Date: Fri, 6 Jun 2014 00:22:20 +0000 (UTC) From: Allan Jude <allanjude@FreeBSD.org> To: src-committers@freebsd.org, svn-src-all@freebsd.org, svn-src-head@freebsd.org Subject: svn commit: r267141 - head/sbin/ifconfig Message-ID: <201406060022.s560MKbi077617@svn.freebsd.org>
next in thread | raw e-mail | index | archive | help
Author: allanjude (doc committer) Date: Fri Jun 6 00:22:19 2014 New Revision: 267141 URL: http://svnweb.freebsd.org/changeset/base/267141 Log: Style cleanups on ifconfig.8 fix igor warnings uppercase all instances of Ethernet replace bad e.g. CR: D91 Approved by: wblock (mentor) Modified: head/sbin/ifconfig/ifconfig.8 Modified: head/sbin/ifconfig/ifconfig.8 ============================================================================== --- head/sbin/ifconfig/ifconfig.8 Fri Jun 6 00:20:54 2014 (r267140) +++ head/sbin/ifconfig/ifconfig.8 Fri Jun 6 00:22:19 2014 (r267141) @@ -28,7 +28,7 @@ .\" From: @(#)ifconfig.8 8.3 (Berkeley) 1/5/94 .\" $FreeBSD$ .\" -.Dd October 21, 2013 +.Dd June 5, 2014 .Dt IFCONFIG 8 .Os .Sh NAME @@ -141,13 +141,13 @@ The link-level .Pq Dq link address is specified as a series of colon-separated hex digits. -This can be used to -e.g.,\& set a new MAC address on an ethernet interface, though the -mechanism used is not ethernet-specific. +This can be used to, for example, +set a new MAC address on an Ethernet interface, though the +mechanism used is not Ethernet specific. If the interface is already up when this option is used, it will be briefly brought down and then brought back up again in order to ensure that the receive -filter in the underlying ethernet hardware is properly reprogrammed. +filter in the underlying Ethernet hardware is properly reprogrammed. .It Ar address_family Specify the address family @@ -179,7 +179,7 @@ or .Dq lladdr . Specifying .Fl l Dq ether -will list only ethernet interfaces, excluding all other interface types, +will list only Ethernet interfaces, excluding all other interface types, including the loopback interface. .It Ar dest_address Specify the address of the correspondent on the other end @@ -661,7 +661,8 @@ Clear a flag .Cm defaultif . .It Cm ifdisabled Set a flag to disable all of IPv6 network communications on the -specified interface. Note that if there are already configured IPv6 +specified interface. +Note that if there are already configured IPv6 addresses on that interface, all of them are marked as .Dq tentative and DAD will be performed when this flag is cleared. @@ -1087,7 +1088,8 @@ specifies the number of beacon intervals and must be in the range 1 to 15. By default DTIM is 1 (i.e., DTIM occurs at each beacon). .It Cm quiet -Enable the use of quiet IE. Hostap will use this to silence other +Enable the use of quiet IE. +Hostap will use this to silence other stations to reduce interference for radar detection when operating on 5GHz frequency and doth support is enabled. Use @@ -1102,9 +1104,11 @@ scheduled quiet intervals defined by Qui Set the QUIET .Ar count to the number of TBTTs until the beacon interval during which the -next quiet interval shall start. A value of 1 indicates the quiet +next quiet interval shall start. +A value of 1 indicates the quiet interval will start during the beacon interval starting at the next -TBTT. A value 0 is reserved. +TBTT. +A value 0 is reserved. .It Cm quiet_offset Ar offset Set the QUIET .Ar offset @@ -2354,7 +2358,8 @@ Another name for the parameter. .It Cm accept_rev_ethip_ver Set a flag to accept both correct EtherIP packets and ones -with reversed version field. Enabled by default. +with reversed version field. +Enabled by default. This is for backward compatibility with .Fx 6.1 , 6.2, 6.3, 7.0, and 7.1. @@ -2363,7 +2368,8 @@ Clear a flag .Cm accept_rev_ethip_ver . .It Cm send_rev_ethip_ver Set a flag to send EtherIP packets with reversed version -field intentionally. Disabled by default. +field intentionally. +Disabled by default. This is for backward compatibility with .Fx 6.1 , 6.2, 6.3, 7.0, and 7.1. @@ -2446,7 +2452,7 @@ pseudo-interface. The .Xr vlan 4 interface is assigned a -copy of the parent interface's flags and the parent's ethernet address. +copy of the parent interface's flags and the parent's Ethernet address. The .Cm vlandev and @@ -2570,7 +2576,7 @@ If an .Ar address_family is specified, only interfaces of that type will be listed. .Fl l Dq ether -will list only ethernet adapters, excluding the loopback interface. +will list only Ethernet adapters, excluding the loopback interface. Use of this flag is mutually exclusive with all other flags and commands, except for .Fl d
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?201406060022.s560MKbi077617>