Date: Fri, 25 Aug 2000 13:07:59 -0500 From: "Alejandro Ramirez" <ales@megacable.com.mx> To: <sos@freebsd.dk> Cc: <freebsd-questions@FreeBSD.ORG> Subject: ATA driver panics in Sysinstall with IBM Netfinity 5000 Servers !!! Message-ID: <0c5d01c00ebf$67b60b60$02c134c8@megared.net.mx>
next in thread | raw e-mail | index | archive | help
Hi Soren,
I have two IBM Netfinity 5000 Dual PIII 600Mhz servers that wanted to
install FreeBSD 4.1-RELEASE on them, when I booted from the cdrom to start
the installation, the cdrom probe failed, it gave me the following errors:
(null): MODE_SENSE_BIG command timeout - resetting
ata0: resetting devices .. done
(null): read data overrun 28/2
acd0: CDROM <CRD-8322B> at ata0-master using PIO4
Then I got the install screen, when it says "Probing devices, please wait
(this can take a while) ...", and got stalled for about 30 seconds in there,
then gave me the options screen, I switched to the debug screen (CTRL+F2),
and it had this messages:
DEBUG: ioctl(3, TIOCCONS, NULL) = 0 (success)
DEBUG: Canīt open PC-card controller /dev/card0
acd0: READ_TOC command timeout - resetting
ata0: resetting devices .. done
acd0: read data overrun 12/0
DEBUG: Add mapping for /dev/cuaa0 to sl0
DEBUG: Add mapping for /dev/cuaa1 to sl0
Then I switched back to the installation screen (CTRL+F1) I configured the
disks, distro, etc, and after the partitioning finished, gave me the
following error & panic on the debug screen (CTRL+F2) :
...
...
...
/mnt/etc/protocols
/mnt/etc/services
44 blocks
DEBUG: Generating /etc/fstab file
acd0: READ_TOC command timeout - resetting
ata0: resetting devices .. done
acd0: read data overrun 12/0
acd0: READ_BIG command timeout - resetting
ata0: resetting devices .. done
Fatal trap 12: page fault while in kernel mode
fault virtual address = 0xc24a2000
fault code = supervisor write, page not present
instructor pointer = 0x8:0xc02940ee
stack pointer = 0x10:0xc03218f0
frame pointer = 0x10:0xc0321900
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = idle
interrupt mask = bio
trap number = 12
I could never pass this stage, I also thinked that the cdrom disk was
the faulty one, I downloaded again the iso image & created 2 more cdrom
disks, and the same happened with both of them, I had to boot from from
floppies, mount the freebsd cdrom in another server, and choose the install
media to ftp, thats the way I worked arround this.
Actually the BIOS report this unit as PIO3 but the ata driver reports it
like PIO4, could this be the problem???
Below is the dmesg output of this server:
P.S. If I can help you whit something just tell me, I can give you root
access to this server, because its not in production yet.
Thanks...
Ales
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1-RELEASE #0: Fri Jul 28 14:30:31 GMT 2000
jkh@ref4.freebsd.org:/usr/src/sys/compile/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (598.40-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x673 Stepping =3
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,
CMOV,PAT,PSE36,MMX,FXSR,XMM>
real memory = 671072256 (655344K bytes)
avail memory = 647876608 (632692K bytes)
Preloaded elf kernel "kernel" at 0xc040d000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
ahc0: <Adaptec aic7895 Ultra SCSI adapter> port 0x2000-0x20ff mem
0xfebff000-0xfebfffff irq 11 at device 6.0 on pci0
ahc0: aic7895 Wide Channel A, SCSI Id=7, 16/255 SCBs
ahc1: <Adaptec aic7895 Ultra SCSI adapter> port 0x2200-0x22ff mem
0xfebfe000-0xfebfefff irq 15 at device 6.1 on pci0
ahc1: aic7895 Wide Channel B, SCSI Id=7, 16/255 SCBs
lnc0: <PCNet/PCI Ethernet adapter> port 0x2180-0x219f mem
0xfebfdc00-0xfebfdc1f irq 10 at device 9.0 on pci0
lnc0: PCnet-FAST+ address 00:06:29:50:fe:37
lnc0: driver is using old-style compatability shims
pci0: <S3 Trio 64V2/DX/GX graphics accelerator>at 10.0 irq 9
isab0: <PCI to ISA bridge (vendor=1166 device=0200)> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Generic PCI ATA controller> port
0xffa0-0xffaf,0-0x3,0-0x7,0x3f4-0x3f7,0x1f0-0x1f7 irq 14 at device 15.1 on
pci0
ata0: at 0x1f0 irq 14 on atapci0
ohci0: <OHCI (generic) USB controller> mem 0xff700000-0xff700fff irq 10 at
device 15.2 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (unknown) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pcib1: <RCC HE host to PCI bridge> on motherboard
pci1: <PCI bus> on pcib1
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa 0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
(null): MODE_SENSE_BIG command timeout - resetting
ata0: resetting devices .. done
(null): read data overrun 28/2
acd0: CDROM <CRD-8322B> at ata0-master using PIO4
Waiting 15 seconds for SCSI devices to settle
sa0 at ahc1 bus 0 target 6 lun 0
sa0: <ARCHIVE Python 04106-XXX 735E> Removable Sequential Access SCSI-2
device
sa0: 5.000MB/s transfers (5.000MHz, offset 15)
pass5 at ahc1 bus 0 target 14 lun 0
pass5: <SDR GEM200 2> Fixed Processor SCSI-2 device
pass5: 3.300MB/s transfers
da0 at ahc1 bus 0 target 0 lun 0
da0: <IBM-PSG ST39103LC !# B222> Fixed Direct Access SCSI-2 device
da0: 11.626MB/s transfers (5.813MHz, offset 8, 16bit), Tagged Queueing
Enabled
da0: 8678MB (17774160 512 byte sectors: 255H 63S/T 1106C)
da2 at ahc1 bus 0 target 2 lun 0
da2: <IBM-PSG ST39103LC !# B222> Fixed Direct Access SCSI-2 device
da2: 11.626MB/s transfers (5.813MHz, offset 8, 16bit), Tagged Queueing
Enabled
da2: 8678MB (17774160 512 byte sectors: 255H 63S/T 1106C)
da3 at ahc1 bus 0 target 3 lun 0
da3: <IBM-PSG ST39103LC !# B222> Fixed Direct Access SCSI-2 device
da3: 11.626MB/s transfers (5.813MHz, offset 8, 16bit), Tagged Queueing
Enabled
da3: 8678MB (17774160 512 byte sectors: 255H 63S/T 1106C)
da1 at ahc1 bus 0 target 1 lun 0
da1: <IBM-PSG ST39103LC !# B222> Fixed Direct Access SCSI-2 device
da1: 11.626MB/s transfers (5.813MHz, offset 8, 16bit), Tagged Queueing
Enabled
da1: 8678MB (17774160 512 byte sectors: 255H 63S/T 1106C)
Mounting root from ufs:/dev/da0s1a
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?0c5d01c00ebf$67b60b60$02c134c8>