | help
I've got a notebook running current, and I've got a horde of problems I
need some help fixing...
1) ACPI lets me control fans and cpu speed nicely, and the notebook will
suspend nicely, and it almost resumes properly. When the notebook wakes up
it comes back on the network and the keyboard works properly, but the
display stays black. Suspending is the #1 concern I have right now.
When I power the system down using the power button, I cannot turn the
notebook back on until I have removed the battery (and power adapter) for
a few seconds first.
2) CardBus doesn't work. When I compile cardbus support in I see:
cbb0: Unsupported card type detected
Inserting a card into the slot causes an instant panic:
3 DiX kernel: Fatal trap 18: integer divide fault while in kernel mode
3 DiX kernel: instruction pointer = 0x8:0xc25bae04
3 DiX kernel: stack pointer = 0x10:0xcb4c5cac
3 DiX kernel: frame pointer = 0x10:0xcb4c5cc0
3 DiX kernel: code segment = base 0x0, limit 0xfffff, type 0x1b
3 DiX kernel: = DPL 0, pres 1, def32 1, gran 1
3 DiX kernel: processor eflags = interrupt enabled, IOPL = 0
3 DiX kernel: current process = 21 (irq9: cbb0 uhci0++)
In addition, while cardbus is in the kernel the fxp0 device fails to work
(which makes getting tracebacks from the notebook a pain in the ass, it
has no serial console either).
3) USB has stopped working, usb had previously been working quite well,
but in the last upgrade, usb now fails to attach any devices:
8 DiX kernel: uhub0: device problem, disabling port 2
4 DiX kernel: uhub0: device problem, disabling port 1
0 DiX kernel: uhub0: device problem, disabling port 1
0 DiX kernel: uhub0: port error, restarting port 1
I've tried 3 devices that all previously worked quite well.
I can change nothing in the bios really, I can turn plug and play on and
off and the motion logo on boot, and that about covers it.
I've attached a dmesg and acpidump. Any help would be greatly appreciated.
-- Snip Snip --
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #2: Sun Nov 24 23:37:18 MST 2002
root@DiX.evil.mil:/usr/obj/usr/src/sys/DIX
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0520000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc05200a8.
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 645877648 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (645.88-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 199753728 (190 MB)
avail memory = 188391424 (179 MB)
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <SONY U1 > on motherboard
Using $PIR table, 9 entries at 0xc00fdf30
Timecounter "ACPI-fast" frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 0.1.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 0.1.1
\\_SB_.LNKC irq 0: [ 9] low,level,sharable 0.1.2
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 0.1.3
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 0.2.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 0.31.1
\\_SB_.LNKH irq 9: [ 9] low,level,sharable 0.31.2
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 0.31.3
---- before setting priority for links ------------
\\_SB_.LNKC:
interrupts: 9
penalty: 830
references: 1
priority: 0
\\_SB_.LNKD:
interrupts: 9
penalty: 830
references: 2
priority: 0
---- before fixup boot-disabled links -------------
\\_SB_.LNKD:
interrupts: 9
penalty: 830
references: 2
priority: 1660
\\_SB_.LNKC:
interrupts: 9
penalty: 830
references: 1
priority: 830
---- after fixup boot-disabled links --------------
\\_SB_.LNKD:
interrupts: 9
penalty: 830
references: 2
priority: 1660
\\_SB_.LNKC:
interrupts: 9
penalty: 830
references: 1
priority: 830
---- arbitrated configuration ---------------------
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 0.1.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 0.1.1
\\_SB_.LNKC irq 0: [ 9] low,level,sharable 0.1.2
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 0.1.3
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 0.2.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 0.31.1
\\_SB_.LNKH irq 9: [ 9] low,level,sharable 0.31.2
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 0.31.3
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82815 (i815 GMCH) SVGA controller> mem 0xf4000000-0xf407ffff,0xf8000000-0xfbffffff irq 9 at device 2.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
---- initial configuration ------------------------
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 1.0.0
\\_SB_.LNKC irq 0: [ 9] low,level,sharable 1.2.0
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 1.2.1
\\_SB_.LNKE irq 9: [ 9] low,level,sharable 1.8.0
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 1.12.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 1.12.1
\\_SB_.LNKC irq 0: [ 9] low,level,sharable 1.12.2
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 1.12.3
---- before setting priority for links ------------
\\_SB_.LNKD:
interrupts: 9
penalty: 1670
references: 4
priority: 1660
\\_SB_.LNKC:
interrupts: 9
penalty: 1670
references: 3
priority: 830
---- before fixup boot-disabled links -------------
\\_SB_.LNKD:
interrupts: 9
penalty: 1670
references: 4
priority: 6680
\\_SB_.LNKC:
interrupts: 9
penalty: 1670
references: 3
priority: 5010
---- after fixup boot-disabled links --------------
\\_SB_.LNKD:
interrupts: 9
penalty: 1670
references: 4
priority: 6680
\\_SB_.LNKC:
interrupts: 9
penalty: 1670
references: 3
priority: 5010
---- arbitrated configuration ---------------------
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 1.0.0
\\_SB_.LNKC irq 0: [ 9] low,level,sharable 1.2.0
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 1.2.1
\\_SB_.LNKE irq 9: [ 9] low,level,sharable 1.8.0
\\_SB_.LNKA irq 9: [ 9] low,level,sharable 1.12.0
\\_SB_.LNKB irq 9: [ 9] low,level,sharable 1.12.1
\\_SB_.LNKC irq 0: [ 9] low,level,sharable 1.12.2
\\_SB_.LNKD irq 0: [ 9] low,level,sharable 1.12.3
pci1: <ACPI PCI bus> on pcib1
pci1: <serial bus, FireWire> at device 0.0 (no driver attached)
pci1: <bridge, PCI-CardBus> at device 2.0 (no driver attached)
fxp0: <Intel Pro/100 Ethernet> port 0x3000-0x303f mem 0xf4100000-0xf4100fff irq 9 at device 8.0 on pci1
fxp0: Ethernet address 08:00:46:18:21:0b
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH2 ATA100 controller> port 0x1800-0x180f at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> port 0x1820-0x183f irq 9 at device 31.2 on pci0
usb0: <Intel 82801BA/BAM (ICH2) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: Microsoft Microsoft Wheel Mouse Optical\M-., rev 1.10/1.21, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
uhci1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> port 0x2400-0x241f irq 9 at device 31.4 on pci0
usb1: <Intel 82801BA/BAM (ICH2) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
umass0: Sony USB Memory Stick Slot, rev 1.10/1.80, addr 2
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms> at device 31.6 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
acpi_acad0: <AC adapter> on acpi0
orm0: <Option ROMs> at iomem 0xdc000-0xdffff,0xd8000-0xdbfff,0xc0000-0xcbfff on isa0
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 10.000 msec
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.29 initialized. Default = pass all, Logging = enabled
acpi_cpu: CPU throttling enabled, 8 steps from 100% to 12.5%
system power profile changed to 'economy'
ad0: 19077MB <TOSHIBA MK2017GAP> [38760/16/63] at ata0-master UDMA100
(probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI Status: Check Condition
(probe0:umass-sim0:0:0:0): UNIT ATTENTION asc:29,0
(probe0:umass-sim0:0:0:0): Power on, reset, or bus device reset occurred
(probe0:umass-sim0:0:0:0): Retrying Command (per Sense Data)
(probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0
(probe0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(probe0:umass-sim0:0:0:0): SCSI Status: Check Condition
(probe0:umass-sim0:0:0:0): NOT READY asc:3a,0
(probe0:umass-sim0:0:0:0): Medium not present
(probe0:umass-sim0:0:0:0): Unretryable error
Mounting root from ufs:/dev/ad0s1a
WARNING: / was not properly dismounted
WARNING: /home was not properly dismounted
WARNING: /tmp was not properly dismounted
WARNING: /usr was not properly dismounted
WARNING: /var was not properly dismounted
/var: mount pending error: blocks 4 files 2
ums0: at uhub0 port 1 (addr 2) disconnected
ums0: detached
uhub0: device problem, disabling port 2
uhub0: device problem, disabling port 1
--Snip Snip--
--Snip Snip--
8 DiX kernel: cbb0: <RF5C475 PCI-CardBus Bridge> at device 2.0 on pci1
8 DiX kernel: cardbus0: <CardBus bus> on cbb0
8 DiX kernel: pccard0: <16-bit PCCard bus> on cbb0
8 DiX kernel: pcib1: possible interrupts: 9
8 DiX kernel: pcib1: slot 2 INTA routed to irq 9 via \_SB_.LNKC
8 DiX kernel: fxp0: <Intel Pro/100 Ethernet> port 0x3000-0x303f mem
0xf4100000-0xf4100fff irq 9 at device 8.0 on pci1
8 DiX kernel: fxp0: could not map device registers
8 DiX kernel: device_probe_and_attach: fxp0 attach returned 6
8 DiX kernel: cbb0: Unsupported card type detected
--Snip Snip--
-----------------------------------------------------------
Barkley C. Vowk -- Systems Analyst -- University of Alberta
Math Sciences Department - Barkley.Vowk@math.ualberta.ca
Office: CAB642A, 780-492-4064
Opinions expressed are the responsibility of the author and
may not reflect the opinions of others or reality.
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20021130155501.N660-100000>