Date: Wed, 11 Jun 2008 21:12:46 -0700 From: "Hidetoshi Shimokawa" <simokawa@FreeBSD.ORG> To: "Sean Bruno" <sbruno@miralink.com> Cc: freebsd-firewire@freebsd.org Subject: Re: 400/800 card Message-ID: <626eb4530806112112w4b3873c6n195385af3db909cc@mail.gmail.com> In-Reply-To: <485011B7.7060900@miralink.com> References: <485011B7.7060900@miralink.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Wed, Jun 11, 2008 at 10:56 AM, Sean Bruno <sbruno@miralink.com> wrote: > I have a 400/800 card installed in my RELENG_7 box that has one 800 > connector and two 400 connectors on it. Looking over the system, I wonder > if the card is working correctly when I attach a S400 device to it: > > [sean@home-test ~]$ sudo fwcontrol -t > crc_len: 3 generation:1 node_count:1 sid_count:1 > id link gap_cnt speed delay cIRM power port0 port1 port2 ini more > 00 1 63 S800 0 1 -1W - - - 1 0 The phy layer doesn't seem to recognize the S400 device. It seem to be a hardware problem. Are your cable and connector o.k.? Did a bus reset occur when you attached the device? > [sean@home-test ~]$ sudo fwcontrol 1 devices (info_len=1) > node EUI64 status > 0 00-13-3b-01-00-01-01-82 0 > > [sean@home-test ~]$ sudo fwcontrol -c 0 > first quad: 0x044cbb31 info_len=4 crc_len=76 crc=0xbb31(OK) > bus_name: 0x31333934 > irmc:1 cmc:1 isc:1 bmc:1 pmc:0 > cyc_clk_acc:100 max_rec:11 max_rom:0 > generation:2 link_spd:3 > EUI64: 00-13-3b-01-00-01-01-82 > root_directory: len=0x0008(8) crc=0x2aa1(OK) > 0c(I:0c) 0083c0 node_capabilities: > 03(I:03) acde48 module_vendor_ID: > 81(L:01) 000006 text_leaf: len=7 crc=0x82ed(OK) FreeBSD Project > 04(I:04) 0aae97 hardware_version: > 81(L:01) 00000c text_leaf: len=3 crc=0x0000(OK) > d1(D:11) 00000f unit_directory: len=8 crc=0x9735(OK) > 12(I:12) acde48 unit_spec_ID: > 81(L:01) 000007 text_leaf: len=5 crc=0xec03(OK) FreeBSD > 13(I:13) 64636f unit_sw_version: > 81(L:01) 00000b text_leaf: len=5 crc=0xc6ec(OK) dcons > 3a(I:3a) 000001 unit_characteristics: > 3b(I:3b) 388000 command_set_revision: > 3c(I:3c) 000000 firmware_revision: > 3d(I:3d) c00240 reconnect_timeout: > d1(D:11) 000023 unit_directory: len=4 crc=0xbb7c(OK) > 12(I:12) 00005e unit_spec_ID: > 81(L:01) 000003 text_leaf: len=4 crc=0x9bde(OK) IANA > 13(I:13) 000001 unit_sw_version: > 81(L:01) 000006 text_leaf: len=4 crc=0x08db(OK) IPv4 > d1(D:11) 000031 unit_directory: len=4 crc=0x55ae(OK) > 12(I:12) 00005e unit_spec_ID: > 81(L:01) 000003 text_leaf: len=4 crc=0x9bde(OK) IANA > 13(I:13) 000002 unit_sw_version: > 81(L:01) 000006 text_leaf: len=4 crc=0x4c58(OK) IPv6 > > > fwohci0@pci0:2:1:0: class=0x0c0010 card=0x00051592 chip=0x8025104c > rev=0x01 hdr=0x00 > vendor = 'Texas Instruments (TI)' > device = 'TSB82AA2 1394b OHCI-Lynx IEEE 1394 Host Controller' > class = serial bus > subclass = FireWire > > dmesg: > fwohci0: <Texas Instruments TSB82AA2> mem > 0xff904000-0xff9047ff,0xff900000-0xff903fff irq 22 at device 1.0 on pci2 > fwohci0: [FILTER] > fwohci0: OHCI version 1.10 (ROM=1) > fwohci0: No. of Isochronous channels is 4. > fwohci0: EUI64 00:13:3b:01:00:01:01:82 > fwohci0: invalid speed 7 (fixed to 3). > fwohci0: Phy 1394a available S800, 3 ports. > fwohci0: Link S800, max_rec 4096 bytes. > firewire0: <IEEE1394(FireWire) bus> on fwohci0 > > -- /\ Hidetoshi Shimokawa \/ simokawa@FreeBSD.ORG
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?626eb4530806112112w4b3873c6n195385af3db909cc>