Date: Mon, 19 Apr 2004 10:04:26 +0100 From: Francisco Alves Cabrita <francisco@nortenet.pt> To: imp@bsdimp.com Cc: freebsd-current@freebsd.org Subject: Re: Cardbus problem [SOLVED] Message-ID: <1082365434.876.2.camel@zarcon.homeunix.net> In-Reply-To: <20040418190111.6196B16A4D0@hub.freebsd.org> References: <20040418190111.6196B16A4D0@hub.freebsd.org>
next in thread | previous in thread | raw e-mail | index | archive | help
> > In message: <1082226317.834.12.camel@zarcon.homeunix.net> > > Francisco Alves Cabrita <francisco@nortenet.pt> writes: > > : hello > > : i'm running (i386)5-CURRENT and in this "nightly" buildwold ,, my > > : cardbus (ethernet pcmcia ovislink chipset rl) didnt get enabled"" > > : > > : > > : this was the message during boot: > > : > > : cbb0: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.0 on pci0 > > : cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0 > > : cardbus0: <CardBus bus> on cbb0 > > : pccard0: <16-bit PCCard bus> on cbb0 > > : cbb0: bad Vcc request. ctrl=0xf000ef08, status=0xf000e2c3 > > : cbb_power: 0V > > : cbb1: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.1 on pci0 > > : cbb1: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0x1000 > > : cardbus1: <CardBus bus> on cbb1 > > : pccard1: <16-bit PCCard bus> on cbb1 > > : cbb1: bad Vcc request. ctrl=0x7720700, status=0x76f076c > > : cbb_power: 0V > > : > > : can some one give a tip !!! > > > > Please submit an older, working dmesg. I think I know what's going > > on, but w/o that, I can't be sure. > > > > Since the cbb is on pci0, I think that you might have an non-ACPI > > system. Especially since the ToPIC95B is a relatively old chip. My > > guess is that this is a 100-166MHz Pentium system. > > > > Warner > > Hellow Warner, thank for you response. > > Yes, you are almost right, is not an 100-166 Pentium , but and Toshiba > (4300 series) Laptop 600Mhz with ACPI disabled for performence reasons, > but here goes the boot message when was working: > > cbb0: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.0 on pci0 > cardbus0: <CardBus bus> on cbb0 > pccard0: <16-bit PCCard bus> on cbb0 > cbb1: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.1 on pci0 > cardbus1: <CardBus bus> on cbb1 > pccard1: <16-bit PCCard bus> on cbb1 > > and the result: > > rl0: <RealTek 8139 10/100BaseTX> port 0x1000-0x10ff mem > 0x88002000-0x880021ff irq 11 at device 0.0 on cardbus1 > miibus0: <MII bus> on rl0 > rlphy0: <RealTek internal media interface> on miibus0 > rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > rl0: Ethernet address: 00:10:60:75:66:fc > rl0: [GIANT-LOCKED] > > since I installed 5.X here, i disabled the ACPI module, and didnt have > any hardware problems until now, but i will tunr it on to see what > appen. > yep, as you said,, I enabled acpi module under loader.conf and it's working fine. Thanks Warner
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1082365434.876.2.camel>