Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 11 Aug 2003 12:04:33 -0400
From:      Joe Marcus Clarke <marcus@marcuscom.com>
To:        current@freebsd.org
Subject:   Problem using USB 2.0 device under -CURRENT
Message-ID:  <1060617873.788.18.camel@gyros>

next in thread | raw e-mail | index | archive | help

--=-vvLTUEqYakv92KGAAZoV
Content-Type: text/plain; charset=ISO-8859-1
Content-Transfer-Encoding: quoted-printable

I'm running:

FreeBSD 5.1-CURRENT #18: Sat Aug  9 16:53:59 EDT 2003
    marcus@gyros.marcuscom.com:/usr/obj/usr/src/sys/GYROS

And I just bought one of those 256 MB USB JumpDrives.  The drive works
fine under -STABLE and in USB 1.1 slots on -CURRENT:

umass0: LEXAR   MEDIA JUMPDRIVE PRO, rev 2.00/0.00, addr 2
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <LEXAR JUMPDRIVE PRO 0> Removable Direct Access SCSI-2 device
da0: 1.000MB/s transfers
da0: 246MB (503808 512 byte sectors: 64H 32S/T 246C)

However, if I have ehci compiled into my kernel (needed to get usbd to
detect new devices), I see the following when I plug the drive in:

usb3: unrecoverable error, controller halted
usb3: blocking intrs 0x10

USB does work on this machine (as long as the device is a USB 1.x
device).  I have tested a USB mouse, a Sony camera, and a USB serial
adapter.  All work as expected.  I have an Intel-based USB controller in
this laptop:

ehci0@pci0:29:7:        class=3D0x0c0320 card=3D0x015f1028 chip=3D0x24cd808=
6
rev=3D0x03
hdr=3D0x00
    vendor   =3D 'Intel Corporation'
    device   =3D '82801DB (ICH4) USB EHCI Controller'
    class    =3D serial bus
    subclass =3D USB

But, of course, it's detected as a generic EHCI controller:

ehci0: <EHCI (generic) USB 2.0 controller> mem 0xd0000000-0xd00003ff irq
10 at device 29.7 on pci0
ehci_pci_attach: companion usb0
ehci_pci_attach: companion usb1
ehci_pci_attach: companion usb2
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <EHCI (generic) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: (0x8086) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered

I haven't tried applying the patch to get it detected as an actual Intel
controller, but I'm not sure that would help.  Any ideas?  Full dmesg
follows.  Thanks.

Joe

Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.1-CURRENT #18: Sat Aug  9 16:53:59 EDT 2003
    marcus@gyros.marcuscom.com:/usr/obj/usr/src/sys/GYROS
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0510000.
Preloaded elf module "/boot/kernel/snd_ich.ko" at 0xc05102c8.
Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc0510374.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0510420.
Timecounter "i8254"  frequency 1193182 Hz
CPU: Genuine Intel(R) CPU 3.06GHz (3056.50-MHz 686-class CPU)
  Origin =3D "GenuineIntel"  Id =3D 0xf29  Stepping =3D 9
=20
Features=3D0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,=
MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
real memory  =3D 1072562176 (1022 MB)
avail memory =3D 1036513280 (988 MB)
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL   MwoodNwd> on motherboard
pcibios: BIOS version 2.10
Using $PIR table, 9 entries at 0xc00fdf30
    ACPI-1287: *** Error: Method execution failed
[\\_SB_.PCI0.LPCB.BAT1._STA] (Node 0xc61375a0), AE_NOT_EXIST
acpi0: power button is handled as a fixed feature programming model.
Timecounter "ACPI-fast"  frequency 3579545 Hz
    ACPI-1287: *** Error: Method execution failed
[\\_SB_.PCI0.LPCB.BAT1._STA] (Node 0xc61375a0), AE_NOT_EXIST
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_cpu1: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib0: slot 29 INTA is routed to irq 10
pcib0: slot 29 INTB is routed to irq 11
pcib0: slot 29 INTC is routed to irq 11
pcib0: slot 29 INTD is routed to irq 10
pcib0: slot 31 INTB is routed to irq 10
pcib0: slot 31 INTB is routed to irq 10
pcib0: slot 31 INTB is routed to irq 10
agp0: <Intel Generic host to PCI bridge> mem 0xe0000000-0xefffffff at
device 0.0 on pci0
pci0: <base peripheral> at device 0.1 (no driver attached)
pci0: <base peripheral> at device 0.3 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib1: slot 0 INTA is routed to irq 5
pci1: <display, VGA> at device 0.0 (no driver attached)
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0x1800-0x181f
irq 10 at device 29.0 on pci0
usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: Microsoft Microsoft IntelliMouse=AE Explorer, rev 1.10/1.14, addr 2,
iclass 3/1
ums0: 5 buttons and Z dir.
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0x1820-0x183f
irq 11 at device 29.1 on pci0
usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0x1840-0x185f
irq 11 at device 29.2 on pci0
usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xd0000000-0xd00003ff irq
10 at device 29.7 on pci0
ehci_pci_attach: companion usb0
ehci_pci_attach: companion usb1
ehci_pci_attach: companion usb2
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <EHCI (generic) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: (0x8086) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib2: slot 1 INTA is routed to irq 10
pcib2: slot 4 INTA is routed to irq 10
pcib2: slot 4 INTA is routed to irq 10
pci2: <network, ethernet> at device 1.0 (no driver attached)
cbb0: <TI4510 PCI-CardBus Bridge> irq 10 at device 4.0 on pci2
start (88000000) < sc->membase (d0200000)
end (ffffffff) > sc->memlimit (d02fffff)
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fwohci0: vendor=3D104c, dev=3D8029
fwohci0: <1394 Open Host Controller Interface> mem
0xd0200000-0xd0203fff,0xd0206000-0xd02067ff irq 10 at device 4.1 on pci2
fwohci0: OHCI version 1.10 (ROM=3D0)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 00:c0:4f:34:0d:90:90:61
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
sbp0: <SBP2/SCSI over firewire> on firewire0
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=3D0xc000ffc0, gen=3D1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <=3D 0, cable IRM =3D 0 (me)
firewire0: bus manager 0 (me)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port
0x1860-0x186f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pcm0: <Intel ICH4 (82801DB)> port 0x18c0-0x18ff,0x1c00-0x1cff mem
0xd0000800-0xd00008ff,0xd0000c00-0xd0000dff irq 10 at device 31.5 on
pci0
pcm0: <SigmaTel STAC9750/51 AC97 Codec>
pci0: <simple comms> at device 31.6 (no driver attached)
acpi_ec0: <embedded controller: GPE 0x1c> port 0x66,0x62 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
acpi_acad0: <AC adapter> on acpi0
orm0: <Option ROMs> at iomem
0xe0000-0xe3fff,0xdc000-0xdffff,0xd1000-0xd27ff,0xd0000-0xd0fff,0xc0000-0xc=
ffff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
Timecounter "TSC"  frequency 3056502372 Hz
Timecounters tick every 10.000 msec
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
system power profile changed to 'economy'
ad2: 57231MB <HITACHI_DK23FB-60> [116280/16/63] at ata1-master UDMA100
acd0: CD-RW <QSI CD-RW/DVD-ROM SBW-242> at ata0-master UDMA33
ums0: at uhub0 port 1 (addr 2) disconnected
ums0: detached
ums0: Microsoft Microsoft IntelliMouse=AE Explorer, rev 1.10/1.14, addr 2,
iclass 3/1
ums0: 5 buttons and Z dir.
Mounting root from ufs:/dev/ad2s3a
cd0 at ata0 bus 0 target 0 lun 0
cd0: <QSI CDRW/DVD SBW-242 UD22> Removable CD-ROM SCSI-0 device=20
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
system power profile changed to 'performance'
bcm0: <Broadcom 10/100 Base-T Ethernet> mem 0xd0204000-0xd0205fff irq 10
at device 1.0 on pci2
bcm0: Ethernet address: 00:0b:db:9c:4a:bd
miibus0: <MII bus> on bcm0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
drm0: <ATI Radeon Lf R250 Mobility 9000 M9> port 0x3000-0x30ff mem
0xd0100000-0xd010ffff,0xd8000000-0xdfffffff irq 5 at device 0.0 on pci1
info: [drm] AGP at 0xe0000000 256MB
info: [drm] Initialized radeon 1.8.0 20020828 on minor 0
info: [drm] Loading R200 Microcode
stray irq 7
stray irq 7
ums0: at uhub0 port 1 (addr 2) disconnected
ums0: detached
usb3: unrecoverable error, controller halted
usb3: blocking intrs 0x10
uhub3: device problem, disabling port 1
ums0: Microsoft Microsoft IntelliMouse=AE Explorer, rev 1.10/1.14, addr 2,
iclass 3/1
ums0: 5 buttons and Z dir.


--=20
PGP Key : http://www.marcuscom.com/pgp.asc



--=-vvLTUEqYakv92KGAAZoV
Content-Type: application/pgp-signature; name=signature.asc
Content-Description: This is a digitally signed message part

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.2 (FreeBSD)

iD8DBQA/N76Rb2iPiv4Uz4cRAmvBAKCAQ9MVHEHC+IY3Wjhlww87J5vNFwCgi2WK
dM+Z8SV2TeFGwMkWCczygFI=
=Uh35
-----END PGP SIGNATURE-----

--=-vvLTUEqYakv92KGAAZoV--



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1060617873.788.18.camel>