Date: Fri, 15 Dec 2000 21:41:45 +0800 From: "tanbin" <tanbin@empworld.com> To: <freebsd-questions@FreeBSD.ORG> Cc: <otter@otter.cc>, <dylan@dragnet.com.au> Subject: adding ide to a scsi FreeBSD 4.0 Message-ID: <01ae01c0669c$c5522440$0b00000a@yourtender.com>
next in thread | raw e-mail | index | archive | help
someone once asked how to add an ide disk to a freebsd system installed on a
scsi. i am using FreeBSD 4.0 but i could not see 'ad0' or 'wd0' in dmesg.
i suspect i need to add ide-probing in the kernel. now the boot simply can't
detect the ide.
my bios could detect the new Quantum Fireball ide disk (as shown on screen
after the mem test). i have tried both IDE1 and IDE2 ports. i finally
settled on IDE1. on IDE1 there are 2 devices: primary master is a cd rom
drive, and primary slave is the Quantum Fireball ide disk.
everything in the original message attached applies to me.
> Are there any issues involved in using a combination of SCSI and IDE
> drives ?
>
> I want to mount an IDE drive with a BSD ufs in a system booted from a
> SCSI drive.
>
> If I play with Bios I can change which drive it boots too but when I
> boot into the system on the SCSI drive the IDE drive
> does not show up in dmesg.boot and is unmountable.
---------- here is my dmesg.boot ---------
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-RELEASE #0: Thu Nov 16 04:43:12 GMT 2000
tanbin@camel.yourtender.com:/usr/src/sys/compile/IPMSQ
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon (499.15-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x672 Stepping = 2
Features=0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,
PAT,PSE36,PN,MMX,FXSR,XMM>
real memory = 67043328 (65472K bytes)
avail memory = 61087744 (59656K bytes)
Preloaded elf kernel "kernel" at 0xc03c3000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <ATI Mach64-GZ graphics accelerator> at 0.0
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 7.1 on
pci0
ata0: at 0x1f0 irq 14 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 7.2 irq 11
chip1: <Intel 82371AB Power management controller> port 0x5000-0x500f at
device 7.3 on pci0
rl0: <RealTek 8139 10/100BaseTX> port 0xe400-0xe4ff mem
0xe9000000-0xe90000ff irq 10 at device 9.0 on pci0
rl0: Ethernet address: 00:50:ba:d2:fa:28
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: supplying EUI64: 00:50:ba:ff:fe:d2:fa:28
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xe800-0xe87f mem
0xe9002000-0xe900207f irq 11 at device 11.0 on pci0
xl0: Ethernet address: 00:50:da:75:22:76
miibus1: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus1
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ahc0: <Adaptec aic7890/91 Ultra2 SCSI adapter> port 0xec00-0xecff mem
0xe9001000-0xe9001fff irq 5 at device 12.0 on pci0
ahc0: aic7890/91 Wide Channel A, SCSI Id=7, 16/255 SCBs
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
IP packet filtering initialized, divert enabled, rule-based forwarding
disabled, default to deny, logging disabled
acd0: CDROM <SONY CD-ROM CDU4821> at ata0-master using PIO4
Waiting 15 seconds for SCSI devices to settle
Mounting root from ufs:/dev/da0s1a
da0 at ahc0 bus 0 target 6 lun 0
da0: <QUANTUM ATLAS 10K 9WLS UC81> Fixed Direct Access SCSI-3 device
da0: 11.626MB/s transfers (5.813MHz, offset 31, 16bit), Tagged Queueing
Enabled
da0: 8759MB (17938986 512 byte sectors: 255H 63S/T 1116C)
________________________ end ___________
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?01ae01c0669c$c5522440$0b00000a>