Date: Sun, 18 Aug 2002 16:28:52 +0400 From: Kirill Bezzubets <kirill@solaris.ru> To: Emanuel Haupt <emanuel.haupt@cablecom.ch> Cc: freebsd-mobile@FreeBSD.org Subject: Re: pcmcia modem Message-ID: <20020818162851.A77100@solaris.ru> In-Reply-To: <20020818123339.0a6d2906.emanuel.haupt@cablecom.ch>; from emanuel.haupt@cablecom.ch on Sun, Aug 18, 2002 at 12:33:39PM %2B0200 References: <20020816132451.21c47f46.emanuel.haupt@cablecom.ch> <20020818110807.A13620@solaris.ru> <20020818120556.20db0764.emanuel.haupt@cablecom.ch> <20020818141450.A8702@solaris.ru> <20020818123339.0a6d2906.emanuel.haupt@cablecom.ch>
next in thread | previous in thread | raw e-mail | index | archive | help
On Sun, Aug 18, 2002 at 12:33:39PM +0200, Emanuel Haupt wrote: > > > > 3rd: Can you communicate with your modem using cu/ecu? > > > > > > cu -l /dev/cuaa4 -s 9600 > > > freezes freebsd completely! > > > > > > its freebsd 5.0-DP1. i am using the NEWCARD kernel because > sometimes i need other cards: ethernetcard, wireless card. but > while that "irq trouble" happens there is no other pcmcia card > inserted. Actually, I never tried NEWCARD kernel yet. The only 5.0-DP1 I have is my desktop, my notebook is 4.6-STABLE. So it's better to address your question to M. Warner Losh, I see lines that might describe problem, but I don't know the meaning: > pccard1: Allocation failed for cfe 32 > pccard1: Allocation failed for cfe 33 > > it might help you to see my whole dmesg output: > > Copyright (c) 1992-2002 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, > 1993, 1994 > The Regents of the University of California. All rights > reserved. > FreeBSD 5.0-DP1 #0: Fri Jul 26 10:40:11 CEST 2002 > root@:/usr/src/sys/i386/compile/DEEDEE > Preloaded elf kernel "/boot/kernel/kernel" at 0xc0570000. > Preloaded elf module "/boot/kernel/acpi.ko" at 0xc05700a8. > Timecounter "i8254" frequency 1193182 Hz > Timecounter "TSC" frequency 498470138 Hz > CPU: Pentium III/Pentium III Xeon/Celeron (498.47-MHz > 686-class CPU) > Origin = "GenuineIntel" Id = 0x686 Stepping = 6 > > Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTR > R,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> > real memory = 134066176 (130924K bytes) > avail memory = 124407808 (121492K bytes) > Pentium Pro MTRR support enabled > Using $PIR table, 6 entries at 0xc00fbd20 > npx0: <math processor> on motherboard > npx0: INT 16 interface > acpi0: <DELL CPi R > on motherboard > ACPI timer looks BAD min = 2, max = 6, width = 5 > ACPI timer looks BAD min = 2, max = 6, width = 5 > ACPI timer looks BAD min = 2, max = 6, width = 5 > ACPI timer looks BAD min = 2, max = 6, width = 5 > ACPI timer looks BAD min = 2, max = 6, width = 5 > ACPI timer looks BAD min = 2, max = 6, width = 5 > ACPI timer looks BAD min = 2, max = 6, width = 5 > ACPI timer looks BAD min = 2, max = 6, width = 5 > ACPI timer looks BAD min = 2, max = 6, width = 5 > ACPI timer looks BAD min = 2, max = 6, width = 5 > Timecounter "ACPI-safe" frequency 3579545 Hz > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on > acpi0 > acpi_cpu0: <CPU> on acpi0 > acpi_tz0: <thermal zone> on acpi0 > acpi_acad0: <AC adapter> on acpi0 > acpi_cmbat0: <Control method Battery> on acpi0 > acpi_cmbat1: <Control method Battery> on acpi0 > acpi_lid0: <Control Method Lid Switch> on acpi0 > acpi_button0: <Power Button> on acpi0 > acpi_button1: <Sleep Button> on acpi0 > acpi_pcib0: <Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <PCI bus> on acpi_pcib0 > pcib1: <PCI-PCI bridge> at device 1.0 on pci0 > pci1: <PCI bus> on pcib1 > pci1: <display, VGA> at device 0.0 (no driver attached) > pccbb0: <TI1225 PCI-CardBus Bridge> at device 3.0 on pci0 > cardbus0: <CardBus bus> on pccbb0 > pccard0: <16-bit PCCard bus> on pccbb0 > acpi_pcib0: device is routed to IRQ 11 > pccbb1: <TI1225 PCI-CardBus Bridge> at device 3.1 on pci0 > cardbus1: <CardBus bus> on pccbb1 > pccard1: <16-bit PCCard bus> on pccbb1 > acpi_pcib0: device is routed to IRQ 11 > isab0: <PCI-ISA bridge> at device 7.0 on pci0 > isa0: <ISA bus> on isab0 > atapci0: <Intel PIIX4 ATA33 controller> port 0x860-0x86f at > device 7.1 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port > 0xdce0-0xdcff irq 11 at device 7.2 on pci0 > usb0: cannot stop > usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 > usb0: USB revision 1.0 > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached) > pci0: <multimedia, audio> at device 8.0 (no driver attached) > atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on > acpi0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: model GlidePoint, device ID 0 > fdc0: <enhanced floppy controller (i82077, NE72065 or clone)> > port 0x3f7,0x3f2-0x3f5 irq 6 on acpi0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > sio0 port 0x3f8-0x3ff irq 4 on acpi0 > sio0: type 16550A > sio1 port 0x280-0x287,0x2f8-0x2ff irq 3 on acpi0 > sio1: type 16550A > ppc0 port 0x778-0x77b,0x378-0x37f irq 7 on acpi0 > ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode > ppc0: FIFO with 16/16/8 bytes threshold > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0 > pmtimer0 on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem > 0xa0000-0xbffff on isa0 > system power profile changed to 'economy' > wi0: <WaveLAN/IEEE> at port 0x100-0x13f irq 11 function 0 > config 1 on pccard0 > wi0: 802.11 address: 00:90:d1:07:b0:64 > wi0: using RF:PRISM2 MAC:HFA3841 CARD:HWB3163 rev.A, Firmware: > 1.4 variant 9 > pccard1: Allocation failed for cfe 32 > pccard1: Allocation failed for cfe 33 > ed1: Total wildcard entry ignored for SVEC PN650TX 10/100 Dual > Speed Fast Ethernet PC Card > sio4 at port 0x3e8-0x3ef irq 11 function 0 config 34 on > pccard1 > sio4: type 16550A > sio4: unable to activate interrupt in fast mode - using normal > mode > ad0: 19077MB <IBM-DJSA-220> [38760/16/63] at ata0-master > UDMA33 > acd0: CDROM <SAMSUNG CD-ROM SN-124> at ata1-master PIO4 > Mounting root from ufs:/dev/ad0s1a -- BR, Kirill Bezzubets CASE-RIPE CASE-RIPN Senior Administrator, Technical Department mailto:kirill@solaris.ru Solaris ISP & Telecommunications Co. Ltd http://www.solaris.ru To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020818162851.A77100>