Date: Wed, 10 Sep 1997 16:28:36 -0500 (EST) From: "Jay M. Richmond" <jayrich@room101.sysc.com> To: John Dowdal <jdowdal@destiny.erols.com> Cc: freebsd-bugs@freebsd.org, freebsd-hackers@freebsd.org Subject: Re: mount cdrom returns "input/output error" Message-ID: <Pine.BSF.3.96.970910162630.1662A-100000@room101.sysc.com> In-Reply-To: <Pine.BSF.3.95q.970910172201.6892A-100000@destiny.erols.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Whew... In a way I'm glad that I'm not the only one :).. Yes I did cvsup to 2.2-STABLE around that time as well. I'm using a Mitsumi 8x, but I assume it's the same... is that a SCSI cd-writer? if so, we may have differnt problems. I've cc'ed this to freebsd-bugs and freebsd-hackers. If you need any other info (please check through the rest of the quoted material), pleaese let me know... Thanks, Jay On Wed, 10 Sep 1997, John Dowdal wrote: > > I get the same error on a cvsup'd stable, downloaded around 9-1-97. I can > not "mount -o ro -t cd9660 /dev/worm0c /mnt" without getting a IO error. > I used to be able to mount this, using the same kernel config. The drive > is a HP 4020i CD writer. It is possible for me to do dd if=/dev/rworm0 > of=/dev/null bs=32k and read the whole CD; don't know if I can write cd's > or not with this version because I haven't tried. > > John > > On Wed, 10 Sep 1997, Jay M. Richmond wrote: > > > Please note: since I posted this I've also tried putting the CD-ROM on the > > primary controller and configuring it as a slave... same result. > > > > Thanks again for your time, > > Jay > > jayrich@sysc.com > > > > On Wed, 10 Sep 1997, Charlie ROOT wrote: > > > > > Hello-- > > > > > > I searched the FAQ and handbook for an answer to this before asking, but I > > > still apologize in advance if this is a "stupid question." > > > > > > Here's the situation... > > > > > > Ever since I upgraded to 2.2-STABLE, I am unable to mount any CD-ROM's > > > that I have (I tested this by going back to the 2.2.2-RELEASE kernel and > > > the CD-ROM worked great, unfortunately, I need 2.2-STABLE for some other > > > fixes.) I am sure the CD-ROM is working fine and the CD is OK. > > > > > > When I mount the CD, it says: > > > > > > # mount -t cd9660 /dev/wcd0a /cdrom > > > cd9660: /dev/wcd0a: Input/output error > > > > > > The drive is on the second IDE channel as a SLAVE, without a master (this > > > worked fine before with 2.2.2-RELEASE, has there been a change?). > > > > > > I also double checked my source configuration files as well: > > > > > > controller wdc1 at isa? port "IO_WD2" bio irq 15 vector wdintr > > > disk wd2 at wdc1 drive 0 > > > disk wd3 at wdc1 drive 1 > > > > > > options ATAPI > > > options ATAPI_STATIC > > > device wcd0 > > > > > > I also have it set up for the primary controller. This is the same > > > configuration that was in GENERIC for 2.2.2-RELEASE on my system. > > > > > > The drive is detected on boot up too: > > > > > > /kernel: wdc1: unit 1 (atapi): <FX801S/X01>, removable, intr, dma, iordis > > > > > > I've also searched the mailing list archives, and most of the time the > > > error is due to the device not being recognized or a CD not being in the > > > drive, etc. However, none of that applies here. > > > > > > My question is: is there something in 2.2-STABLE that's changed that I > > > would need to make other changes to my OS to make the CD work? > > > > > > I don't subscribe to the freebsd-questions or freebsd-stable mailing > > > lists, so please send a copy of your reponse to me via e-mail. > > > > > > Thank you very much for your time, > > > > > > Jay > > > jayrich@sysc.com > > > > > > > >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Pine.BSF.3.96.970910162630.1662A-100000>