Date: Fri, 24 Mar 2000 11:49:42 -0800 (PST) From: Thomas Geocaris <tom@geocaris.com> To: freebsd-questions@freebsd.org Subject: FreeBSD 4.0 SMP problem Message-ID: <200003241949.LAA02317@geocaris.com>
next in thread | raw e-mail | index | archive | help
Hello,
My name is Tom and I just put together a Dual 550MHZ pentium system
running FreeBSD 4.0. I am using a SuperMicro P6DGU mother board.
The system is up and running, but while running the SMP kernel I have been
having an intermittent problem with the Ethernet card. I have a 3com 3C905C
10/100 NIC. The Ethernet card (or kernel) seems to not respond after the system
goes into standby mode and returns. When I ping from the machine out, the
kernel starts generating "watchdog timeouts".
There is no problem with the GENERIC kernel. As a side note: If I compile in
the "apm0" driver into the SMP kernel and run "apm -e enable", the machine
will imediately reboot. Again, the GENERIC kernel is fine.
I have search the archives and can't find a previous solution.
I have included the "mptable" and "dmesg" below for the GENERIC and SMP
kernel. (I get a "HOSED" message while running mptable on the extension).
If anybody can help I would be very thankful.
Thanks, Tom (tom@geocaris.com)
######################## SMP mptable ##########################################
===============================================================================
MPTable, version 2.0.15
-------------------------------------------------------------------------------
MP Floating Pointer Structure:
location: BIOS
physical address: 0x000fb4f0
signature: '_MP_'
length: 16 bytes
version: 1.4
checksum: 0x2d
mode: Virtual Wire
-------------------------------------------------------------------------------
MP Config Table Header:
physical address: 0x000f2440
signature: 'PCMP'
base table length: 268
version: 1.4
checksum: 0x40
OEM ID: 'INTEL '
Product ID: '440BX '
OEM table pointer: 0x00000000
OEM table size: 0
entry count: 25
local APIC address: 0xfee00000
extended table length: 16
extended table checksum: 234
-------------------------------------------------------------------------------
MP Config Base Table Entries:
--
Processors: APIC ID Version State Family Model Step Flags
0 0x11 BSP, usable 6 7 3 0x387fbff
1 0x11 AP, usable 6 7 3 0x387fbff
--
Bus: Bus ID Type
0 PCI
1 PCI
2 ISA
--
I/O APICs: APIC ID Version State Address
2 0x11 usable 0xfec00000
--
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT conforms conforms 2 0 2 0
INT conforms conforms 2 1 2 1
INT conforms conforms 2 0 2 2
INT conforms conforms 2 3 2 3
INT conforms conforms 2 4 2 4
INT conforms conforms 2 6 2 6
INT conforms conforms 2 7 2 7
INT active-hi edge 2 8 2 8
INT conforms conforms 2 12 2 12
INT conforms conforms 2 13 2 13
INT conforms conforms 2 14 2 14
INT conforms conforms 2 15 2 15
INT active-lo level 2 10 2 16
INT active-lo level 2 11 2 17
INT active-lo level 2 9 2 18
INT active-lo level 2 5 2 19
SMI conforms conforms 2 0 2 23
--
Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT conforms conforms 0 0:A 255 0
NMI conforms conforms 0 0:A 255 1
-------------------------------------------------------------------------------
MP Config Extended Table Entries:
Extended Table HOSED!
######################## SMP dmesg ##########################################
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-RELEASE #13: Fri Mar 24 00:15:59 PST 2000
tom@three.geocaris.com:/usr/src/sys/compile/THREE
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon (551.25-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x673 Stepping = 3
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,XMM>
real memory = 268435456 (262144K bytes)
avail memory = 256679936 (250664K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
IOAPIC #0 intpin 16 -> irq 10
IOAPIC #0 intpin 17 -> irq 11
IOAPIC #0 intpin 18 -> irq 9
IOAPIC #0 intpin 19 -> irq 5
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000
cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc039d000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc039d09c.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443GX host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib2: <Intel 82443GX (440 GX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib2
pci1: <3Dfx Voodoo 3 graphics accelerator> at 0.0 irq 11
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xffa0-0xffaf at device 7.1 on pci0
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 7.2
Timecounter "PIIX" frequency 3579545 Hz
chip1: <Intel 82371AB Power management controller> port 0x440-0x44f at device 7.3 on pci0
ahc0: <Adaptec aic7890/91 Ultra2 SCSI adapter> port 0xe800-0xe8ff mem 0xfebff000-0xfebfffff irq 10 at device 14.0 on pci0
ahc0: aic7890/91 Wide Channel A, SCSI Id=7, 16/255 SCBs
pcm0: <AudioPCI ES1371> port 0xef00-0xef3f irq 9 at device 18.0 on pci0
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xec00-0xec7f mem 0xfebfef80-0xfebfefff irq 5 at device 20.0 on pci0
xl0: Ethernet address: 00:01:02:33:ba:a6
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: supplying EUI64: 00:01:02:ff:fe:33:ba:a6
pcib1: <Intel 82443GX host to AGP bridge> on motherboard
pci2: <PCI bus> on pcib1
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model ThinkingMouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
SMP: AP CPU #1 Launched!
acd0: CDROM <NEC CD-ROM DRIVE:28B> at ata1-slave using PIO4
Waiting 15 seconds for SCSI devices to settle
Mounting root from ufs:/dev/da0s1a
da0 at ahc0 bus 0 target 0 lun 0
da0: <WDIGTL WD183 ULTRA2 1.00> Fixed Direct Access SCSI-2 device
da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled
da0: 17461MB (35761710 512 byte sectors: 255H 63S/T 2226C)
xl0: starting DAD for fe80:0001::0201:02ff:fe33:baa6
xl0: DAD complete for fe80:0001::0201:02ff:fe33:baa6 - no duplicates found
######################## GENERIC mptable #######################################
===============================================================================
MPTable, version 2.0.15
-------------------------------------------------------------------------------
MP Floating Pointer Structure:
location: BIOS
physical address: 0x000fb4f0
signature: '_MP_'
length: 16 bytes
version: 1.4
checksum: 0x2d
mode: Virtual Wire
-------------------------------------------------------------------------------
MP Config Table Header:
physical address: 0x000f2440
signature: 'PCMP'
base table length: 268
version: 1.4
checksum: 0x40
OEM ID: 'INTEL '
Product ID: '440BX '
OEM table pointer: 0x00000000
OEM table size: 0
entry count: 25
local APIC address: 0xfee00000
extended table length: 16
extended table checksum: 234
-------------------------------------------------------------------------------
MP Config Base Table Entries:
--
Processors: APIC ID Version State Family Model Step Flags
0 0x11 BSP, usable 6 7 3 0x387fbff
1 0x11 AP, usable 6 7 3 0x387fbff
--
Bus: Bus ID Type
0 PCI
1 PCI
2 ISA
--
I/O APICs: APIC ID Version State Address
2 0x11 usable 0xfec00000
--
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT conforms conforms 2 0 2 0
INT conforms conforms 2 1 2 1
INT conforms conforms 2 0 2 2
INT conforms conforms 2 3 2 3
INT conforms conforms 2 4 2 4
INT conforms conforms 2 6 2 6
INT conforms conforms 2 7 2 7
INT active-hi edge 2 8 2 8
INT conforms conforms 2 12 2 12
INT conforms conforms 2 13 2 13
INT conforms conforms 2 14 2 14
INT conforms conforms 2 15 2 15
INT active-lo level 2 10 2 16
INT active-lo level 2 11 2 17
INT active-lo level 2 9 2 18
INT active-lo level 2 5 2 19
SMI conforms conforms 2 0 2 23
--
Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT conforms conforms 0 0:A 255 0
NMI conforms conforms 0 0:A 255 1
-------------------------------------------------------------------------------
MP Config Extended Table Entries:
Extended Table HOSED!
######################## GENERIC dmesg #######################################
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-RELEASE #0: Mon Mar 20 22:50:22 GMT 2000
root@monster.cdrom.com:/usr/src/sys/compile/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon (551.25-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x673 Stepping = 3
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,XMM>
real memory = 268435456 (262144K bytes)
avail memory = 256544768 (250532K bytes)
Preloaded elf kernel "kernel.GENERIC" at 0xc03c0000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443GX host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib2: <Intel 82443GX (440 GX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib2
pci1: <3Dfx Voodoo 3 graphics accelerator> at 0.0 irq 11
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xffa0-0xffaf at device 7.1 on pci0
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 7.2
chip1: <Intel 82371AB Power management controller> port 0x440-0x44f at device 7.3 on pci0
ahc0: <Adaptec aic7890/91 Ultra2 SCSI adapter> port 0xe800-0xe8ff mem 0xfebff000-0xfebfffff irq 10 at device 14.0 on pci0
ahc0: aic7890/91 Wide Channel A, SCSI Id=7, 16/255 SCBs
pci0: <unknown card> (vendor=0x1274, dev=0x1371) at 18.0 irq 9
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xec00-0xec7f mem 0xfebfef80-0xfebfefff irq 5 at device 20.0 on pci0
xl0: Ethernet address: 00:01:02:33:ba:a6
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: supplying EUI64: 00:01:02:ff:fe:33:ba:a6
pcib1: <Intel 82443GX host to AGP bridge> on motherboard
pci2: <PCI bus> on pcib1
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model ThinkingMouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
acd0: CDROM <NEC CD-ROM DRIVE:28B> at ata1-slave using PIO4
Waiting 15 seconds for SCSI devices to settle
Mounting root from ufs:/dev/da0s1a
da0 at ahc0 bus 0 target 0 lun 0
da0: <WDIGTL WD183 ULTRA2 1.00> Fixed Direct Access SCSI-2 device
da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled
da0: 17461MB (35761710 512 byte sectors: 255H 63S/T 2226C)
xl0: starting DAD for fe80:0001::0201:02ff:fe33:baa6
xl0: DAD complete for fe80:0001::0201:02ff:fe33:baa6 - no duplicates found
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200003241949.LAA02317>