Date: Mon, 17 Feb 2014 14:05:52 -0800 From: "Waitman Gobble" <uzimac@da3m0n8t3r.com> To: "Alex Deiter" <alex.deiter@gmail.com> Cc: Kevin Lo <kevlo@freebsd.org>, freebsd-wireless@freebsd.org Subject: Re: Ralink RT3573 / ASUS USB-N66: run0: could not load 8051 microcode Message-ID: <63a130f264cbfb29dc3fd34ab3170447.squirrel@mx.waitman.net> In-Reply-To: <CAAi9siYMdL12t6jHMyt9ZUaC541qneFrB5dWh2ooK2_%2Bnnw9_Q@mail.gmail.com> References: <CAAi9siYMdL12t6jHMyt9ZUaC541qneFrB5dWh2ooK2_%2Bnnw9_Q@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Mon, February 17, 2014 8:53 pm, Alex Deiter wrote: > Hello Kevin, > > > I'm trying to get ASUS USB-N66 USB wifi adapter working with FreeBSD > 11.0-CURRENT #0 r261642 amd64. > I plug the adapter and it seems to be recognized: > > > #dmesg > run0: <1.0> on usbus1 > run0: MAC/BBP RT3593 (rev 0x0402), RF RT3053 (MIMO 3T3R), address > 30:85:a9:f4:52:bd > run0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps > run0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps > run0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps > 24Mbps 36Mbps 48Mbps 54Mbps > > > I can create the wlan device: > > > # ifconfig wlan0 > wlan0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 > ether 30:85:a9:f4:52:bd nd6 > options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: IEEE 802.11 > Wireless Ethernet autoselect (autoselect) > status: no carrier > ssid "" channel 1 (2412 MHz 11b) country US authmode OPEN privacy OFF > txpower 0 bmiss 7 scanvalid 60 wme bintval 0 > > # ifconfig wlan0 list caps > drivercaps=d85c501<STA,IBSS,HOSTAP,SHSLOT,SHPREAMBLE,MONITOR,MBSS,WPA1,WPA > 2,WME,WDS> > cryptocaps=1b<WEP,TKIP,AES_CCM,TKIPMIC> > > But got an error when interface is up: > > > # ifconfig wlan0 up scan > wlan0: bpf attached > wlan0: bpf attached > wlan0: Ethernet address: 30:85:a9:f4:52:bd > firmware: 'runfw' version 1: 8192 bytes loaded at 0xffffffff81c2d0a8 > run0: could not load 8051 microcode > > > # usbconfig -d ugen1.3 dump_device_desc > ugen1.3: <802.11 n WLAN Ralink> at usbus1, cfg=0 md=HOST spd=HIGH > (480Mbps) > pwr=ON (450mA) > > bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0200 bDeviceClass = > 0x0000 > bDeviceSubClass = 0x0000 bDeviceProtocol = 0x0000 bMaxPacketSize0 = 0x0040 > idVendor = 0x0b05 idProduct = 0x17ad bcdDevice = 0x0101 iManufacturer = > 0x0001 <Ralink> > iProduct = 0x0002 <802.11 n WLAN> iSerialNumber = 0x0003 <1.0> > bNumConfigurations = 0x0001 > > # kldstat > Id Refs Address Size Name > 1 12 0xffffffff80200000 196df88 kernel > 2 1 0xffffffff81c12000 17db4 if_run.ko > 3 1 0xffffffff81c2a000 2a45 uhid.ko > 4 1 0xffffffff81c2d000 26ea runfw.ko > > > Kernel config: GENERIC. > > > I plug in the same adapter to a laptop with Windows 7, it successfully > shows the nearby access points and allows me to connect to one, so the > adapter is not broken. Any ideas for further troubleshooting are welcome. > > > Thank you! > > > -- > Alex Deiter > _______________________________________________ > freebsd-wireless@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-wireless > To unsubscribe, send any mail to > "freebsd-wireless-unsubscribe@freebsd.org" > > Alex, I've been using a device with the same chipset on HEAD without trouble. It's not ASUS but hmmm. (i don't see a brand name on it anywhere but 'made in china' is mighty prominent). # ifconfig wlan0 create wlandev run0 ssid "SSID" # wpa_supplicant -B -i wlan0 -c /etc/"SSID".conf # ifconfig wlan0 up # ifconfig wlan0 inet "IP" netmask 255.255.255.0 this driver is in src/sys/dev/usb/wlan/if_run.c, RUN_DEV(RALINK, RT3573), {should be supported} AFAIK there isn't a specific kernel option for the run device. > kldstat | grep run 12 1 0xffffffff81a14000 13309 if_run.ko you can take a look at #man runfw > find /boot/ | grep run /boot/kernel/if_run.ko /boot/kernel/runfw.ko /boot/kernel.old/if_run.ko /boot/kernel.old/runfw.ko I think the firmware should be in src/sys/contrib/dev/run -- Waitman Gobble San Jose California USA +1.510-830-7975
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?63a130f264cbfb29dc3fd34ab3170447.squirrel>